Abstract: Computational study of two dimensional supersonic reacting hydrogen-air flows is performed to investigate the nitrogen effects on ignition delay time for premixed and diffusion flames. Chemical reaction is treated using detail kinetics and the advection upstream splitting method is used to calculate the numerical inviscid fluxes. The results show that just in stoichiometric condition for both premixed and diffusion flames, there is monotone dependency of the ignition delay time to the nitrogen addition. In other situations, the optimal condition from ignition viewpoint should be found using numerical investigations.
Abstract: Microtomographic images and thin section (TS)
images were analyzed and compared against some parameters of
geological interest such as porosity and its distribution along the
samples. The results show that microtomography ( CT) analysis,
although limited by its resolution, have some interesting information
about the distribution of porosity (homogeneous or not) and can also
quantify the connected and non-connected pores, i.e., total porosity.
TS have no limitations concerning resolution, but are limited by the
experimental data available in regards to a few glass sheets for
analysis and also can give only information about the connected
pores, i.e., effective porosity. Those two methods have their own
virtues and flaws but when paired together they are able to
complement one another, making for a more reliable and complete
analysis.
Abstract: In DMVC, we have more than one options of sources available for construction of side information. The newer techniques make use of both the techniques simultaneously by constructing a bitmask that determines the source of every block or pixel of the side information. A lot of computation is done to determine each bit in the bitmask. In this paper, we have tried to define areas that can only be well predicted by temporal interpolation and not by multiview interpolation or synthesis. We predict that all such areas that are not covered by two cameras cannot be appropriately predicted by multiview synthesis and if we can identify such areas in the first place, we don-t need to go through the script of computations for all the pixels that lie in those areas. Moreover, this paper also defines a technique based on KLT to mark the above mentioned areas before any other processing is done on the side view.
Abstract: We present a method to create special domain
collections from news sites. The method only requires a single
sample article as a seed. No prior corpus statistics are needed and the
method is applicable to multiple languages. We examine various
similarity measures and the creation of document collections for
English and Japanese. The main contributions are as follows. First,
the algorithm can build special domain collections from as little as
one sample document. Second, unlike other algorithms it does not
require a second “general" corpus to compute statistics. Third, in our
testing the algorithm outperformed others in creating collections
made up of highly relevant articles.
Abstract: Climate change leading to global warming affects the
earth through many different ways such as weather (temperature, precipitation, humidity and the other parameters of weather), snow coverage and ice melting, sea level rise, hydrological cycles, quality of water, agriculture, forests, ecosystems and health. One of the most
affected areas by climate change is hydrology and water resources.
Regions where majority of runoff consists of snow melt are more
sensitive to climate change. The first step of climate change studies
is to establish trends of significant climate variables including precipitation,
temperature and flow data to detect any potential climate
change impacts already happened. Two popular non-parametric trend
analysis methods, Mann-Kendal and Spearman-s Rho were applied
to Upper Euphrates Basin (Turkey) to detect trends of precipitation,
temperatures (maximum, minimum and average) and streamflow.
Abstract: Cloud computing is the innovative and leading
information technology model for enabling convenient, on-demand
network access to a shared pool of configurable computing resources
that can be rapidly provisioned and released with minimal
management effort. This paper presents our development on enabling
an individual user's desktop in a virtualized environment, which is
stored on a remote virtual machine rather than locally. We present the
initial work on the integration of virtual desktop and application
sharing with virtualization technology. Given the development of
remote desktop virtualization, this proposed effort has the potential to
positively provide an efficient, resilience and elastic environment for
online cloud service. Users no longer need to burden the cost of
software licenses and platform maintenances. Moreover, this
development also helps boost user productivity by promoting a
flexible model that lets users access their desktop environments from
virtually anywhere.
Abstract: A scaffold is necessary for tooth regeneration because of its three-dimensional geometry. For restoration of defect, it is necessary for the scaffold to be prepared in the shape of the defect. Sponges made from polyvinyl alcohol with formalin cross-linking (PVF sponge) have been used for scaffolds for bone formation in vivo. To induce osteogenesis within the sponge, methods of growing rat bone marrow cells (rBMCs) among the fiber structures in the sponge might be considered. Storage of rBMCs among the fibers in the sponge coated with dextran (10 kDa) was tried. After seeding of rBMCs to PVF sponge immersed in dextran solution at 2 g/dl concentration, osteogenesis was recognized in subcutaneously implanted PVF sponge as a scaffold in vivo. The level of osteocalcin was 25.28±5.71 ng/scaffold and that of Ca was 129.20±19.69 µg/scaffold. These values were significantly higher than those in sponges without dextran coating (p
Abstract: Recently, Genetic Algorithms (GA) and Differential
Evolution (DE) algorithm technique have attracted considerable
attention among various modern heuristic optimization techniques.
Since the two approaches are supposed to find a solution to a given
objective function but employ different strategies and computational
effort, it is appropriate to compare their performance. This paper
presents the application and performance comparison of DE and GA
optimization techniques, for flexible ac transmission system
(FACTS)-based controller design. The design objective is to enhance
the power system stability. The design problem of the FACTS-based
controller is formulated as an optimization problem and both the PSO
and GA optimization techniques are employed to search for optimal
controller parameters. The performance of both optimization
techniques has been compared. Further, the optimized controllers are
tested on a weekly connected power system subjected to different
disturbances, and their performance is compared with the
conventional power system stabilizer (CPSS). The eigenvalue
analysis and non-linear simulation results are presented and
compared to show the effectiveness of both the techniques in
designing a FACTS-based controller, to enhance power system
stability.
