Abstract: This paper presents a case study of using STATCOM to enhance the performance of Al-Qatraneh 33-kV transmission line. The location of the STATCOM was identified by maintaining minimum voltage drops at the 110 load nodes. The transmission line and the 110 load nodes have been modeled by MATLAB/Simulink. The suggested STATCOM and its location will increase the transmission capability of this transmission line and overcome the overload expected in the year 2020. The annual percentage loading rise has been considered as 14.35%. A graphical representation of the line-to-line voltages and the voltage drops at different load nodes is illustrated.
Abstract: Heat treatable aluminum alloys such as 7075 and
7055, because of high strength and low density, are used widely in
aircraft industry. For best mechanical properties, T6 heat treatment
has recommended for this regards, but this temper treatment is
sensitive to corrosion induced and Stress Corrosion Cracking (SCC)
damage. For improving this property, the over-aging treatment (T7)
applies to this alloy, but it decreases the mechanical properties up to
30 percent. Hence, to increase the mechanical properties, without any
remarkable decrease in SCC resistant, Retrogression and Re-Aging
(RRA) heat treatment is used. This treatment performs in a relatively
short time. In this paper, the RRA heat treatment was applied to 7055
aluminum alloy and then effect of RRA time on the mechanical
properties of 7055 has been investigated. The results show that the
40-minute time is suitable time for retrogression of 7055 aluminum
alloy and ultimate strength increases up to 625MPa.
Abstract: Wireless Sensor Network (WSN) routing is complex
due to its dynamic nature, computational overhead, limited battery
life, non-conventional addressing scheme, self-organization, and
sensor nodes limited transmission range. An energy efficient routing
protocol is a major concern in WSN. LEACH is a hierarchical WSN
routing protocol to increase network life. It performs self-organizing
and re-clustering functions for each round. This study proposes a
better sensor networks cluster head selection for efficient data
aggregation. The algorithm is based on Tabu search.
Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: Intermediate cities which also called medium size
cities have an important role in the process of globalization. It is
argued that, in some cases this type of cities may be depopulated or in
otherwise may be transformed as the periphery of metropolitans, so
that the personal identity of the city and its local cultural heritage
could suffer from its neighbor metropolitan. Over the last decades,
the role of tourism in the development process and the cultural
heritage has increased. The impact of tourism on socioeconomic
growth makes motivation for the study of tourism development in
regional and urban planning process. There are evidences that
tourism has a positive impact in local development and makes
economic motivations for cultural heritage protection. In this study,
by considering the role of tourism in local development, especially by
its economic and socio-cultural impacts, it is tried to introduce a
strategy for tourism development through a method of urban planning
for intermediate cities called as Base plan. Damavand is an
intermediate city located in Tehran province, Iran with a high
potential in tourism by its local specific characteristic like social
structure, antiquities and natural attractions. It’s selected as a suitable
case study for intended strategy which is a combination of urban
planning and tourism development methods. Focusing on recognition
of the historical and cultural heritage of Damavand, in this paper
through “base plan methodology” a strategy of urban planning
toward tourism development is prepared in order to make tourism
development as a support for cultural heritage of this city.
Abstract: The purposes of hydraulic gate are to maintain the
functions of storing and draining water. It bears long-term hydraulic
pressure and earthquake force and is very important for reservoir and
waterpower plant. The high tensile strength of steel plate is used as
constructional material of hydraulic gate. The cracks and rusts,
induced by the defects of material, bad construction and seismic
excitation and under water respectively, thus, the mechanics
phenomena of gate with crack are probing into the cause of stress
concentration, induced high crack increase rate, affect the safety and
usage of hydroelectric power plant. Stress distribution analysis is a
very important and essential surveying technique to analyze
bi-material and singular point problems. The finite difference
infinitely small element method has been demonstrated, suitable for
analyzing the buckling phenomena of welding seam and steel plate
with crack. Especially, this method can easily analyze the singularity
of kink crack. Nevertheless, the construction form and deformation
shape of some gates are three-dimensional system. Therefore, the
three-dimensional Digital Image Correlation (DIC) has been
developed and applied to analyze the strain variation of steel plate with
crack at weld joint. The proposed Digital image correlation (DIC)
technique is an only non-contact method for measuring the variation of
test object. According to rapid development of digital camera, the cost
of this digital image correlation technique has been reduced.
