Abstract: In this paper, a variable multiple dependent state (MDS) sampling plan is developed based on the process capability index using Bayesian approach. The optimal parameters of the developed sampling plan with respect to constraints related to the risk of consumer and producer are presented. Two comparison studies have been done. First, the methods of double sampling model, sampling plan for resubmitted lots and repetitive group sampling (RGS) plan are elaborated and average sample numbers of the developed MDS plan and other classical methods are compared. A comparison study between the developed MDS plan based on Bayesian approach and the exact probability distribution is carried out.
Abstract: The objective of the present study was to determine the polymorphism in the leptin (332G>A) and its association with biometric traits in Sanjabi sheep. For this purpose, blood samples from 96 rams were taken, and tail length, width tail, circumference tail, body length, body width, and height were simultaneously recorded. PCR was performed using specific primer to amplify 463 bp fragment including exon 3 of leptin gene, and PCR products were digested by Cail restriction enzymes. The 332G>A (at 332th nucleotide of exon 3 leptin gene) that caused an amino acid change from Arg to Gln was detected by Cail (CAGNNNCTG) endonuclease, as the endonuclease cannot cut this region if G nucleotide is located in this position. Three genotypes including GG (463), GA (463, 360and 103 bp) and GG (360 bp and 103 bp) were identified after digestion by enzyme. The estimated frequencies of three genotypes including GG, GA, and AA for 332G>A locus were 0.68, 0.29 and 0.03 and those were 0.18 and 0.82 for A and G alleles, respectively. In the current study, chi-square test indicated that 332G>A positions did not deviate from the Hardy–Weinberg (HW) equilibrium. The most important reason to show HW equation was that samples used in this study belong to three large local herds with a traditional breeding system having random mating and without selection. Shannon index amount was calculated which represent an average genetic variation in Sanjabi rams. Also, heterozygosity estimated by Nei index indicated that genetic diversity of mutation in the leptin gene is moderate. Leptin gene polymorphism in the 332G>A had significant effect on body length (P0.05). This non-synonymous SNP resulted in different amino acid changes at codon positions111(R/Q). As leptin activity is localized, at least in part, in domains between amino acid residues 106-1406, it is speculated that the detected SNP at position 332 may affect the activity of leptin and may lead to different biological functions. Based to our results, due to significant effect of leptin gene polymorphism on body size traits, this gene may be used a candidate gene for improving these traits.
Abstract: The high purity rare earth elements (REEs) have been vastly used in the field of chemical engineering, metallurgy, nuclear energy, optical, magnetic, luminescence and laser materials, superconductors, ceramics, alloys, catalysts, and etc. Neodymium is one of the most abundant rare earths. By development of a neodymium–iron–boron (Nd–Fe–B) permanent magnet, the importance of neodymium has dramatically increased. Solvent extraction processes have many operational limitations such as large inventory of extractants, loss of solvent due to the organic solubility in aqueous solutions, volatilization of diluents, etc. One of the promising methods of liquid membrane processes is emulsion liquid membrane (ELM) which offers an alternative method to the solvent extraction processes. In this work, a study on Nd extraction through multi-walled carbon nanotubes (MWCNTs) assisted ELM using response surface methodology (RSM) has been performed. The ELM composed of diisooctylphosphinic acid (CYANEX 272) as carrier, MWCNTs as nanoparticles, Span-85 (sorbitan triooleate) as surfactant, kerosene as organic diluent and nitric acid as internal phase. The effects of important operating variables namely, surfactant concentration, MWCNTs concentration, and treatment ratio were investigated. Results were optimized using a central composite design (CCD) and a regression model for extraction percentage was developed. The 3D response surfaces of Nd(III) extraction efficiency were achieved and significance of three important variables and their interactions on the Nd extraction efficiency were found out. Results indicated that introducing the MWCNTs to the ELM process led to increasing the Nd extraction due to higher stability of membrane and mass transfer enhancement. MWCNTs concentration of 407 ppm, Span-85 concentration of 2.1 (%v/v) and treatment ratio of 10 were achieved as the optimum conditions. At the optimum condition, the extraction of Nd(III) reached the maximum of 99.03%.
Abstract: The aim of this research was to calculate the
mechanical properties of Pd3Rh and PdRh3 ordered alloys. The
molecular dynamics (MD) simulation technique was used to obtain
temperature dependence of the energy, the Yong modulus, the shear
modulus, the bulk modulus, Poisson-s ratio and the elastic stiffness
constants at the isobaric-isothermal (NPT) ensemble in the range of
100-325 K. The interatomic potential energy and force on atoms were
calculated by Quantum Sutton-Chen (Q-SC) many body potential.
