Abstract: In this research the effects of adding silica and
alumina nanoparticles on flow ability and compressive strength of
cementitious composites based on Portland cement were investigated.
In the first stage, the rheological behavior of different samples
containing nanosilica, nanoalumina and polypropylene, polyvinyl
alcohol and polyethylene fibers were evaluated. With increasing of
nanoparticles in fresh samples, the slump flow diameter reduced.
Fibers reduced the flow ability of the samples and viscosity
increased. With increasing of the micro silica particles to cement
ratio from 2/1 to 2/2, the slump flow diameter increased. By adding
silica and alumina nanoparticles up to 3% and 2% respectively, the
compressive strength increased and after decreased. Samples
containing silica nanoparticles and fibers had the highest compressive
strength.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: A collection of thirty cultivars/clones of a red pitaya
was used to investigate flowering response to lighting
supplementation in the winter season of 2013-2014 in southern
Taiwan. The night-breaking treatment was conducted during the
period of 10 Oct. 2013 to 5 Mar. 2014 with 4-continuous hours
(22.00 – 02.00 hrs) of additional lighting daily using incandescent
bulbs (100W). Among cultivars and clones tested, twenty-three
genotypes, most belonging to the red-magenta flesh type, were found
to have positively flowering response to the lighting treatment. The
duration of night-breaking treatment for successful flowering
initiation varied from 33- 48 days. The lighting-sensitive genotypes
bore 1-2 flowering flushes. Floral and fruiting stages took 21-26 and
46-59 days, respectively. Among sixteen fruiting genotypes, the
highest fruit set rates were found in Damao 9, D4, D13, Chaozou
large, Chaozhou 5, Small Nick and F22. Five cultivars and clones
(Orejona, D4, Chaozhou large, Chaozhou 5 and Small Nick) produced
fruits with an average weight of more than 300 g per fruit which were
higher than those of the fruits formed in the summer of 2013. Fruits
produced during off-season containing total soluble solids (TSS)
from 17.5 to 20.7oBrix, which were higher than those produced inseason.
Abstract: The purpose of this study is to forecast the influences
of information and communication technology (ICT) on the structural
changes of Japanese economies. In this study, input-output (IO) and
statistical approaches are used as analysis instruments. More
specifically, this study employs Leontief IO coefficients and
constrained multivariate regression (CMR) model in order to achieve
the purpose. The periods of initial and forecast in this study are 2005
and 2015, respectively. In this study, ICT is represented by ICT capital
stocks. This study conducts two levels of analysis, namely macro and
micro. The results of macro level analysis show that the dynamics of
Japanese economies on the forecast period, relative to the initial period,
are not so high. We focus on (1) commerce, (2) business services and
office supplies, and (3) personal services sectors when conducting the
analysis of the micro level. Further, we analyze its specific IO
coefficients when doing this analysis. The results of the analysis
explain that ICT gives a strong influence on the changes of these
coefficients from initial to forecast periods.
Abstract: Verification and Validation of Simulated Process
Model is the most important phase of the simulator life cycle.
Evaluation of simulated process models based on Verification and
Validation techniques checks the closeness of each component model
(in a simulated network) with the real system/process with respect to
dynamic behaviour under steady state and transient conditions. The
process of Verification and Validation helps in qualifying the process
simulator for the intended purpose whether it is for providing
comprehensive training or design verification. In general, model
verification is carried out by comparison of simulated component
characteristics with the original requirement to ensure that each step
in the model development process completely incorporates all the
design requirements. Validation testing is performed by comparing
the simulated process parameters to the actual plant process
parameters either in standalone mode or integrated mode.
