Abstract: The present paper is an experimental investigation of
roughness effects on nucleate pool boiling of refrigerant R113 on
horizontal circular copper surfaces. The copper samples were treated
by different sand paper grit sizes to achieve different surface
roughness. The average surface roughness of the four samples was
0.901, 0.735, 0.65, and 0.09, respectively. The experiments were
performed in the heat flux range of 8 to 200kW/m2. The heat transfer
coefficient was calculated by measuring wall superheat of the
samples and the input heat flux. The results show significant
improvement of heat transfer coefficient as the surface roughness is
increased. It is found that the heat transfer coefficient of the sample
with Ra=0.901 is 3.4, 10.5, and 38.5% higher in comparison with
surfaces with Ra of 0.735, 0.65, and 0.09 at heat flux of 170 kW/m2.
Moreover, the results are compared with literature data and the well
known Cooper correlation.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: Sensor Network are emerging as a new tool for
important application in diverse fields like military surveillance,
habitat monitoring, weather, home electrical appliances and others.
Technically, sensor network nodes are limited in respect to energy
supply, computational capacity and communication bandwidth. In
order to prolong the lifetime of the sensor nodes, designing efficient
routing protocol is very critical. In this paper, we illustrate the
existing routing protocol for wireless sensor network using data
centric approach and present performance analysis of these protocols.
The paper focuses in the performance analysis of specific protocol
namely Directed Diffusion and SPIN. This analysis reveals that the
energy usage is important features which need to be taken into
consideration while designing routing protocol for wireless sensor
network.
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: In this study rack systems that are structural storage
units of warehouses have been analyzed as structural with Finite
Element Method (FEA). Each cell of discussed rack system storages
pallets which have from 800 kg to 1000 kg weights and
0.80x1.15x1.50 m dimensions. Under this load, total deformations
and equivalent stresses of structural elements and principal stresses,
tensile stresses and shear stresses of connection elements have been
analyzed. The results of analyses have been evaluated according to
resistance limits of structural and connection elements. Obtained
results have been presented as visual and magnitude.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: In this paper the features of multiple material gate
silicon-on-insulator MOSFETs are presented and compared with
single material gate silicon-on-insulator MOSFET structures. The
results indicate that the multiple material gate structures reduce short
channel effects such as drain induce barrier lowering, hot electron
effect and better current characteristics in comparison with single
material structures
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: Relevant agricultural information disseminator
(extension agent) ratio of 1:3500 farm families which become a
menace to agricultural production capacity in developing countries
necessitate this study. Out of 4 zones in the state, 24 extension agents
in each zone, 4 extension agents using cell phones and 120 farmers
using cell phone and 120 other farmers not using cell phone were
purposively selected to give 240 farmers that participated in the
research. Data were collected using interview guide and analysized
using frequency, percentage and t-test.. Frequency of contact with
agricultural information centers revealed that cell phone user farmers
had greater means score of X 41.43 contact as against the low mean
X19.32 contact recorded by farmers receiving agricultural
information from extension agents not using cell phone and their
production was statistically significant at P < 0.05. Usage of cell
phone increase extension agent contact and increase farmers-
production capacity.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: The main objective of this paper is to estimate the cost of road traffic accidents in Egypt. The Human Capital (HC) approach, specifically the Gross-Loss-of-Output methodology, is adopted for estimation. Moreover, cost values obtained by previous national literature are updated using the inflation rates. The results indicate an estimated cost of road traffic accidents in Egypt of approximately 10 billion Egyptian Pounds (about $US 1.8 billion) for the year 2008. In addition, it is expected that this cost will rise in 2009 to 11.8 billion Egyptian Pounds (about $US 2.1 billion).
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: In this paper, propagation of cos-Gaussian beam in strongly nonlocal nonlinear media has been stimulated by using paraxial group transformation. At first, cos-Gaussian beam, nonlocal nonlinear media, critical power, transfer matrix, and paraxial group transformation are introduced. Then, the propagation of the cos-Gaussian beam in strongly nonlocal nonlinear media is simulated. Results show that beam propagation has periodic structure during self-focusing effect in this case. However, this simple method can be used for investigation of propagation of kinds of beams in ABCD optical media.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: The paper shows some ability to manage two-phase
flows arising from the use of unsteady effects. In one case, we
consider the condition of fragmentation of the interface between the
two components leads to the intensification of mixing. The problem
is solved when the temporal and linear scale are small for the
appearance of the developed mixing layer. Showing that exist such
conditions for unsteady flow velocity at the surface of the channel,
which will lead to the creation and fragmentation of vortices at Re
numbers of order unity. Also showing that the Re is not a criterion of
similarity for this type of flows, but we can introduce a criterion that
depends on both the Re, and the frequency splitting of the vortices. It
turned out that feature of this situation is that streamlines behave
stable, and if we analyze the behavior of the interface between the
components it satisfies all the properties of unstable flows. The other
problem we consider the behavior of solid impurities in the extensive
system of channels. Simulated unsteady periodic flow modeled
breaths. Consider the behavior of the particles along the trajectories.
It is shown that, depending on the mass and diameter of the particles,
they can be collected in a caustic on the channel walls, stop in a
certain place or fly back. Of interest is the distribution of particle
velocity in frequency. It turned out that by choosing a behavior of the
velocity field of the carrier gas can affect the trajectory of individual
particles including force them to fly back.
Abstract: This article first summarizes reasons why current approaches supporting Open Learning and Distance Education need to be complemented by tools permitting lecturers, researchers and students to cooperatively organize the semantic content of Learning related materials (courses, discussions, etc.) into a fine-grained shared semantic network. This first part of the article also quickly describes the approach adopted to permit such a collaborative work. Then, examples of such semantic networks are presented. Finally, an evaluation of the approach by students is provided and analyzed.
Abstract: Understanding how airborne pathogens are
transported through hospital wards is essential for determining the
infection risk to patients and healthcare workers. This study utilizes
Computational Fluid Dynamics (CFD) simulations to explore
possible pathogen transport within a six-bed partitioned Nightingalestyle
hospital ward.
Grid independence of a ward model was addressed using the Grid
Convergence Index (GCI) from solutions obtained using three fullystructured
grids. Pathogens were simulated using source terms in
conjunction with a scalar transport equation and a RANS turbulence
model. Errors were found to be less than 4% in the calculation of air
velocities but an average of 13% was seen in the scalar field.
A parametric study of variations in the pathogen release point
illustrated that its distribution is strongly influenced by the local
velocity field and the degree of air mixing present.