Abstract: As the development of digital technology is increasing,
Digital cinema is getting more spread.
However, content copy and attack against the digital cinema becomes
a serious problem. To solve the above security problem, we propose
“Additional Watermarking" for digital cinema delivery system. With
this proposed “Additional watermarking" method, we protect content
copyrights at encoder and user side information at decoder. It realizes
the traceability of the watermark embedded at encoder.
The watermark is embedded into the random-selected frames using
Hash function. Using it, the embedding position is distributed by Hash
Function so that third parties do not break off the watermarking
algorithm.
Finally, our experimental results show that proposed method is much
better than the convenient watermarking techniques in terms of
robustness, image quality and its simple but unbreakable algorithm.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: This paper outlines the research conducted to propose na framework of 'Knowledge Society' (KS) in the Malaysian context.
It is important to highlight that the emergence of KS is a result of the rapid growth in knowledge and information. However, the discussion
of KS should not only be limited to the importance of knowledge, but a holistic KS is also determined by other imperative dimensions. This
article discusses the results of a study conducted previously in Malaysia in order to identify the essential dimensions of KS, and
consequently propose a KS framework in the Malaysian context.
Two methods were employed, namely the Delphi technique and semi-structured interviews. The modified Delphi involved five
rounds with ten experts, while the interviews were conducted with two prominent figures in Malaysia. The results support the proposed
framework which contains seven major dimensions in order for Malaysia to become a KS in the future. The dimensions which are
crucial for a holistic Malaysian KS are human capital, spirituality, economy, social, institutional, sustainability, and driven by the ICT.
Abstract: This paper presents a real time force sensing instrument that is designed for human gait analysis purposes. This instrument mainly consists of three main elements: the force sensing mat, signal conditioning and switching circuit and data acquisition
device. In order to control and to process the incoming signals from the force sensing mat, Force-Logger and Force-Reloader program are
developed using Labview 8.0. This paper describes the architecture of the force sensing mat, signal conditioning and switching circuit and the real time streaming of the incoming data from the force
sensing mat.
Abstract: In this paper, an analysis is presented, which
demonstrates the effect pre-logic factoring could have on an
automated combinational logic synthesis process succeeding it. The
impact of pre-logic factoring for some arbitrary combinatorial
circuits synthesized within a FPGA based logic design environment
has been analyzed previously. This paper explores a similar effect,
but with the non-regenerative logic synthesized using elements of a
commercial standard cell library. On an overall basis, the results
obtained pertaining to the analysis on a variety of MCNC/IWLS
combinational logic benchmark circuits indicate that pre-logic
factoring has the potential to facilitate simultaneous power, delay and
area optimized synthesis solutions in many cases.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.
Abstract: Energy intensity(energy consumption intensity) is a
global index which computes the required energy for producing a
specific value of goods and services in each country. It is computed
in terms of initial energy supply or final energy consumption. In this
study (research) Divisia method is used to decompose energy
consumption and energy intensity. This method decomposes
consumption and energy intensity to production effects, structural
and net intensity and could be done as time series or two-periodical.
This study analytically investigates consumption changes and energy
intensity on economical sectors of Iran and more specific on road
transportation(rail road and road).Our results show that the
contribution of structural effect (change in economical activities
combination) is very low and the effect of net energy consumption
has the higher contribution in consumption changes and energy
intensity. In other words, the high consumption of energy is due to
Intensity of energy consumption and is not to structural effect of
transportation sector.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. The CAD (Computer Aided Diagnosis ) of lung CT
generally first segment the area of interest (lung) and then analyze
the separately obtained area for nodule detection in order to
diagnosis the disease. For normal lung, segmentation can be
performed by making use of excellent contrast between air and
surrounding tissues. However this approach fails when lung is
affected by high density pathology. Dense pathologies are present in
approximately a fifth of clinical scans, and for computer analysis
such as detection and quantification of abnormal areas it is vital that
the entire and perfectly lung part of the image is provided and no
part, as present in the original image be eradicated. In this paper we
have proposed a lung segmentation technique which accurately
segment the lung parenchyma from lung CT Scan images. The
algorithm was tested against the 25 datasets of different patients
received from Ackron Univeristy, USA and AGA Khan Medical
University, Karachi, Pakistan.
Abstract: Local Linear Neuro-Fuzzy Models (LLNFM) like other neuro- fuzzy systems are adaptive networks and provide robust learning capabilities and are widely utilized in various applications such as pattern recognition, system identification, image processing and prediction. Local linear model tree (LOLIMOT) is a type of Takagi-Sugeno-Kang neuro fuzzy algorithm which has proven its efficiency compared with other neuro fuzzy networks in learning the nonlinear systems and pattern recognition. In this paper, a dedicated reconfigurable and parallel processing hardware for LOLIMOT algorithm and its applications are presented. This hardware realizes on-chip learning which gives it the capability to work as a standalone device in a system. The synthesis results on FPGA platforms show its potential to improve the speed at least 250 of times faster than software implemented algorithms.
Abstract: This paper highlights the importance of integrating social and technical approach (which is so called a “hybrid socio-technical approach") as one innovative and strategic program to support the social development in geodisaster prone area in Indonesia. Such program mainly based on public education and community participation as a partnership program by the University, local government and may also with the private company and/ or local NGO. The indigenous, simple and low cost technology has also been introduced and developed as a part of the hybrid sociotechnical system, in order to ensure the life and environmental protection, with respect to the sustainable human and social development.