Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: This paper presents a method of hardening the 8051
micro-controller, able to assure reliable operation in the presence of
bit flips caused by radiation. Aiming at avoiding such faults in the
8051 micro-controller, Hamming code protection was used in its
SRAM memory and registers. A VHDL code has been used for this
hamming code protection.
Abstract: In this paper, some relative efficiency have been
discussed, including the LSE estimate with respect to BLUE in curve
model. Four new kinds of relative efficiency have defined, and their
upper bounds have been discussed.
Abstract: This paper presents an efficient fusion algorithm for
iris images to generate stable feature for recognition in unconstrained
environment. Recently, iris recognition systems are focused on real
scenarios in our daily life without the subject’s cooperation. Under
large variation in the environment, the objective of this paper is to
combine information from multiple images of the same iris. The
result of image fusion is a new image which is more stable for further
iris recognition than each original noise iris image. A wavelet-based
approach for multi-resolution image fusion is applied in the fusion
process. The detection of the iris image is based on Adaboost
algorithm and then local binary pattern (LBP) histogram is then
applied to texture classification with the weighting scheme.
Experiment showed that the generated features from the proposed
fusion algorithm can improve the performance for verification system
through iris recognition.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: This paper seeks to analyse the benefits of big data
and more importantly the challenges it pose to the subject of privacy
and data protection. First, the nature of big data will be briefly
deliberated before presenting the potential of big data in the present
days. Afterwards, the issue of privacy and data protection is
highlighted before discussing the challenges of implementing this
issue in big data. In conclusion, the paper will put forward the debate
on the adequacy of the existing legal framework in protecting
personal data in the era of big data.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: It is important to take security measures to protect
your computer information, reduce identify theft, and prevent from
malicious cyber-attacks. With cyber-attacks on the continuous rise,
people need to understand and learn ways to prevent from these
attacks. Cyber-attack is an important factor to be considered if one is
to be able to protect oneself from malicious attacks. Without proper
security measures, most computer technology would hinder home
users more than such technologies would help. Knowledge of how
cyber-attacks operate and protective steps that can be taken to reduce
chances of its occurrence are key to increasing these security
measures. The purpose of this paper is to inform home users on the
importance of identifying and taking preventive steps to avoid cyberattacks.
Throughout this paper, many aspects of cyber-attacks will be
discuss: what a cyber-attack is, the affects of cyber-attack for home
users, different types of cyber-attacks, methodology to prevent such
attacks; home users can take to fortify security of their computer.
Abstract: The paper deals with the diagnostics of steel roof
structure of the winter sports halls built in 1970 year. The necessity
of the diagnostics has been given by the requirement to the evaluation
design of this structure, which has been caused by the new situation
in the field of the loadings given by the validity of the European
Standards in the Czech Republic from 2010 year. Due to these
changes in the normative rules, in practice existing structures are
gradually subjected to the evaluation design and depending on its
results to the strengthening or reconstruction, respectively. Steel roof
is composed of plane truss main girders, purlins and bracings and the
roof structure is supported by two arch main girders with the span of
L = 84 m. The in situ diagnostics of the roof structure was oriented to
the following parts: (i) determination and evaluation of the actual
material properties of used steel and (ii) verification of the actual
dimensions of the structural members. For the solution the nondestructive
methods have been used for in situ measurement. For the
indicative determination of steel strengths the modified method based
on the determination of Rockwell’s hardness has been used. For the
verification of the member’s dimensions (thickness of hollow
sections) the ultrasound method has been used. This paper presents
the results obtained using these testing methods and their evaluation,
from the viewpoint of the usage for the subsequent static assessment
and design evaluation of the existing structure. For the comparison,
the examples of the similar evaluations realized for steel structures of
the stadiums in Olomouc and Jihlava cities are briefly illustrated, too.
Abstract: The restrained construction zoning, an important part
in the urban master plan, is a necessary planning tool to control the city
sprawl, to guarantee the reservation implementation of the various
types of protective elements, and to realize the storage of the essential
urban spatial resources. Simultaneously, owing to the diverse
constitutes of restrained construction area and the various stakeholders
involved in, its planning requires an overall consideration of all
elements from the perspective of coordination+, balance and
practicability to deal with the problems and conflicts in this process.
