Abstract: TUSAT is a prospective Turkish
Communication Satellite designed for providing mainly data
communication and broadcasting services through Ku-Band
and C-Band channels. Thermal control is a vital issue in
satellite design process. Therefore, all satellite subsystems and
equipments should be maintained in the desired temperature
range from launch to end of maneuvering life. The main
function of the thermal control is to keep the equipments and
the satellite structures in a given temperature range for various
phases and operating modes of spacecraft during its lifetime.
This paper describes the thermal control design which uses
passive and active thermal control concepts. The active
thermal control is based on heaters regulated by software via
thermistors. Alternatively passive thermal control composes of
heat pipes, multilayer insulation (MLI) blankets, radiators,
paints and surface finishes maintaining temperature level of
the overall carrier components within an acceptable value.
Thermal control design is supported by thermal analysis using
thermal mathematical models (TMM).
Abstract: Least Significant Bit (LSB) technique is the earliest
developed technique in watermarking and it is also the most simple,
direct and common technique. It essentially involves embedding the
watermark by replacing the least significant bit of the image data with
a bit of the watermark data. The disadvantage of LSB is that it is not
robust against attacks. In this study intermediate significant bit (ISB)
has been used in order to improve the robustness of the watermarking
system. The aim of this model is to replace the watermarked image
pixels by new pixels that can protect the watermark data against
attacks and at the same time keeping the new pixels very close to the
original pixels in order to protect the quality of watermarked image.
The technique is based on testing the value of the watermark pixel
according to the range of each bit-plane.
Abstract: In the present work, we propose a new technique to
enhance the learning capabilities and reduce the computation
intensity of a competitive learning multi-layered neural network
using the K-means clustering algorithm. The proposed model use
multi-layered network architecture with a back propagation learning
mechanism. The K-means algorithm is first applied to the training
dataset to reduce the amount of samples to be presented to the neural
network, by automatically selecting an optimal set of samples. The
obtained results demonstrate that the proposed technique performs
exceptionally in terms of both accuracy and computation time when
applied to the KDD99 dataset compared to a standard learning
schema that use the full dataset.
Abstract: This paper simulates the ad-hoc mesh network in rural areas, where such networks receive great attention due to their cost, since installing the infrastructure for regular networks in these areas is not possible due to the high cost. The distance between the communicating nodes is the most obstacles that the ad-hoc mesh network will face. For example, in Terranet technology, two nodes can communicate if they are only one kilometer far from each other. However, if the distance between them is more than one kilometer, then each node in the ad-hoc mesh networks has to act as a router that forwards the data it receives to other nodes. In this paper, we try to find the critical number of nodes which makes the network fully connected in a particular area, and then propose a method to enhance the intermediate node to accept to be a router to forward the data from the sender to the receiver. Much work was done on technological changes on peer to peer networks, but the focus of this paper will be on another feature which is to find the minimum number of nodes needed for a particular area to be fully connected and then to enhance the users to switch on their phones and accept to work as a router for other nodes. Our method raises the successful calls to 81.5% out of 100% attempt calls.
Abstract: In this paper, a simple active contour based visual
tracking algorithm is presented for outdoor AGV application which is
currently under development at the USM robotic research group
(URRG) lab. The presented algorithm is computationally low cost
and able to track road boundaries in an image sequence and can
easily be implemented on available low cost hardware. The proposed
algorithm used an active shape modeling using the B-spline
deformable template and recursive curve fitting method to track the
current orientation of the road.
Abstract: Ultrathin (UTD) and Nanoscale (NSD) SOI-MOSFET devices, sharing a similar W/L but with a channel thickness of 46nm and 1.6nm respectively, were fabricated using a selective “gate recessed” process on the same silicon wafer. The electrical transport characterization at room temperature has shown a large difference between the two kinds of devices and has been interpreted in terms of a huge unexpected series resistance. Electrical characteristics of the Nanoscale device, taken in the linear region, can be analytically derived from the ultrathin device ones. A comparison of the structure and composition of the layers, using advanced techniques such as Focused Ion Beam (FIB) and High Resolution TEM (HRTEM) coupled with Energy Dispersive X-ray Spectroscopy (EDS), contributes an explanation as to the difference of transport between the devices.
Abstract: A method and apparatus for noninvasive measurement
of blood glucose concentration based on transilluminated laser beam
via the Index Finger has been reported in this paper. This method
depends on atomic gas (He-Ne) laser operating at 632.8nm
wavelength. During measurement, the index finger is inserted into the
glucose sensing unit, the transilluminated optical signal is converted
into an electrical signal, compared with the reference electrical
signal, and the obtained difference signal is processed by signal
processing unit which presents the results in the form of blood
glucose concentration. This method would enable the monitoring
blood glucose level of the diabetic patient continuously, safely and
noninvasively.
