Abstract: Since large power transformers are the most
expensive and strategically important components of any power
generator and transmission system, their reliability is crucially
important for the energy system operation. Also, Circuit breakers are
very important elements in the power transmission line so monitoring
the events gives a knowledgebase to determine time to the next
maintenance. This paper deals with the introduction of the
comparative method of the state estimation of transformers and
Circuit breakers using continuous monitoring of voltage, current.
This paper gives details a new method based on wavelet to apparatus
insulation monitoring. In this paper to insulation monitoring of
transformer, a new method based on wavelet transformation and
neutral point analysis is proposed. Using the EMTP tools, fault in
transformer winding and the detailed transformer winding model
were simulated. The current of neutral point of winding was analyzed
by wavelet transformation. It is shown that the neutral current of the
transformer winding has useful information about fault in insulation
of the transformer.
Abstract: In aerospace applications, interactions of airflow with
aircraft structures can result in undesirable structural deformations.
This structural deformation in turn, can be predicted if the natural
modes of the structure are known. This can be achieved through
conventional modal testing that requires a known excitation force in
order to extract these dynamic properties. This technique can be
experimentally complex because of the need for artificial excitation
and it is also does not represent actual operational condition. The
current work presents part of research work that address the practical
implementation of operational modal analysis (OMA) applied to a
cantilevered hybrid composite plate employing single contactless
sensing system via laser vibrometer. OMA technique extracts the
modal parameters based only on the measurements of the dynamic
response. The OMA results were verified with impact hammer modal
testing and good agreement was obtained.
Abstract: Rapid progress in process automation and tightening
quality standards result in a growing demand being placed on fault
detection and diagnostics methods to provide both speed and
reliability of motor quality testing. Doubly fed induction generators
are used mainly for wind energy conversion in MW power plants.
This paper presents a detection of an inter turn stator and an open
phase faults, in a doubly fed induction machine whose stator and
rotor are supplied by two pulse width modulation (PWM) inverters.
The method used in this article to detect these faults, is based on
Park-s Vector Approach, using a neural network.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Nowadays, the demand for high product quality
focuses extensive attention to the quality of machined surface. The
(CNC) milling machine facilities provides a wide variety of
parameters set-up, making the machining process on the glass
excellent in manufacturing complicated special products compared to
other machining processes. However, the application of grinding
process on the CNC milling machine could be an ideal solution to
improve the product quality, but adopting the right machining
parameters is required. In glass milling operation, several machining
parameters are considered to be significant in affecting surface
roughness. These parameters include the lubrication pressure, spindle
speed, feed rate and depth of cut. In this research work, a fuzzy logic
model is offered to predict the surface roughness of a machined
surface in glass milling operation using CBN grinding tool. Four
membership functions are allocated to be connected with each input
of the model. The predicted results achieved via fuzzy logic model
are compared to the experimental result. The result demonstrated
settlement between the fuzzy model and experimental results with the
93.103% accuracy.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.
Abstract: In the present research, a finite element model is
presented to study the geometrical and material nonlinear behavior of
reinforced concrete plane frames considering soil-structure
interaction. The nonlinear behaviors of concrete and reinforcing steel
are considered both in compression and tension up to failure. The
model takes account also for the number, diameter, and distribution
of rebar along every cross section. Soil behavior is taken into
consideration using four different models; namely: linear-, nonlinear
Winkler's model, and linear-, nonlinear continuum model. A
computer program (NARC) is specially developed in order to
perform the analysis. The results achieved by the present model show
good agreement with both theoretical and experimental published
literature. The nonlinear behavior of a rectangular frame resting on
soft soil up to failure using the proposed model is introduced for
demonstration.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: Several methods have been proposed for color image
compression but the reconstructed image had very low signal to noise
ratio which made it inefficient. This paper describes a lossy
compression technique for color images which overcomes the
drawbacks. The technique works on spatial domain where the pixel
values of RGB planes of the input color image is mapped onto two
dimensional planes. The proposed technique produced better results
than JPEG2000, 2DPCA and a comparative study is reported based
on the image quality measures such as PSNR and MSE.Experiments
on real time images are shown that compare this methodology with
previous ones and demonstrate its advantages.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: A water surface slope limiting scheme is tested and
compared with the water depth slope limiter for the solution of one
dimensional shallow water equations with bottom slope source term.
Numerical schemes based on the total variation diminishing Runge-
Kutta discontinuous Galerkin finite element method with slope
limiter schemes based on water surface slope and water depth are
used to solve one-dimensional shallow water equations. For each
slope limiter, three different Riemann solvers based on HLL, LF, and
Roe flux functions are used. The proposed water surface based slope
limiter scheme is easy to implement and shows better conservation
property compared to the slope limiter based on water depth. Of the
three flux functions, the Roe approximation provides the best results
while the LF function proves to be least suitable when used with
either slope limiter scheme.
Abstract: ICT and supply chain management (SCM) are two
notions, which have attracted much attention among both
academicians and practitioners during the last decade. However, the
discussion of the relationship between the two notions has been
limited and fragmented. In this paper, we will present a summary of
the discussion of ICT components and SCM on an extensive
literature review. Then, we will discuss the interrelation between ICT
and SCM from some major components and applications of ICT
perspective. After all, we can introduce e-SCM concept, that arisen
recently in management literature, in order to cover the whole topic.
The authors look at all of the major components of electronic supply
chain management and demonstrate that the future holds tremendous
opportunity for those firms that take advantage of all of its
possibilities.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: In this paper we propose a novel RF LDMOS structure which employs a thin strained silicon layer at the top of the channel and the N-Drift region. The strain is induced by a relaxed Si0.8 Ge0.2 layer which is on top of a compositionally graded SiGe buffer. We explain the underlying physics of the device and compare the proposed device with a conventional LDMOS in terms of energy band diagram and carrier concentration. Numerical simulations of the proposed strained silicon laterally diffused MOS using a 2 dimensional device simulator indicate improvements in saturation and linear transconductance, current drivability, cut off frequency and on resistance. These improvements are however accompanied with a suppression in the break down voltage.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.