Our MD simulation results show the effect of temperature on the
cohesive energy and mechanical properties of Pd3Rh as well as
PdRh3 alloys. Our computed results show good agreement with the
experimental results where they have been available.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: In the present research, the titanium-catalyzed
ethylene dimerization and more specifically, the concomitant byproducts
and polymer formation have been studied in the presence of 2,5-dimethoxytetrahydrofuran as an electron donor compound in the
combination with triethylaluminium (TEA) as activator. Then, we
added ethylene chlorobromide as a new efficient promoter to the
relevant catalyst system. Finally, the behavior of novel homogeneous
[Titanium tetrabutoxide (Ti(OC4H9)4)/2,5-dimethoxytetrahydrofuran/
TEA/ethylene chlorobromide] was investigated in the various
operating conditions for the optimum production of 1-butene. In the
optimum conditions, a very high ethylene conversion (almost 90.77
%), a relative high selectivity to 1-butene (79.00 %), yield of reaction equal to 71.70 % and a significant productivity (turnover frequency
equal to 1370 h-1) were achieved.
Abstract: Dehydration process was carried out for tomato slices of var. Avinash after giving different pre-treatments such as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl). Untreated samples served as control. Solar drier and continuous conveyor (tunnel) drier were used for dehydration. Quality characteristics of tomato slices viz. moisture content, sugar, titratable acidity, lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning as affected by dehydration process were studied. Storage study was also carried out for a period of six months for tomato powder packed into different types of packaging materials viz. metalized polyester (MP) film and low density poly ethylene (LDPE). Changes in lycopene content and non-enzymatic browning (NEB) were estimated during storage at room temperature. Pretreatment of 5 mm thickness of tomato slices with calcium chloride in combination with potassium metabisulphite and drying using a tunnel drier with subsequent storage of product in metalized polyester bags was selected as the best process.
Abstract: The usefulness of weaning foods to meet the nutrient
needs of children is well recognized, and most of them are precooked
roller dried mixtures of cereal and/or legume flours which posses a
high viscosity and bulk when reconstituted. The objective of this study
was to formulate composite weaning foods using cereals, malted
legumes and vegetable powders and analyze them for nutrients,
functional properties and sensory attributes. Selected legumes (green
gram and lentil) were germinated, dried and dehulled. Roasted wheat,
rice, carrot powder and skim milk powder also were used. All the
ingredients were mixed in different proportions to get four
formulations, made into 30% slurry and dried in roller drier. The
products were analyzed for proximate principles, mineral content,
functional and sensory qualities. The results of analysis showed
following range of constituents per 100g of formulations on dry
weight basis, protein, 18.1-18.9 g ; fat, 0.78-1.36 g ; iron, 5.09-6.53
mg; calcium, 265-310 mg. The lowest water absorption capacity was
in case of wheat green gram based and the highest was in rice lentil
based sample. Overall sensory qualities of all foods were graded as
“good" and “very good" with no significant differences. The results
confirm that formulated weaning foods were nutritionally superior,
functionally appropriate and organoleptically acceptable.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: This study investigated the use of modified
atmosphere packaging (MAP) and different packaging to extend the
shelf life of Barbari flat bread. Three atmospheres including 70%CO2
and 30%N2, 50% CO2 and 50%N2 and a normal air as control were
used. The bread samples were packaged in three type pouches. The
shelf life was determined by appearance of mold and yeast (M +Y) in
Barbari bread samples stored at 25 ± 1°C and 38 ± 2% relative
humidity. The results showed that it is possible to prolong the shelf
life of Barbari bread from four days to about 21 days by using
modified atmosphere packaging with high carbon dioxide
concentration and high-barrier laminated and vacuum bags packages.
However, the hardness of samples kept in MAP increase significantly
by increase of carbon dioxide concentration. The correlation
coefficient (r) between headspace CO2 concentration and hardness
was 0.997, 0.997 and 0.599 for A, B and C packaging respectively.
High negative correlation coefficients were found between the crumb
moisture and the hardness values in various packaging. There were
significant negative correlation coefficients between sensory
parameters and hardness of texture.
Abstract: This paper proposes new hybrid approaches for face
recognition. Gabor wavelets representation of face images is an
effective approach for both facial action recognition and face
identification. Perform dimensionality reduction and linear
discriminate analysis on the down sampled Gabor wavelet faces can
increase the discriminate ability. Nearest feature space is extended to
various similarity measures. In our experiments, proposed Gabor
wavelet faces combined with extended neural net feature space
classifier shows very good performance, which can achieve 93 %
maximum correct recognition rate on ORL data set without any preprocessing
step.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: The effect of teaching method on learning
assistance Dunn Review .The study, to compare the effects of
collaboration on teaching mathematics learning courses, including
writing, science, experimental girl students by other methods of
teaching basic first paid and the amount of learning students
methods have been trained to cooperate with other students with
other traditional methods have been trained to compare. The
survey on 100 students in Tehran that using random sampling ¬
cluster of girl students between the first primary selections was
performed. Considering the topic of semi-experimental research
methods used to practice the necessary information by
questionnaire, examination questions by the researcher, in
collaboration with teachers and view authority in this field and
related courses that teach these must have been collected.