Abstract: Wind farms (WFs) with high level of penetration are
being established in power systems worldwide more rapidly than
other renewable resources. The Independent System Operator (ISO),
as a policy maker, should propose appropriate places for WF
installation in order to maximize the benefits for the investors. There
is also a possibility of congestion relief using the new installation of
WFs which should be taken into account by the ISO when proposing
the locations for WF installation. In this context, efficient wind farm
(WF) placement method is proposed in order to reduce burdens on
congested lines. Since the wind speed is a random variable and load
forecasts also contain uncertainties, probabilistic approaches are used
for this type of study. AC probabilistic optimal power flow (P-OPF)
is formulated and solved using Monte Carlo Simulations (MCS). In
order to reduce computation time, point estimate methods (PEM) are
introduced as efficient alternative for time-demanding MCS.
Subsequently, WF optimal placement is determined using generation
shift distribution factors (GSDF) considering a new parameter
entitled, wind availability factor (WAF). In order to obtain more
realistic results, N-1 contingency analysis is employed to find the
optimal size of WF, by means of line outage distribution factors
(LODF). The IEEE 30-bus test system is used to show and compare
the accuracy of proposed methodology.
Abstract: The quest of providing more secure identification
system has led to a rise in developing biometric systems. Dorsal
hand vein pattern is an emerging biometric which has attracted the
attention of many researchers, of late. Different approaches have
been used to extract the vein pattern and match them. In this work,
Principle Component Analysis (PCA) which is a method that has
been successfully applied on human faces and hand geometry is
applied on the dorsal hand vein pattern. PCA has been used to obtain
eigenveins which is a low dimensional representation of vein pattern
features. Low cost CCD cameras were used to obtain the vein
images. The extraction of the vein pattern was obtained by applying
morphology. We have applied noise reduction filters to enhance the
vein patterns. The system has been successfully tested on a database
of 200 images using a threshold value of 0.9. The results obtained are
encouraging.
Abstract: The atmospheric pressure plasma torch with a direct
current arc discharge stabilized by water vapor vortex was
experimentally investigated. Overheated up to 450K water vapor was
used as plasma forming gas. Plasma torch design is one of the most
important factors leading to a stable operation of the device. The
electrical and thermal characteristics of the plasma torch were
determined during the experimental investigations. The design and
the basic characteristics of the water vapor plasma torch are presented
in the paper.
Plasma torches with the electric arc stabilized by water vapor
vortex provide special performance characteristics in some plasma
processing applications such as thermal plasma neutralization and
destruction of organic wastes enabling to extract high caloric value
synthesis gas as by-product of the process. Syngas could be used as a
surrogate fuel partly replacing the dependence on the fossil fuels or
used as a feedstock for hydrogen, methanol production.
Abstract: This paper presents the results of a comprehensive
investigation of five blackouts that occurred on 28 August to 8
September 2011 due to bushing failures of the 132/33 kV, 125 MVA
transformers at JBB Ali Grid station. The investigation aims to
explore the root causes of the bushing failures and come up with
recommendations that help in rectifying the problem and avoiding the
reoccurrence of similar type of incidents. The incident reports about
the failed bushings and the SCADA reports at this grid station were
examined and analyzed. Moreover, comprehensive power quality
field measurements at ten 33/11 kV substations (S/Ss) in JBB Ali
area were conducted, and frequency scans were performed to verify
any harmonic resonance frequencies due to power factor correction
capacitors. Furthermore, the daily operations of the on-load tap
changers (OLTCs) of both the 125 MVA and 20 MVA transformers
at JBB Ali Grid station have been analyzed. The investigation
showed that the five bushing failures were due to a local problem, i.e.
internal degradation of the bushing insulation. This has been
confirmed by analyzing the time interval between successive OLTC
operations of the faulty grid transformers. It was also found that
monitoring the number of OLTC operations can help in predicting
bushing failure.
Abstract: In this paper, a new efficient method for load balancing in low voltage distribution systems is presented. The proposed method introduces an improved Leap-frog method for optimization. The proposed objective function includes the difference between three phase currents, as well as two other terms to provide the integer property of the variables; where the latter are the status of the connection of loads to different phases. Afterwards, a new algorithm is supplemented to undertake the integer values for the load connection status. Finally, the method is applied to different parts of Tabriz low voltage network, where the results have shown the good performance of the proposed method.
Abstract: In this study, inhibition of Microcystis aeruginosa by
antialgal alleochemical gramine, was studied by analyzing algal
metabolic activity (represented by esterase and total dehydrogenase
activities) and cell ultrastructure (showing morphological and
ultrastructure alterations using transmission electron microscopy and
DNA ladder analysis). After gramine exposure, esterase and total
dehydrogenase activities were increased firstly but decreased later. In
contrast with the controls, the cells exposed to gramine showed
apparent ultrastructure alterations with thylakoids in breakage,
phycobilins in decrease, lipid and cyanophycin granules abundant
firstly but dissolved afterwards, DNA in fragementation. The
occurrence of increase of metabolic activity and specific granules
reflected that the resistance of cellular response to gramine was
initiated. DNA fragementation associated with the increase of
metabolic activity and specific granules hinted that gramine caused M.
aeruginosa cells to initiate some morphotype of programmed cell
death.
