Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: Instead of representing individual cognition only, population cognition is represented using artificial neural networks whilst maintaining individuality. This population network trains continuously, simulating adaptation. An implementation of two coexisting populations is compared to the Lotka-Volterra model of predator-prey interaction. Applications include multi-agent systems such as artificial life or computer games.
Abstract: European Rail Traffic Management System (ERTMS) is the European reference for interoperable and safer signaling systems to efficiently manage trains running. If implemented, it allows trains cross seamlessly intra-European national borders. ERTMS has defined a secure communication protocol, EURORADIO, based on open communication networks. Its RadioInfill function can improve the reaction of the signaling system to changes in line conditions, avoiding unnecessary braking: its advantages in terms of power saving and travel time has been analyzed. In this paper a software implementation of the EURORADIO protocol with RadioInfill for ERTMS Level 1 using GSM-R is illustrated as part of the SR-Secure Italian project. In this building-blocks architecture the EURORADIO layers communicates together through modular Application Programm Interfaces. Security coding rules and railway industry requirements specified by EN 50128 standard have been respected. The proposed implementation has successfully passed conformity tests and has been tested on a computer-based simulator.
Abstract: The standard approach to image reconstruction is to stabilize the problem by including an edge-preserving roughness penalty in addition to faithfulness to the data. However, this methodology produces noisy object boundaries and creates a staircase effect. The existing attempts to favor the formation of smooth contour lines take the edge field explicitly into account; they either are computationally expensive or produce disappointing results. In this paper, we propose to incorporate the smoothness of the edge field in an implicit way by means of an additional penalty term defined in the wavelet domain. We also derive an efficient half-quadratic algorithm to solve the resulting optimization problem, including the case when the data fidelity term is non-quadratic and the cost function is nonconvex. Numerical experiments show that our technique preserves edge sharpness while smoothing contour lines; it produces visually pleasing reconstructions which are quantitatively better than those obtained without wavelet-domain constraints.
Abstract: This paper presents a simple and original method for
the generation of short monocycle pulses based on the transient
response of a passive band-pass filter. The recorded sub-nanosecond
pulses show a good symmetry and a small ringing (13 % of the peak
amplitude). Their spectral density covers the range 3.1 GHz to
10.6 GHz. The possibility to adapt the pulse spectral density to the
indoor FCC frequency mask is demonstrated with a prototype
working at a reduced frequency (FCC/1000). A detection technique is
proposed.
Abstract: Multicast transmissions allow an host (the source) to send only one flow bound for a group of hosts (the receivers). Any equipment eager to belong to the group may explicitly register itself to that group via its multicast router. This router will be given the responsibility to convey all information relating to the group to all registered hosts. However in an environment in which the final receiver or the source frequently moves, the multicast flows need particular treatment. This constitutes one of the multicast transmissions problems around which several proposals were made in the Mobile IPv6 case in general. In this article, we describe the problems involved in this IPv6 multicast mobility and the existing proposals for their resolution. Then architecture will be proposed aiming to satisfy and optimize these transmissions in the specific case of a mobile multicast receiver in NC-HMIPv6 environment.
Abstract: Providing Services at Home has become over the last
few years a very dynamic and promising technological domain. It is
likely to enable wide dissemination of secure and automated living
environments. We propose a methodology for identifying threats to
Services at Home Delivery systems, as well as a threat analysis
of a multi-provider Home Gateway architecture. This methodology
is based on a dichotomous positive/preventive study of the target
system: it aims at identifying both what the system must do, and
what it must not do. This approach completes existing methods with
a synthetic view of potential security flaws, thus enabling suitable
measures to be taken into account. Security implications of the
evolution of a given system become easier to deal with. A prototype
is built based on the conclusions of this analysis.
Abstract: The past decade has witnessed a good opportunities
for city development schemes in UK. The government encouraged
restoration of city centers to comprise mixed use developments with
high density residential apartments. Investments in regeneration areas
were doing well according to the analyses of Property Databank
(IPD). However, more recent analysis by IPD has shown that since
2007, property in regeneration areas has been more vulnerable to the
market downturn than other types of investment property. The early
stages of a property market downturn may be felt most in
regeneration where funding, investor confidence and occupier
demand would dissipate because the sector was considered more
marginal or risky when development costs rise. Moreover, the Bank
of England survey shows that lenders have sequentially tightened the
availability of credit for commercial real estate since mid-2007. A
sharp reduction in the willingness of banks to lend on commercial
property was recorded. The credit crunch has already affected
commercial property but its impact has been particularly severe in
certain kinds of properties where residential developments are
extremely difficult, in particular city centre apartments and buy-to-let
markets. Commercial property – retail, industrial leisure and mixed
use were also pressed, in Birmingham; tens of mixed use plots were
built to replace old factories in the heart of the city. The purpose of
these developments was to enable young professionals to work and
live in same place. Thousands of people lost their jobs during the
recession, moreover lending was more difficult and the future of
many developments is unknown. The recession casts its shadow upon
the society due to cuts in public spending by government, Inflation,
rising tuition fees and high rise in unemployment generated anger and
hatred was spreading among youth causing vandalism and riots in
many cities. Recent riots targeted many mixed used development in
the UK where banks, shops, restaurants and big stores were robbed
and set into fire leaving residents with horror and shock. This paper
examines the impact of the recession and riots on mixed use
development in UK.
Abstract: Although many studies on the assembly technology of
the bridge construction have dealt mostly with on the pier, girder or the
deck of the bridge, studies on the prefabricated barrier have rarely been
performed. For understanding structural characteristics and
application of the concrete barrier in the modular bridge, which is an
assembly of structure members, static loading test was performed.
Structural performances as a road barrier of the three methods,
conventional cast-in-place(ST), vertical bolt connection(BVC) and
horizontal bolt connection(BHC) were evaluated and compared
through the analyses of load-displacement curves, strain curves of the
steel, concrete strain curves and the visual appearances of crack
patterns. The vertical bolt connection(BVC) method demonstrated
comparable performance as an alternative to conventional
cast-in-place(ST) while providing all the advantages of prefabricated
technology. Necessities for the future improvement in nuts
enforcement as well as legal standard and regulation are also
addressed.
Abstract: The Integrated Performance Modelling Environment
(IPME) is a powerful simulation engine for task simulation and
performance analysis. However, it has no high level cognition such
as memory and reasoning for complex simulation. This article
introduces a knowledge representation and reasoning scheme that can
accommodate uncertainty in simulations of military personnel with
IPME. This approach demonstrates how advanced reasoning models
that support similarity-based associative process, rule-based abstract
process, multiple reasoning methods and real-time interaction can be
integrated with conventional task network modelling to provide
greater functionality and flexibility when modelling operator
performance.