Research samples to test and control groups were divided.
Experimental group and control group collaboration using
traditional methods of mathematics courses, including writing and
experimental sciences were trained. Research results using
statistical methods T is obtained in two independent groups show
that, through training assistance will lead to positive results and
student learning in comparison with traditional methods, will
increase also led to collaboration methods increase skills to solve
math lesson practice, better understanding and increased skill
level of students in practical lessons such as science and has been
writing.
Abstract: Bode stability analysis based on transmission line
modeling (TLM) for single wall carbon nanotube (SWCNT)
interconnects used in 3D-VLSI circuits is investigated for the first
time. In this analysis, the dependence of the degree of relative
stability for SWCNT interconnects on the geometry of each tube has
been acquired. It is shown that, increasing the length and diameter of
each tube, SWCNT interconnects become more stable.
Abstract: The permanent magnet synchronous motor (PMSM) is
very useful in many applications. Vector control of PMSM is popular
kind of its control. In this paper, at first an optimal vector control for
PMSM is designed and then results are compared with conventional
vector control. Then, it is assumed that the measurements are noisy
and linear quadratic Gaussian (LQG) methodology is used to filter
the noises. The results of noisy optimal vector control and filtered
optimal vector control are compared to each other. Nonlinearity of
PMSM and existence of inverter in its control circuit caused that the
system is nonlinear and time-variant. With deriving average model,
the system is changed to nonlinear time-invariant and then the
nonlinear system is converted to linear system by linearization of
model around average values. This model is used to optimize vector
control then two optimal vector controls are compared to each other.
Simulation results show that the performance and robustness to noise
of the control system has been highly improved.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: Because of the reservoir effect, dynamic analysis of concrete dams is more involved than other common structures. This problem is mostly sourced by the differences between reservoir water, dam body and foundation material behaviors. To account for the reservoir effect in dynamic analysis of concrete gravity dams, two methods are generally employed. Eulerian method in reservoir modeling gives rise to a set of coupled equations, whereas in Lagrangian method, the same equations for dam and foundation structure are used. The Purpose of this paper is to evaluate and study possible advantages and disadvantages of both methods. Specifically, application of the above methods in the analysis of dam-foundationreservoir systems is leveraged to calculate the hydrodynamic pressure on dam faces. Within the frame work of dam- foundationreservoir systems, dam displacement under earthquake for various dimensions and characteristics are also studied. The results of both Lagrangian and Eulerian methods in effects of loading frequency, boundary condition and foundation elasticity modulus are quantitatively evaluated and compared. Our analyses show that each method has individual advantages and disadvantages. As such, in any particular case, one of the two methods may prove more suitable as presented in the results section of this study.
Abstract: In the way of growing and developing firms especially
high-tech firms, on many occasions manager of firm is mainly involved in solving problems of his business and decision making about executive activities of the firm, while besides executive
measures, attention to planning of firm's success and growth way and
application of long experience and sagacity in designing business model are vital and necessary success in a business is achieved as a
result of different factors, one of the most important of them is designing and performing an optimal business model at the beginning
of the firm's work. This model is determining the limit of profitability
achieved by innovation and gained value added. Therefore, business
model is the process of connecting innovation environment and
technology with economic environment and business and is important
for succeeding modern businesses considering their traits.
Abstract: One of the most common practices for strengthening
the reinforced concrete structures is the application of FRP (Fiber
Reinforce Plastic) sheets to increase the flexural and shear strengths
of the member. The elastic modulus of FRP is considerably higher
than that of concrete. This will result in debonding between the FRP
sheets and concrete surface. With conventional surface preparation of
concrete, the ultimate capacity of the FRP sheets can hardly be
achieved. New methods for preparation of the bonding surface have
shown improvements in reducing the premature debonding of FRP
sheets from concrete surface. The present experimental study focuses
on the application of grooving method to postpone debonding of the
FRP sheets attached to the side faces of concrete beams for shear
strengthening. Comparison has also been made with conventional
surface preparation method. This study clearly shows the efficiency
of grooving method compared to surface preparation method, in
preventing the debonding phenomenon and in increasing the load
carrying capacity of FRP.