Abstract: The regulatory competence of blood glucose homeostasis might determine the degree of academic performance. The aim of this study was to produce a model of students' alcohol use based on glucose homeostasis control and cognitive functions that might define the pathogenetic mechanism of alcohol's effect on academic performance. The study took six hours and thirty minutes on fasting, involving thirteen male students. Disturbances in cognitive functions, precisely a decrease in the effectiveness of active attention and a faster development of fatigue after four to six hours of mental work in alcohol users, compared to abstainers was statistically proven. These disturbances in alcohol users were retained even after seven to ten days of moderate alcohol use and might be the reason for the low academic performances among students who use alcoholic beverages.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: This paper presents Faults Forecasting System (FFS)
that utilizes statistical forecasting techniques in analyzing process
variables data in order to forecast faults occurrences. FFS is
proposing new idea in detecting faults. Current techniques used in
faults detection are based on analyzing the current status of the
system variables in order to check if the current status is fault or not.
FFS is using forecasting techniques to predict future timing for faults
before it happens. Proposed model is applying subset modeling
strategy and Bayesian approach in order to decrease dimensionality
of the process variables and improve faults forecasting accuracy. A
practical experiment, designed and implemented in Okayama
University, Japan, is implemented, and the comparison shows that
our proposed model is showing high forecasting accuracy and
BEFORE-TIME.
Abstract: In this paper first, Two buildings have been modeled
and then analyzed using nonlinear static analysis method under two
different conditions in Nonlinear SAP 2000 software. In the first
condition the interaction of soil adjacent to the walls of basement are
ignored while in the second case this interaction have been modeled
using Gap elements of nonlinear SAP2000 software. Finally,
comparing the results of two models, the effects of soil-structure on
period, target point displacement, internal forces, shape deformations
and base shears have been studied. According to the results, this
interaction has always increased the base shear of buildings,
decreased the period of structure and target point displacement, and
often decreased the internal forces and displacements.
Abstract: The paper presents a part of the results obtained in a
complex research project on Romanian Grey Steppe breed, owner of
some remarkable qualities such as hardiness, longevity, adaptability,
special resistance to ban weather and diseases and included in the
genetic fund (G.D. no. 822/2008.) from Romania.
Following the researches effectuated, we identified alleles of six
loci, codifying the six types of major milk proteins: alpha-casein S1
(α S1-cz); beta-casein (β-cz); kappa-casein (K-cz); beta-lactoglobulin
(β-lg); alpha-lactalbumin (α-la) and alpha-casein S2 (α S2-cz). In
system αS1-cz allele αs1-Cn B has the highest frequency (0.700), in
system β-cz allele β-Cn A2 ( 0.550 ), in system K-cz allele k-CnA2 (
0.583 ) and heterozygote genotype AB ( 0.416 ) and BB (0.375), in
system β-lg allele β-lgA1 has the highest frequency (0.542 ) and
heterozygote genotype AB ( 0.500 ), in system α-la there is
monomorphism for allele α-la B and similarly in system αS2-cz for
allele αs2-Cn A.
The milk analysis by the isoelectric focalization technique (I.E.F.)
allowed the identification of a new allele for locus αS1-casein, for two
of the individuals under analysis, namely allele called αS1-casein
IRV. When experiments were repeated, we noticed that this is not a
proteolysis band and it really was a new allele that has not been
registered in the specialized literature so far. We identified two
heterozygote individuals, carriers of this allele, namely: BIRV and
CIRV. This discovery is extremely important if focus is laid on the
national genetic patrimony.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: This paper proposes new algorithms for the computeraided
design and manufacture (CAD/CAM) of 3D woven multi-layer
textile structures. Existing commercial CAD/CAM systems are often
restricted to the design and manufacture of 2D weaves. Those
CAD/CAM systems that do support the design and manufacture of
3D multi-layer weaves are often limited to manual editing of design
paper grids on the computer display and weave retrieval from stored
archives. This complex design activity is time-consuming, tedious
and error-prone and requires considerable experience and skill of a
technical weaver. Recent research reported in the literature has
addressed some of the shortcomings of commercial 3D multi-layer
weave CAD/CAM systems. However, earlier research results have
shown the need for further work on weave specification, weave
generation, yarn path editing and layer binding. Analysis of 3D
multi-layer weaves in this research has led to the design and
development of efficient and robust algorithms for the CAD/CAM of
3D woven multi-layer textile structures. The resulting algorithmically
generated weave designs can be used as a basis for lifting plans that
can be loaded onto looms equipped with electronic shedding
mechanisms for the CAM of 3D woven multi-layer textile structures.