Taking Yangzijin Ecological Restrained Construction Area in
Yangzhou as an example, this study analyzes all the potential actors,
agencies and stakeholders in this restrained construction area, as well
as the relevant conflicts between each other. Besides, this study tries to
build up a planning procedure based on the framework of governance
theory, and proposes a possible planning method that combines
"rigidity" and "flexibility" to protect the ecological limitation
boundary, to take every interest into account, and to promote economic
development in a harmonious society.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: The inherent skin patterns created at the joints in the
finger exterior are referred as finger knuckle-print. It is exploited to
identify a person in a unique manner because the finger knuckle print
is greatly affluent in textures. In biometric system, the region of
interest is utilized for the feature extraction algorithm. In this paper,
local and global features are extracted separately. Fast Discrete
Orthonormal Stockwell Transform is exploited to extract the local
features. Global feature is attained by escalating the size of Fast
Discrete Orthonormal Stockwell Transform to infinity. Two features
are fused to increase the recognition accuracy. A matching distance is
calculated for both the features individually. Then two distances are
merged mutually to acquire the final matching distance. The
proposed scheme gives the better performance in terms of equal error
rate and correct recognition rate.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: Qatar, a Gulf country highly dependent on its oil and
gas revenues – is looking to innovate, diversify, and ultimately reach
its aim of creating a knowledge economy to prepare for its post-oil
era. One area that the country is investing in is Contemporary Art,
and world renowned artists such as Damien Hirst and Richard Serra –
have been commissioned to design site-specific art for the public
spaces of the city of Doha as well as in more remote desert locations.
This research discusses the changing presence, role and context of
public art in Doha, both from a historical and cultural overview, and
the different forms and media as well as the typologies of urban and
public spaces in which the art is installed. It examines the process of
implementing site-specific artworks, looking at questions of scale,
history, social meaning and formal aesthetics. The methodologies
combine theoretical research on the understanding of public art and
its role and placement in public space, as well as empirical research
on contemporary public art projects in Doha, based on documentation
and interviews and as well as site and context analysis of the urban or
architectural spaces within which the art is situated. Surveys and
interviews – using social media - in different segments of the
contemporary Qatari society, including all nationalities and social
groups, are used to measure and qualify the impacts and effects on
the population.
Abstract: In this investigation, we have evaluated the effects of
arsenic trioxide on hepatic function in pregnant and lactating Swiss
albino mice and their suckling pups. Experiments were carried out on
female mice given 175 ppm As2O3 in their drinking water from the
14th day of pregnancy until day 14 after delivery. Our results showed
a significant decrease in plasma levels of total protein and albumin,
cholesterol and triglyceride in As2O3 treated mice and their pups. The
hyperbilirubinemia and the increased plasma total alkaline
phosphatase activity suggested the presence of cholestasis.
Transaminase activities as well as lactate deshydrogenase activity in
plasma, known as biomarkers of hepatocellular injury, were elevated
indicating hepatic cells’ damage after treatment with As2O3.
Exposure to arsenic led to an increase of liver thiobarbituric acid
reactive substances level along with a concomitant decrease in the
activities of superoxide dismutase, catalase and glutathione
peroxidase and in glutathione.
Abstract: Near-infrared spectroscopy (NIRS) has been widely
used as a non-invasive method to measure brain activity, but it is
corrupted by baseline drift noise. Here we present a method to measure
regional cerebral blood flow as a derivative of NIRS output. We
investigate whether, when listening to languages, blood flow can
reasonably localize and represent regional brain activity or not. The
prefrontal blood flow distribution pattern when advanced
second-language listeners listened to a second language (L2) was most
similar to that when listening to their first language (L1) among the
patterns of mean and standard deviation. In experiments with 25
healthy subjects, the maximum blood flow was localized to the left
BA46 of advanced listeners. The blood flow presented is robust to
baseline drift and stably localizes regional brain activity.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.