Abstract: Currently, there has been a 3G mobile networks data
traffic explosion due to the large increase in the number of smartphone
users. Unlike a traditional wired infrastructure, 3G mobile networks
have limited wireless resources and signaling procedures for complex
wireless resource management. And mobile network security for
various abnormal and malicious traffic technologies was not ready. So
Malicious or potentially malicious traffic originating from mobile
malware infected smart devices can cause serious problems to the 3G
mobile networks, such as DoS and scanning attack in wired networks.
This paper describes the DoS security threat in the 3G mobile network
and proposes a detection technology.
Abstract: I/O workload is a critical and important factor to
analyze I/O pattern and to maximize file system performance.
However to measure I/O workload on running distributed parallel file
system is non-trivial due to collection overhead and large volume of
data. In this paper, we measured and analyzed file system activities on
two large-scale cluster systems which had TFlops level high
performance computation resources. By comparing file system
activities of 2009 with those of 2006, we analyzed the change of I/O
workloads by the development of system performance and high-speed
network technology.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: This study aims to analyze the effect of e-learning on
photonics technology and daily livings among college students. The
course contents of photonics technology and daily livings are first
drafted based on research discussions and expert interviews. Having
expert questionnaires with Delphi Technique for three times, the
knowledge units and items for the course of photonics technology and
daily livings are established. The e-learning materials and the drafts of
instructional strategies, academic achievement, and learning attitude
scales are then developed. With expert inspection, reliability and
validity test, and experimental instructions, the scales and the material
are further revised. Finally, the formal instructions are implemented to
test the effect of different instructional methods on the academic
achievement of photonics technology and daily livings among students
in universities of technology. The research results show that e-learning
could effectively promote academic achievement and learning
attitude, and the students with e-learning obviously outperform the
ones with trandition instructions.
Abstract: The Ministry of Defense (MoD) spends hundreds of
millions of dollars on software to support its infrastructure, operate
its weapons and provide command, control, communications,
computing, intelligence, surveillance, and reconnaissance (C4ISR)
functions. These and other all new advanced systems have a common
critical component is information technology. Defense and
Aerospace environment is continuously striving to keep up with
increasingly sophisticated Information Technology (IT) in order to
remain effective in today-s dynamic and unpredictable threat
environment. This makes it one of the largest and fastest growing
expenses of Defense. Hundreds of millions of dollars spent a year on
IT projects. But, too many of those millions are wasted on costly
mistakes. Systems that do not work properly, new components that
are not compatible with old once, trendily new applications that do
not really satisfy defense needs or lost though poorly managed
contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology Acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of sous vide packaging during
the storage time of salad with meat in mayonnaise at different storage
temperature. Samples were evaluated at 0, 1, 3, 7, 10, 15, 18, 25, 29,
42, and 52 storage days at the storage temperature of +4±0.5 ºC and
+10±0.5 ºC. Experimentally the quality of the salad with meat in
mayonnaise was characterized by measuring colour, pH and
microbiological properties. The sous vide packaging was effective in
protecting the product from physical, chemical, and microbial quality
degradation. The sous vide packaging significantly reduces microbial
growth at storage temperature of +4±0.5 ºC and +10±0.5 ºC.
Moreover, it is possible to extend the product shelf life to 52 days
even when stored at +10±0.5 ºC.
Abstract: Educational institutions are increasingly exploring the affordances of 3D virtual worlds for instruction and research, but few studies have been done to document current practices and uses of this emerging technology. This observational survey examines the virtual presences of 170 accredited educational institutions found in one such 3D virtual world called Second Life®, created by San- Francisco based Linden Lab®. The study focuses on what educational institutions look like in this virtual environment, the types of spaces educational institutions are creating or simulating, and what types of activities are being conducted.
Abstract: Due to dynamic evolution, the ability of a
manufacturing technology to produce a special product is changing.
Therefore, it is essential to monitor the established techniques and
processes to detect whether a company-s production will fit future
circumstances. Concerning the manufacturing technology planning
process, companies must decide when to change to a new technology
for maintaining and increasing competitive advantages. In this
context, the maturity assessment of the focused technologies is
crucial. This article presents an approach for defining the maturity of
a manufacturing technology from a strategic point of view. The
concept is based on the approach of technology readiness level
(TRL) according to NASA (National Aeronautics and Space
Administration), but also includes dynamic changes. Therefore, the
model takes into account the concept of the technology life cycle.
Furthermore, it enables a company to estimate the ideal date for
implementation of a new manufacturing technology.
Abstract: An on chip low drop out voltage regulator that
employs elegant compensation scheme is presented in this paper. The
novelty in this design is that the device parasitic capacitances are
exploited for compensation at different loads. The proposed LDO is
designed to provide a constant voltage of 1.2V and is implemented in
UMC 180 nano meter CMOS technology. The voltage regulator
presented improves stability even at lighter loads and enhances line
and load regulation.