Otherwise, this DIC method provides with the advantages of widely
practical application of indoor test and field test without the restriction
on the size of test object. Thus, the research purpose of this research is
to develop and apply this technique to monitor mechanics crack
variations of weld steel hydraulic gate and its conformation under
action of loading. The imagines can be picked from real time
monitoring process to analyze the strain change of each loading stage.
The proposed 3-Dimensional digital image correlation method,
developed in the study, is applied to analyze the post-buckling
phenomenon and buckling tendency of welded steel plate with crack.
Then, the stress intensity of 3-dimensional analysis of different
materials and enhanced materials in steel plate has been analyzed in
this paper. The test results show that this proposed three-dimensional
DIC method can precisely detect the crack variation of welded steel
plate under different loading stages. Especially, this proposed DIC
method can detect and identify the crack position and the other flaws
of the welded steel plate that the traditional test methods hardly detect
these kind phenomena. Therefore, this proposed three-dimensional
DIC method can apply to observe the mechanics phenomena of
composite materials subjected to loading and operating.
Abstract: Botanical gardens are very significant organizations
which protect the environment against the increasing environmental
problems, provide environmental education for people, offer
recreation possibilities, etc. This article describes botanical gardens
and their functions. The most important function of botanical garden
is to provide environmental education for people and improve
environmental awareness. Considering this function, some botanical
gardens were examined and opinions were suggested about the
subject.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: Globally, many women are still disadvantaged when it
comes to business opportunities. Entrepreneurship development
programs, specifically designed to assist women entrepreneurs, are
assisting in solving this problem to a certain extent. The purpose of
this study is to identify the factors that motivate females to start their
own business. Females, from three different groups (2013, 2014 and
2015), who were all enrolled in a short learning program specifically
designed for women in early start-up stage or intending to start a
business, were asked what motivated them to start a business. The
results indicated that, from all three groups, the majority of the
women wanted to start a business to be independent and have
freedom and to add towards a social goal. The results further
indicated that in general, women would enter into entrepreneurship
activity due to pull factors rather than push factors.
Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: In this study, static and dynamic responses of a typical
reinforced concrete solid slab, designed to British Standard (BS 8110:
1997) and under self and live loadings for dance halls are reported.
Linear perturbation analysis using finite element method was
employed for modal, impulse loading and frequency response
analyses of the slab under the aforementioned loading condition.
Results from the static and dynamic analyses, comprising of the slab
fundamental frequencies and mode shapes, dynamic amplification
factor, maximum deflection, stress distributions among other
valuable outcomes are presented and discussed. These were gauged
with the limiting provisions in the design code with a view of
justifying valid optimization objective function for the structure that
can ensure both adequate strength and economical section for large
clear span slabs. This is necessary owing to the continued increase in
cost of erecting building structures and the squeeze on public finance
globally.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: Radio Frequency Identification (RFID) has become a
key technology in the emerging concept of Internet of Things (IoT).
Naturally, business applications would require the deployment of
various RFID systems developed by different vendors that use
different data formats and structures. This heterogeneity poses a
challenge in developing real-life IoT systems with RFID, as
integration is becoming very complex and challenging. Semantic
integration is a key approach to deal with this challenge. To do so,
ontology for RFID systems need to be developed in order to
annotated semantically RFID systems, and hence, facilitate their
integration. Accordingly, in this paper, we propose ontology for
RFID systems. The proposed ontology can be used to semantically
enrich RFID systems, and hence, improve their usage and reasoning.
Abstract: The purpose of this paper is to contribute to the
enhancement of a hydroelectric plant protection by coordinating
protection measures / existing security and introducing new measures
under a risk management process. In addition, plan identifies key
critical elements of a hydroelectric plant, from its level vulnerabilities
and threats it is subjected to in order to achieve the necessary
protection measures to reduce the level of risk.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.