A Full Scope Replica Operator Training Simulator for PFBR -
Prototype Fast Breeder Reactor has been developed at IGCAR,
Kalpakkam, INDIA named KALBR-SIM (Kalpakkam Breeder
Reactor Simulator) where in the main participants are
engineers/experts belonging to Modeling Team, Process Design and
Instrumentation & Control design team. This paper discusses about
the Verification and Validation process in general, the evaluation
procedure adopted for PFBR operator training Simulator, the
methodology followed for verifying the models, the reference
documents and standards used etc. It details out the importance of
internal validation by design experts, subsequent validation by
external agency consisting of experts from various fields, model
improvement by tuning based on expert’s comments, final
qualification of the simulator for the intended purpose and the
difficulties faced while co-coordinating various activities.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: This study attempts to elicit the perceptions and
attitudes of EFL learners of the Preparatory Year Program at KSU
towards dialogue journal writing as an EFL learning strategy. The
descriptive research design used incorporated both qualitative and
quantitative instruments to accomplish the objectives of the study. A
learners’ attitude questionnaire and follow-up interviewswith learners
from a randomly selected representative sample of the participants
were employed. The participants were 55 female Saudi university
students in the Preparatory Year Program at King Saud University.
The analysis of the results indicated that the PYP learners had highly
positive attitudes towards dialogue journal writing in their EFL
classes and positive perceptions of the benefits of the use of dialogue
journal writing as an EFL learning strategy. The results also revealed
that dialogue journals are considered an effective EFL learning
strategy since they fulfill various needs for both learners and
instructors. Interestingly, the analysis of the results also revealed that
Saudi university level students tend to write about personal topics in
their dialogue journals more than academic ones.
Abstract: The design and plantwide control of an integrated
plant where the endothermic 1,4-butanediol dehydrogenation and the
exothermic furfural hydrogenation is simultaneously performed in a
single reactor is studied. The reactions can be carried out in an
adiabatic reactor using small hydrogen excess and with reduced
parameter sensitivity. The plant is robust and flexible enough to
allow different production rates of γ-butyrolactone and 2-methyl
furan, keeping high product purities. Rigorous steady state and
dynamic simulations performed in AspenPlus and AspenDynamics to
support the conclusions.
Abstract: Malaysia is rich with historic buildings, particularly in
Penang and Malacca states. Restoration activities are increasingly
important as these states are recognized under UNESCO World
Heritage Sites. Restoration activities help to maintain the uniqueness
and value of a heritage building. However, increasing in restoration
activities has resulted in large quantities of waste. To cope with this
problem, the 3R concept (reduce, reuse and recycle) is introduced.
The 3R concept is one of the waste management hierarchies. This
concept is still yet to apply in the building restoration industry
compared to the construction industry. Therefore, this study aims to
promote the 3R concept in the heritage building restoration industry.
This study aims to examine the importance of 3R concept and to
identify challenges in applying the 3R concept in the heritage
building restoration industry. This study focused on contractors and
consultants who are involved in heritage restoration projects in
Penang. Literature review and interviews helps to reach the research
objective. Data that obtained is analyzed by using content analysis.
For the research, application of 3R concept is important to conserve
natural resources and reduce pollution problems. However, limited
space to organise waste is the obstruction during the implementation
of this concept. In conclusion, the 3R concept plays an important role
in promoting environmental conservation and helping in reducing the
construction waste.
Abstract: The emerging Cognitive Radio is combo of both the
technologies i.e. Radio dynamics and software technology. It involve
wireless system with efficient coding, designing, and making them
artificial intelligent to take the decision according to the surrounding
environment and adopt themselves accordingly, so as to deliver the
best QoS. This is the breakthrough from fixed hardware and fixed
utilization of the spectrum. This software-defined approach of
research is centralized at user-definition and application driven
model, various software method are used for the optimization of the
wireless communication. This paper focused on the Spectrum
allocation technique using genetic algorithm GA to evolve radio,
represented by chromosomes. The chromosomes gene represents the
adjustable parameters in given radio and by using GA, evolving over
the generations, the optimized set of parameters are evolved, as per
the requirement of user and availability of the spectrum, in our
prototype the gene consist of 6 different parameters, and the best set
of parameters are evolved according to the application need and
availability of the spectrum holes and thus maintaining best QoS for
user, simultaneously maintaining licensed user rights. The analyzing
tool Matlab is used for the performance of the prototype.
Abstract: Bio-composites derived from plant fiber and/or bioderived
polymer, are likely more ecofriendly and demonstrate
competitive performance with petroleum based composites. In this
research, the bio phenol-formaldehyde (bio-PF) was used as a matrix
and oil palm empty fruit bunch fiber (EFB) as reinforcement. The
matrix was synthesized via liquefaction and condensation to enhance
the combination of phenol and formaldehyde, during the process.