Abstract: With the proliferation of the mobile device
technologies, mobile learning can be used to complement and
improve traditional learning problems. Both students and teachers
need a proper and handy system to monitor and keep track the
performance of the students. This paper presents an implementation
of M-learning for primary school in Malaysia by using an open
source technology. It focuses on learning mathematics using
handheld devices for primary schools- students aged 11 and 12 years
old. Main users for this system include students, teachers and the
administrator. This application suggests a new mobile learning
environment with mobile graph for tracking the students- progress
and performance. The purpose of this system is not to replace
traditional classroom but to complement the learning process. In a
testing conducted, students who used this system performed better in
their examination.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: In this paper, an efficient wave concept iterative
process (WCIP) with auxiliary Sources is presented for full wave
investigation of an active microwave structure on micro strip
technology. Good agreement between the experimental and
simulation results is observed.
Abstract: This paper discusses ways to foster cooperative learning through the integration of online communication technology. While the education experts believe constructivism produces a more positive learning experience, the educators are still facing problems in getting students to participate due to numerous reasons such as shy personality, language and cultural barriers. This paper will look into the factors that lead to lack of participations among students and how technology can be implemented to overcome these issues.
Abstract: A new interface circuit for capacitive sensor is
presented. This paper presents the design and simulation of soil
moisture capacitive sensor interface circuit based on phase
differential technique. The circuit has been designed and fabricated
using MIMOS- 0.35"m CMOS technology. Simulation and test
results show linear characteristic from 36 – 52 degree phase
difference, representing 0 – 100% in soil moisture level. Test result
shows the circuit has sensitivity of 0.79mV/0.10 phase difference,
translating into resolution of 10% soil moisture level.
Abstract: Presently and in line with the United Nations (EPA),
human thinking system has shifted towards clean fuels so as to
maintain a cleaner environment and to save our planet earth.
One of the most successful studies in order to achieve new
energies includes the use of animal wastes and their organic residues,
and the result of these researches has been represented in the form of
very simple and cheap methods called biogas technology. Biogas
technology has developed a lot in the recent decades; its reason is the
high cost of fossil fuels and the greater attention of countries to the
environmental pollutions due to the consumption of this kind of
fuels.
IRAN is ready for the optimized application of renewable
energies, having much enriched resources of this kind of energies; so
a special place could be considered for it when making programs.
The purpose of biogas technology is the recovery of energy and
finally the protection of the environment, which is much appropriate
for the third world farmers with respect to their technical abilities and
economic potentials. Studies show that the production and
consumption of biogas is appropriate and economic in IRAN,
because of the high amount of waste in the agriculture sector, the
significant amount of animal and human excrement production, the
great volume of garbage produced and the most important the
specific social, climatic and agricultural conditions in IRAN, in order
to proceed towards the reduction of pollution due to the use of fossil
fuels.
Abstract: This paper presents a review on vision aided systems
and proposes an approach for visual rehabilitation using stereo vision
technology. The proposed system utilizes stereo vision, image
processing methodology and a sonification procedure to support
blind navigation. The developed system includes a wearable
computer, stereo cameras as vision sensor and stereo earphones, all
moulded in a helmet. The image of the scene infront of visually
handicapped is captured by the vision sensors. The captured images
are processed to enhance the important features in the scene in front,
for navigation assistance. The image processing is designed as model
of human vision by identifying the obstacles and their depth
information. The processed image is mapped on to musical stereo
sound for the blind-s understanding of the scene infront. The
developed method has been tested in the indoor and outdoor
environments and the proposed image processing methodology is
found to be effective for object identification.
Abstract: A new OTA-based logarithmic-control variable gain
current amplifier (LCCA) is presented. It consists of two Operational
Transconductance Amplifier (OTA) and two PMOS transistors
biased in weak inversion region. The circuit operates from 0.6V DC
power supply and consumes 0.6 μW. The linear-dB controllable
output range is 43 dB with maximum error less than 0.5dB. The
functionality of the proposed design was confirmed using HSPICE in
0.35μm CMOS process technology.
Abstract: Scalability poses a severe threat to the existing
DRAM technology. The capacitors that are used for storing and
sensing charge in DRAM are generally not scaled beyond 42nm.
This is because; the capacitors must be sufficiently large for reliable
sensing and charge storage mechanism. This leaves DRAM memory
scaling in jeopardy, as charge sensing and storage mechanisms
become extremely difficult. In this paper we provide an overview of
the potential and the possibilities of using Phase Change Memory
(PCM) as an alternative for the existing DRAM technology. The
main challenges that we encounter in using PCM are, the limited
endurance, high access latencies, and higher dynamic energy
consumption than that of the conventional DRAM. We then provide
an overview of various methods, which can be employed to
overcome these drawbacks. Hybrid memories involving both PCM
and DRAM can be used, to achieve good tradeoffs in access latency
and storage density. We conclude by presenting, the results of these
methods that makes PCM a potential replacement for the current
DRAM technology.