Abstract: The capability of CNC gantry milling machines in
manufacturing long components has caused the expanded use of such
machines. On the other hand, the machines’ gantry rigidity can
reduce under severe loads or vibration during operation. Indeed, the
quality of machining is dependent on the machine’s dynamic
behavior throughout the operating process. For this reason, these
types of machines have always been used widely and are not
efficient. Therefore, they can usually be employed for rough
machining and may not produce adequate surface finishing. In this
paper, a CNC gantry milling machine with the potential to produce
good surface finish has been designed and analyzed. The lowest
natural frequency of this machine is 202 Hz corresponding to 12000
rpm at all motion amplitudes with a full range of suitable frequency
responses. Meanwhile, the maximum deformation under dead loads
for the gantry machine is 0.565*m, indicating that this machine tool
is capable of producing higher product quality.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: Effect of biopesticide from wood vinegar and
extracted substances from 3 medicinal plants such as: non taai yak
(Stemona tuberosa Lour), boraphet (Tinospora crispa Mier) and
derris (Derris elliptica Roxb) were tested on the age five years of
pomelo. The selected pomelo was carried out for insects’ pest control
and its quality. The experimental site was located at farmer’s orchard
in Phichit Province, Thailand. This study was undertaken during the
drought season (December to March). The extracted from plants and
wood vinegar were evaluated in 6 treatments: 1) water as control; 2)
wood vinegar; 3) S. tuberosa Lour; 4) T. crispa Mier; 5) D. elliptica
Roxb; 6) mixed (wood vinegar + S. tuberosa Lour + T. crispa Mier +
D. elliptica Roxb). The experiment was RCB with 6 treatments and 3
replications per treatment. The results showed that T. crispa Mier was
the highest effectiveness for reduction population of thrips
(Scirtothrips dorsalis Hood) and citrus leaf miner (Phyllocnistis
citrella Stainton) at 14.10 and 15.37 respectively, followed by
treatment of mixed, D. elliptica Roxb, S. tuberosa Lour and wood
vinegar with significance different. Additionally, T. crispa Mier
promoted the high quality of harvested pomelo in term of thickness
of skin at 12.45 mm and S. tuberosa Lour gave the high quality of the
pomelo in term of firmness (276.5 kg/cm2) and brix (11.0%).
Abstract: An experiment was conducted to determine the effect
of pollination on seed quality of rapeseed in Chitwan, Nepal during
2012-2013. The experiment was designed in Randomized Complete
Block with four replications and five treatments. The rapeseed plots
were caged with mosquito nets at 10% flowering except natural
pollination. Two-framed colonies of Apis mellifera L. and Apis
cerana F. were introduced separately for pollination, and control plot
caged without pollinators. The highest germination percent was
observed on Apis cerana F. pollinated plot seeds (90.50%
germination) followed by Apis mellifera L. pollinated plots (87.25 %)
and lowest on control plots (42.00% germination) seeds. Similarly,
seed test weight of Apis cerana F. pollinated plots (3.22 gm/ 1000
seed) and Apis mellifera L. pollinated plots (2.93 gm/1000 seed) were
and lowest on control plots (2.26 gm/ 1000 seed) recorded. Likewise,
oil content was recorded highest on pollinated by Apis cerana F.
(36.1%) followed by pollinated by Apis mellifera L. (35.4%) and
lowest on control plots (32.8%). This study clearly indicated
pollination increases the seed quality of rapeseed and therefore,
management of honeybee is necessary for producing higher quality of
rapeseed under Chitwan condition.
Abstract: The concept of urban transformation came about
through interventions aimed at bringing socially and economically
problematic areas of cities into use. The issue of urban transformation
arose frequently during the post-2000 period in particular, and legal
regulations on this matter were also developed in Turkey. Urban
transformation project would be a focal point for the formation of the
city in the near future. Izmir, which is third largest city of Turkey, is
an important trade and port city. But, assessment of the current
situation shows that, the majority of existing residential areas was
formed with squatters and unplanned settlements in Izmir city center.
Therefore an important part of these areas have significant problems
in terms of the quality of life, safety and environmental quality. In
this study, the central policies in Turkey and local policies in Đzmir
about urban transformation will be considered. In addition, urban
renewal projects that are being implemented in Izmir were discussed
and suggestions will be developed in accordance with this policy.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: This study examines several critical dimensions of eservice
quality overlooked in the existing literature and proposes a
model and instrument framework for measuring customer perceived
e-service quality in the banking sector. The initial design was derived
from a pool of instrument dimensions and their items from the
existing literature review by content analysis. Based on focused
group discussion, nine dimensions were extracted. An exploratory
factor analysis approach was applied to data from a survey of 323
respondents. The instrument has been designed specifically for the
banking sector. Research data was collected from bank customers
who use electronic banking in a developing economy. A nine-factor
instrument has been proposed to measure the e-service quality. The
instrument has been checked for reliability. The validity and sample
place limited the applicability of the instrument across economies and
service categories. Future research must be conducted to check the
validity. This instrument can help bankers in developing economies
like India to measure the e-service quality and make improvements.
The present study offers a systematic procedure that provides insights
on to the conceptual and empirical comprehension of customer
perceived e-service quality and its constituents.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: E-service quality plays a significant role to achieve
success or failure in any organization, offering services online. It will
increase the competition among the organizations, to attract the
customers on the basis of the quality of service provided by the
organization. Better e-service quality will enhance the relationship
with customers and their satisfaction. So the measurement of eservice
quality is very important but it is a complex process due to
the complex nature of services. Literature predicts that there is a lack
of universal definition of e-service quality. The e-service quality
measures in banking have great importance in achieving high
customer base. This paper proposes a conceptual model for
measuring e-service quality in Indian Banking Industry. Nine
dimensions reliability, ease of use, personalization, security and trust,
website aesthetic, responsiveness, contact and fulfillment had been
identified. The results of this paper may help to develop a proper
scale to measure the e-service quality in Indian Banking Industry,
which may assist to maintain and improve the performance and
effectiveness of e-service quality to retain customers.