Then, the bio-PF was mixed with different percentage of EFB (5%,
10%, 15% and 20%) and molded at 180oC. The samples that viewed
under scanning electron microscopy (SEM) showed an excellent
wettability and interaction between EFB and matrix. Samples of 10%
EFB gave the optimum properties of impact and hardness meanwhile
sample 15% of EFB gave the highest reading of flexural modulus
(MOE) and flexural strength (MOR). For thermal stability analysis, it
was found that the weight loss and the activation energy (Ea) of the
bio-composites samples were decreased as the filler content
increased.
Abstract: Managing and improving efficiency in the current
highly competitive global automotive industry demands that those
companies adopt leaner and more flexible systems. During the past
20 years the domestic automotive industry in North America has been
focusing on establishing new management strategies in order to meet
market demands. The lean management process also known as
Toyota Manufacturing Process (TPS) or lean manufacturing
encompasses tools and techniques that were established in order to
provide the best quality product with the fastest lead time at the
lowest cost. The following paper presents a study that focused on
improving labor efficiency at one of the Big Three (Ford, GM,
Chrysler LLC) domestic automotive facility in North America. The
objective of the study was to utilize several lean management tools in
order to optimize the efficiency and utilization levels at the “Pre-
Marriage” chassis area in a truck manufacturing and assembly
facility. Utilizing three different lean tools (i.e. Standardization of
work, 7 Wastes, and 5S) this research was able to improve efficiency
by 51%, utilization by 246%, and reduce operations by 14%. The
return on investment calculated based on the improvements made
was 284%.
Abstract: Eucalyptus species are well reputed for their
traditional use in Asia as well as in other parts of the world; therefore,
the present study was designed to investigate the antimicrobial and
antioxidant activities associated with essential oils from different
Eucalyptus species. Essential oils from the leaves of six Eucalyptus
species, including: Eucalyptus woodwardi, Eucalyptus stricklandii,
Eucalyptus salubris, Eucalyptus sargentii, Eucalyptus torquata and
Eucalyptus wandoo were separated by hydrodistillation and dried
over anhydrous sodium sulphate. DPPH, ferric reducing antioxidant
power, and hydroxyl radical scavenging activity assays were carried
out to evaluate the antioxidant potential of the oils. The results
indicate that examined oils exhibit substantial antioxidant activities
relative to ascorbic acid. Previously, these oils were evaluated for
their antimicrobial activities, against wide range of bacterial and
fungal strains, and they were shown to possess significant
antimicrobial activities. In this study, further investigation into the
growth kinetics of oil-treated microbial cultures was conducted. The
results clearly demonstrate that the microbial growth was markedly
inhibited when treated with sub-MIC concentrations of the oils.
Taken together, the results obtained indicate a high potential of the
examined essential oils as bioactive oils, for nutraceutical and
medical applications, possessing significant antioxidant and anti
microbial activities.
Abstract: This paper presents modeling of an Alternating
Current (AC) Photovoltaic (PV) module using Matlab/Simulink. The
proposed AC-PV module model is simple, realistic, and application
oriented. The model is derived on module level as compared to cell
level directly from the information provided by the manufacturer data
sheet. DC-PV module, MPPT control, BC, VSI and LC filter, all
were treated as a single unit. The model accounts for changes in
variations of both irradiance and temperature. The AC-PV module
proposed model is simulated and the results are compared with the
datasheet projected numbers to validate model’s accuracy and
effectiveness. Implementation and results demonstrate simplicity and
accuracy, as well as reliability of the model.
Abstract: In this paper, a nonlinear Finite Element Analysis
(FEA) was carried out using ANSYS software to build a model able
of predicting the behavior of Reinforced Concrete (RC) beams with
unbonded reinforcement. The FEA model was compared to existing
experimental data by other researchers. The existing experimental
data consisted of 16 beams that varied from structurally sound beams
to beams with unbonded reinforcement with different unbonded
lengths and reinforcement ratios. The model was able to predict the
ultimate flexural strength, load-deflection curve, and crack pattern of
concrete beams with unbonded reinforcement. It was concluded that
when the when the unbonded length is less than 45% of the span,
there will be no decrease in the ultimate flexural strength due to the
loss of bond between the steel reinforcement and the surrounding
concrete regardless of the reinforcement ratio. Moreover, when the
reinforcement ratio is relatively low, there will be no decrease in
ultimate flexural strength regardless of the length of unbond.
