Abstract: In this paper, a design methodology to implement low-power and high-speed 2nd order recursive digital Infinite Impulse Response (IIR) filter has been proposed. Since IIR filters suffer from a large number of constant multiplications, the proposed method replaces the constant multiplications by using addition/subtraction and shift operations. The proposed new 6T adder cell is used as the Carry-Save Adder (CSA) to implement addition/subtraction operations in the design of recursive section IIR filter to reduce the propagation delay. Furthermore, high-level algorithms designed for the optimization of the number of CSA blocks are used to reduce the complexity of the IIR filter. The DSCH3 tool is used to generate the schematic of the proposed 6T CSA based shift-adds architecture design and it is analyzed by using Microwind CAD tool to synthesize low-complexity and high-speed IIR filters. The proposed design outperforms in terms of power, propagation delay, area and throughput when compared with MUX-12T, MCIT-7T based CSA adder filter design. It is observed from the experimental results that the proposed 6T based design method can find better IIR filter designs in terms of power and delay than those obtained by using efficient general multipliers.
Abstract: The objective of this study was to investigate hydrogen production from alcohol wastewater by anaerobic sequencing batch reactor (ASBR) under thermophillic operation. The ASBR unit used in this study had a liquid holding volume of 4 L and was operated at 6 cycles per day. The seed sludge taken from an upflow anaerobic sludge blanket unit treating the same wastewater was boiled at 95 °C for 15 min before being fed to the ASBR unit. The ASBR system was operated at different COD loading rates at a thermophillic temperature (55 °C), and controlled pH of 5.5. When the system was operated under optimum conditions (providing maximum hydrogen production performance) at a feed COD of 60 000 mg/l, and a COD loading rate of 68 kg/m3 d, the produced gas contained 43 % H2 content in the produced gas. Moreover, the hydrogen yield and the specific hydrogen production rate (SHPR) were 130 ml H2/g COD removed and 2100 ml H2/l d, respectively.
Abstract: In this paper, a new approach is introduced to solve
Blasius equation using parameter identification of a nonlinear
function which is used as approximation function. Bees Algorithm
(BA) is applied in order to find the adjustable parameters of
approximation function regarding minimizing a fitness function
including these parameters (i.e. adjustable parameters). These
parameters are determined how the approximation function has to
satisfy the boundary conditions. In order to demonstrate the
presented method, the obtained results are compared with another
numerical method. Present method can be easily extended to solve a
wide range of problems.
Abstract: Rule Discovery is an important technique for mining
knowledge from large databases. Use of objective measures for
discovering interesting rules leads to another data mining problem,
although of reduced complexity. Data mining researchers have
studied subjective measures of interestingness to reduce the volume
of discovered rules to ultimately improve the overall efficiency of
KDD process.
In this paper we study novelty of the discovered rules as a
subjective measure of interestingness. We propose a hybrid approach
based on both objective and subjective measures to quantify novelty
of the discovered rules in terms of their deviations from the known
rules (knowledge). We analyze the types of deviation that can arise
between two rules and categorize the discovered rules according to
the user specified threshold. We implement the proposed framework
and experiment with some public datasets. The experimental results
are promising.
Abstract: Fundamental motivation of this paper is how gaze estimation can be utilized effectively regarding an application to games. In games, precise estimation is not always important in aiming targets but an ability to move a cursor to an aiming target accurately is also significant. Incidentally, from a game producing point of view, a separate expression of a head movement and gaze movement sometimes becomes advantageous to expressing sense of presence. A case that panning a background image associated with a head movement and moving a cursor according to gaze movement can be a representative example. On the other hand, widely used technique of POG estimation is based on a relative position between a center of corneal reflection of infrared light sources and a center of pupil. However, a calculation of a center of pupil requires relatively complicated image processing, and therefore, a calculation delay is a concern, since to minimize a delay of inputting data is one of the most significant requirements in games. In this paper, a method to estimate a head movement by only using corneal reflections of two infrared light sources in different locations is proposed. Furthermore, a method to control a cursor using gaze movement as well as a head movement is proposed. By using game-like-applications, proposed methods are evaluated and, as a result, a similar performance to conventional methods is confirmed and an aiming control with lower computation power and stressless intuitive operation is obtained.
Abstract: Protein structure determination and prediction has
been a focal research subject in the field of bioinformatics due to the
importance of protein structure in understanding the biological and
chemical activities of organisms. The experimental methods used by
biotechnologists to determine the structures of proteins demand
sophisticated equipment and time. A host of computational methods
are developed to predict the location of secondary structure elements
in proteins for complementing or creating insights into experimental
results. However, prediction accuracies of these methods rarely
exceed 70%.