Abstract: Medical imaging produces human body pictures in
digital form. Since these imaging techniques produce prohibitive
amounts of data, compression is necessary for storage and
communication purposes. Many current compression schemes
provide a very high compression rate but with considerable loss of
quality. On the other hand, in some areas in medicine, it may be
sufficient to maintain high image quality only in region of interest
(ROI). This paper discusses a contribution to the lossless
compression in the region of interest of Scintigraphic images based
on SPIHT algorithm and global transform thresholding using
Huffman coding.
Abstract: Many quality models have been used to measure egovernment
portals quality. However, the absence of an international
consensus for e-government portals quality models results in many
differences in terms of quality attributes and measures. The aim of
this paper is to compare and analyze the existing e-government
quality models proposed in literature (those that are based on ISO
standards and those that are not) in order to propose guidelines to
build a good and useful e-government portals quality model. Our
findings show that, there is no e-government portal quality model
based on the new international standard ISO 25010. Besides that, the
quality models are not based on a best practice model to allow
agencies to both; measure e-government portals quality and identify
missing best practices for those portals.
Abstract: The current study explored the effect of economic
development, financial development and institutional quality on
environmental destruction in upper-middle income countries during
the time period of 1999-2011. The dependent variable is logarithm of
carbon dioxide emissions that can be considered as an index for
destruction or quality of the environment given to its effects on the
environment. Financial development and institutional development
variables as well as some control variables were considered. In order
to study cross-sectional correlation among the countries under study,
Pesaran and Friz test was used. Since the results of both tests show
cross-sectional correlation in the countries under study, seemingly
unrelated regression method was utilized for model estimation. The
results disclosed that Kuznets’ environmental curve hypothesis is
confirmed in upper-middle income countries and also, financial
development and institutional quality have a significant effect on
environmental quality. The results of this study can be considered by
policy makers in countries with different income groups to have
access to a growth accompanied by improved environmental quality.
Abstract: The cooling channels of injection mould play a crucial
role in determining the productivity of moulding process and the
product quality. It’s not a simple task to design high quality cooling
channels. In this paper, an intelligent cooling channels design system
including automatic layout of cooling channels, interference checking
and assembly of accessories is studied. Automatic layout of cooling
channels using genetic algorithm is analyzed. Through integrating
experience criteria of designing cooling channels, considering the
factors such as the mould temperature and interference checking, the
automatic layout of cooling channels is implemented. The method of
checking interference based on distance constraint algorithm and the
function of automatic and continuous assembly of accessories are
developed and integrated into the system. Case studies demonstrate the
feasibility and practicality of the intelligent design system.
Abstract: This paper presents a real-time visualization technique
and filtering of classified LiDAR point clouds. The visualization is
capable of displaying filtered information organized in layers by the
classification attribute saved within LiDAR datasets. We explain the
used data structure and data management, which enables real-time
presentation of layered LiDAR data. Real-time visualization is
achieved with LOD optimization based on the distance from the
observer without loss of quality. The filtering process is done in two
steps and is entirely executed on the GPU and implemented using
programmable shaders.
Abstract: The study was conducted to evaluate the efficiency of
Garlic and Chili combination solution on control of insect pests in
cabbage crop. The solution was sprayed at different intervals after
transplanting. The efficiency of Garlic and chili combination solution
on cabbage insect pests was measured. Results revealed that Garlic
and chili combination solution was the effectively reduced cabbage
insect pests. On other hand, the spray solution not only reduced the
number of days required for the cabbage growth but also greatly
enhanced the leaf number, head diameter, head weight, and quality of
cabbage. Garlic and chili combination solution have positive effects
on pests reduction and improve growth, yield and quality of cabbage
vegetable.
Abstract: Researches and concerns in power quality gained
significant momentum in the field of power electronics systems over
the last two decades globally. This sudden increase in the number of
concerns over power quality problems is a result of the huge increase
in the use of non-linear loads. In this paper, power quality evaluation
of some distribution networks at Misurata - Libya has been done
using a power quality and energy analyzer (Fluke 437 Series II). The
results of this evaluation are used to minimize the problems of power
quality. The analysis shows the main power quality problems that
exist and the level of awareness of power quality issues with the aim
of generating a start point which can be used as guidelines for
researchers and end users in the field of power systems.
Abstract: In the last few years, harmonics have been occurred
with the increasing use of nonlinear loads, and these harmonics have
been an ever increasing problem for the line systems. This situation
importantly affects the quality of power and gives large losses to the
network. An efficient way to solve these problems is providing
harmonic compensation through parallel active power filters. Many
methods can be used in the control systems of the parallel active
power filters which provide the compensation. These methods
efficiently affect the performance of the active power filters. For this
reason, the chosen control method is significant. In this study, Fourier
analysis (FA) control method and synchronous reference frame (SRF)
control method are discussed. These control methods are designed for
both eliminate harmonics and perform reactive power compensation
in MATLAB/Simulink pack program and are tested. The results have
been compared for each two methods.
Abstract: This paper deals with the assessment of faulted area around an industrial customer connected to a particular electric grid that will cause a certain sag magnitude on this customer. The faulted (critical or exposed) area’s length is calculated by adding all line lengths in the neighborhood of the critical node (customer). The applied method is the so-called Method of Critical Distances. By using advanced short-circuit analysis, the Critical Area can be accurately calculated for radial and meshed power networks due to all symmetrical and asymmetrical faults. For the demonstration of the effectiveness of the proposed methodology, a study case is used.