Abstract: Fast changing knowledge systems on the Internet can
be accessed more efficiently with the help of automatic document
summarization and updating techniques. The aim of multi-document
update summary generation is to construct a summary unfolding the
mainstream of data from a collection of documents based on the
hypothesis that the user has already read a set of previous documents.
In order to provide a lot of semantic information from the documents,
deeper linguistic or semantic analysis of the source documents were
used instead of relying only on document word frequencies to select
important concepts. In order to produce a responsive summary,
meaning oriented structural analysis is needed. To address this issue,
the proposed system presents a document summarization approach
based on sentence annotation with aspects, prepositions and named
entities. Semantic element extraction strategy is used to select
important concepts from documents which are used to generate
enhanced semantic summary.
Abstract: A Motzkin shift is a mathematical model for constraints
on genetic sequences. In terms of the theory of symbolic dynamics,
the Motzkin shift is nonsofic, and therefore, we cannot use the Perron-
Frobenius theory to calculate its topological entropy. The Motzkin
shift M(M,N) which comes from language theory, is defined to be the
shift system over an alphabet A that consists of N negative symbols,
N positive symbols and M neutral symbols. For an x in the full shift,
x will be in the Motzkin subshift M(M,N) if and only if every finite
block appearing in x has a non-zero reduced form. Therefore, the
constraint for x cannot be bounded in length. K. Inoue has shown that
the entropy of the Motzkin shift M(M,N) is log(M + N + 1). In this
paper, a new direct method of calculating the topological entropy of
the Motzkin shift is given without any measure theoretical discussion.
Abstract: This research study aimed to survey and analyze the
attitudes of pre-service teachers’ the analytical thinking development
based on Miller’s Model. The informants of this study were 22 third
year teacher students majoring in Thai. The course where the
instruction was conducted was English for Academic Purposes in
Thai Language 2. The instrument of this research was an open-ended
questionnaire with two dimensions of questions: academic and
satisfaction dimensions. The investigation revealed the positive
attitudes. In the academic dimension, the majority of 12 (54.54%),
the highest percentage, reflected that the method of teaching
analytical thinking and language simultaneously was their new
knowledge and the similar percentage also belonged to text cohesion
in writing. For the satisfaction, the highest frequency count was from
17 of them (77.27%) and this majority favored the openness or
friendliness of the teacher.
Abstract: VACTERL association is a rare disorder with various
congenital malformations. The aetiology remains unknown.
Combination of at least three congenital anomalies of the following
criteria is required for diagnosis: vertebral defects, anal atresia,
cardiac anomalies, tracheo-esophageal fistula, renal anomalies, and
limb defects. The first case was 1-day old male neonate with multiple
congenital anomalies was bore from 28 years old mother. The mother
had history of pregnancy with lymphocyte therapy. His anomalies
included: defects in thoracic and lumbar vertebral, anal atresia,
bilateral hydronephrosis, atrial septal defect, and lower limb
abnormality. Other anomalies were cryptorchidism and nasal canal
narrowing. The second case was born with 32 weeks gestational age
from mother with history of pregnancy with lymphocyte therapy. He
had thoracic vertebral defect, cardiac anomalies and renal defect.
diagnosis based on clinical finding is VACTERL association. Early
diagnosis is very important to investigation and treatment of other
coexistence anomalies. VACTERL association in mothers with
history of pregnancy with lymphocyte therapy has suggested possibly
of relationship between VACTERL association and this method of
pregnancy.
Abstract: In the present work, the alloy of Bismuth-lead is
prepared on the basis of percentage of molecular weight 9:1, 5:5 and
1:9 ratios and grown by Zone- Refining Technique under a vacuum
atmosphere. The EDAX of these samples are done and the results are
reported. Micro hardness test has been used as an alternative test for
measuring material’s tensile properties. The effect of temperature and
load on the hardness of the grown alloy has been studied. Further the
comparative studies of work hardening coefficients are reported.