Abstract: the intension in this work is to investigate the effect of
different bending manifold pipes on engine performance for different
engine speed. Power, Torque, and BSFC were calculated and
presented to show the effect of varying bending pipes angles on them
for all cases considered. A special program used to carry out the
calculations. A simulation model for 4-cylinders spark ignition
engine with turbocharger has been built and calculated. The analysis
of the results shows that for 120o angle the torque increases about
40% at 3000 rpm and 25% at 4000 rpm without changing in fuel
consumption. For 90o angle the increment in torque is about 10 %.
For the same bending angle the increment in brake power is around
40% at 3000 rpm and 25% at 4000 rpm. The increment in fuel
consumption is about 12% for 60o and 30% for 90o between (6000-
7000) rpm.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: This paper proposes an efficient learning method for the layered neural networks based on the selection of training data and input characteristics of an output layer unit. Comparing to recent neural networks; pulse neural networks, quantum neuro computation, etc, the multilayer network is widely used due to its simple structure. When learning objects are complicated, the problems, such as unsuccessful learning or a significant time required in learning, remain unsolved. Focusing on the input data during the learning stage, we undertook an experiment to identify the data that makes large errors and interferes with the learning process. Our method devides the learning process into several stages. In general, input characteristics to an output layer unit show oscillation during learning process for complicated problems. The multi-stage learning method proposes by the authors for the function approximation problems of classifying learning data in a phased manner, focusing on their learnabilities prior to learning in the multi layered neural network, and demonstrates validity of the multi-stage learning method. Specifically, this paper verifies by computer experiments that both of learning accuracy and learning time are improved of the BP method as a learning rule of the multi-stage learning method. In learning, oscillatory phenomena of a learning curve serve an important role in learning performance. The authors also discuss the occurrence mechanisms of oscillatory phenomena in learning. Furthermore, the authors discuss the reasons that errors of some data remain large value even after learning, observing behaviors during learning.
Abstract: Web sites are rapidly becoming the preferred media
choice for our daily works such as information search, company
presentation, shopping, and so on. At the same time, we live in a
period where visual appearances play an increasingly important
role in our daily life. In spite of designers- effort to develop a web
site which be both user-friendly and attractive, it would be difficult
to ensure the outcome-s aesthetic quality, since the visual
appearance is a matter of an individual self perception and opinion.
In this study, it is attempted to develop an automatic system for
web pages aesthetic evaluation which are the building blocks of
web sites. Based on the image processing techniques and artificial
neural networks, the proposed method would be able to categorize
the input web page according to its visual appearance and aesthetic
quality. The employed features are multiscale/multidirectional
textural and perceptual color properties of the web pages, fed to
perceptron ANN which has been trained as the evaluator. The
method is tested using university web sites and the results
suggested that it would perform well in the web page aesthetic
evaluation tasks with around 90% correct categorization.
Abstract: Validity is an overriding consideration in language testing. If a test score is intended for a particular purpose, this must be supported through empirical evidence. This article addresses the validity of a multiple-choice achievement test (MCT). The test is administered at the end of each semester to decide about students' mastery of a course in general English. To provide empirical evidence pertaining to the validity of this test, two criterion measures were used. In so doing, a Cloze test and a C-test which are reported to gauge general English proficiency were utilized. The results of analyses show that there is a statistically significant correlation among participants' scores on the MCT, Cloze, and Ctest. Drawing on the findings of the study, it can be cautiously deduced that these tests measure the same underlying trait. However, allowing for the limitations of using criterion measures to validate tests, we cannot make any absolute claim as to the validity of this MCT test.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: Einstein vacuum equations, that is a system of nonlinear
partial differential equations (PDEs) are derived from Weyl metric
by using relation between Einstein tensor and metric tensor. The
symmetries of Einstein vacuum equations for static axisymmetric
gravitational fields are obtained using the Lie classical method. We
have examined the optimal system of vector fields which is further
used to reduce nonlinear PDE to nonlinear ordinary differential
equation (ODE). Some exact solutions of Einstein vacuum equations
in general relativity are also obtained.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: To offer a large variety of products while maintaining
low costs, high speed, and high quality in a mass customization
product development environment, platform based product
development has much benefit and usefulness in many industry fields.
This paper proposes a product configuration strategy by similarity
measure, incorporating the knowledge engineering principles such as
product information model, ontology engineering, and formal concept
analysis.
Abstract: Today many developers use the Java components
collected from the Internet as external LIBs to design and
develop their own software. However, some unknown security
bugs may exist in these components, such as SQL injection bug
may comes from the components which have no specific check
for the input string by users. To check these bugs out is very
difficult without source code. So a novel method to check the
bugs in Java bytecode based on points-to dataflow analysis is in
need, which is different to the common analysis techniques base
on the vulnerability pattern check. It can be used as an assistant
tool for security analysis of Java bytecode from unknown
softwares which will be used as extern LIBs.
Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.