Abstract: Later marine propeller is the main component of ship
propulsion system. For a non-series propeller, it is difficult to
indicate the open water marine propeller performance without an
experimental study to measure the marine propeller parameters.
In the present study, the open water performance of a non-series
marine propeller has been carried out experimentally. The
geometrical aspects of a commercial non-series marine propeller
have been measured for a propeller blade area ratio of 0.3985. The
measured propeller performance parameters were the thrust and
torque coefficients for different propeller rotational speed and
different water channel flow velocity, then the open water
performance for the propeller has been plotted.
In addition, a direct comparison between the obtained
experimental results and a theoretical study of a B-series marine
propeller of the same blade area ratio has been carried out. A
correction factor has been introduced to apply the operating
conditions of the experimental results to that of the theoretical study
for the studied marine propeller.
Abstract: The problem of controlling a two link robotic manipulator, consisting of a rotating and a prismatic links, is addressed. The actuations of both links are assumed to have unknown dead zone nonlinearities and friction torques modeled by LuGre friction model. Because of the existence of the unknown dead zone and friction torque at the actuations, unknown parameters and unmeasured states would appear to be part of the overall system dynamics that need for estimation. Unmeasured states observer, unknown parameters estimators, and robust adaptive control laws have been derived such that closed loop global stability is achieved. Simulation results have been performed to show the efficacy of the suggested approach.
Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: MRAM technology provides a combination of fast
access time, non-volatility, data retention and endurance. While a
growing interest is given to two-terminal Magnetic Tunnel Junctions
(MTJ) based on Spin-Transfer Torque (STT) switching as the
potential candidate for a universal memory, its reliability is
dramatically decreased because of the common writing/reading path.
Three-terminal MTJ based on Spin-Orbit Torque (SOT) approach
revitalizes the hope of an ideal MRAM. It can overcome the
reliability barrier encountered in current two-terminal MTJs by
separating the reading and the writing path. In this paper, we study
two possible writing schemes for the SOT-MTJ device based on
recently fabricated samples. While the first is based on precessional
switching, the second requires the presence of permanent magnetic
field. Based on an accurate Verilog-A model, we simulate the two
writing techniques and we highlight advantages and drawbacks of
each one. Using the second technique, pioneering logic circuits based
on the three-terminal architecture of the SOT-MTJ described in this
work are under development with preliminary attractive results.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: This paper presents a speed fuzzy sliding mode
controller for a vector controlled induction machine (IM) fed by a
voltage source inverter (PWM).
The sliding mode based fuzzy control method is developed to
achieve fast response, a best disturbance rejection and to maintain a
good decoupling.
The problem with sliding mode control is that there is high
frequency switching around the sliding mode surface. The FSMC is
the combination of the robustness of Sliding Mode Control (SMC)
and the smoothness of Fuzzy Logic (FL). To reduce the torque
fluctuations (chattering), the sign function used in the conventional
SMC is substituted with a fuzzy logic algorithm.
The proposed algorithm was simulated by Matlab/Simulink
software and simulation results show that the performance of the
control scheme is robust and the chattering problem is solved.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: This paper will provide the kinematic and dynamic
analysis of a lower limb exoskeleton. The forward and inverse
kinematics of proposed exoskeleton is performed using Denevit and
Hartenberg method. The torques required for the actuators will be
calculated using Lagrangian formulation technique. This research can
be used to design the control of the proposed exoskeleton.
Abstract: In this paper by using the port-controlled Hamiltonian
(PCH) systems theory, a full-order nonlinear controlled model is first
developed. Then a nonlinear passivity-based robust adaptive control
(PBRAC) of switched reluctance motor in the presence of external
disturbances for the purpose of torque ripple reduction and
characteristic improvement is presented. The proposed controller
design is separated into the inner loop and the outer loop controller.
In the inner loop, passivity-based control is employed by using
energy shaping techniques to produce the proper switching function.
The outer loop control is employed by robust adaptive controller to
determine the appropriate Torque command. It can also overcome the
inherent nonlinear characteristics of the system and make the whole
system robust to uncertainties and bounded disturbances. A 4KW 8/6
SRM with experimental characteristics that takes magnetic saturation
into account is modeled, simulation results show that the proposed
scheme has good performance and practical application prospects.
Abstract: Cutting tools are widely used in manufacturing processes and drilling is the most commonly used machining process. Although drill-bits used in drilling may not be expensive, their breakage can cause damage to expensive work piece being drilled and at the same time has major impact on productivity. Predicting drill-bit breakage, therefore, is important in reducing cost and improving productivity. This study uses twenty features extracted from two degradation signals viz., thrust force and torque. The methodology used involves developing and comparing decision tree, random forest, and multinomial logistic regression models for classifying and predicting drill-bit breakage using degradation signals.
Abstract: Fuzzy controllers are potential candidates for the
control of nonlinear, time variant and also complicated systems. Anti
lock brake system (ABS) which is a nonlinear system, may not be
easily controlled by classical control methods. An intelligent Fuzzy
control method is very useful for this kind of nonlinear system. A
typical antilock brake system (ABS) by sensing the wheel lockup,
releases the brakes for a short period of time, and then reapplies again
the brakes when the wheel spins up. In this paper, an intelligent fuzzy
ABS controller is designed to adjust slipping performance for variety
of roads. There are tow major sections in the proposing control
system. First section consists of tow Fuzzy-Logic Controllers (FLC)
providing optimal brake torque for both front and rear wheels.
Second section which is also a FLC provides required amount of slip
and torque references properties for different kind of roads.
Simulation results of our proposed intelligent ABS for three different
kinds of road show more reliable and better performance in compare
with two other break systems.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: This paper presents a numerical analysis of the
performance of a three-bladed Darrieus vertical-axis wind turbine
based on the DU91-W2-250 airfoil. A complete campaign of 2-D
simulations, performed for several values of tip speed ratio and based
on RANS unsteady calculations, has been performed to obtain the
rotor torque and power curves. Rotor performances have been
compared with the results of a previous work based on the use of the
NACA 0021 airfoil. Both the power coefficient and the torque
coefficient have been determined as a function of the tip speed ratio.
The flow field around rotor blades has also been analyzed. As a final
result, the performance of the DU airfoil based rotor appears to be
lower than the one based on the NACA 0021 blade section. This
behavior could be due to the higher stall characteristics of the NACA
profile, being the separation zone at the trailing edge more extended
for the DU airfoil.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.