Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Batch fermentation of 5, 10 and 25 g/L biodiesel
derived crude glycerol was carried out at 30, 37 and 450C by
Clostridium pasteurianum cells immobilized on silica. Maximum
yield of 1,3-propanediol (PDO) (0.60 mol/mol), and ethanol (0.26
mol/mol) were obtained from 10 g/L crude glycerol at 30 and 370C
respectively. Maximum yield of butanol (0.28 mol/mol substrate
added) was obtained at 370C with 25 g/L substrate. None of the three
products were detected at 45oC even after 10 days of fermentation.
Only traces of ethanol (0.01 mol/mol) were detected at 450C with 5
g/L substrate. The results obtained for 25 g/L substrate utilization
were fitted in first order rate equation to obtain the values of rate
constant at three different temperatures for bioconversion of glycerol.
First order rate constants for bioconversion of glycerol at 30, 37 and
45oC were found to be 0.198, 0.294 and 0.029/day respectively.
Activation energy (Ea) for crude glycerol bioconversion was
calculated to be 57.62 kcal/mol.
Abstract: This paper deals with rheological behavior of tomato
paste from the view point of time independent properties inclusive of
processing variables such as sample temperature which influence on
rheological properties as well as breaking temperature and
concentration which beside the rheological properties, influence on
the quality of final product. With this aim 10 tomato paste samples at
various concentrations (17-25%) and breaking temperatures (65-
85 C o ) have been produced. The experimental results showed tomato
paste behaves as a non-Newtonian semi-fluid which follows power
law model that consistency coefficient (K) is supposed function of
breaking temperature, concentration and sample temperature with
consideration to superimpose function.
Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: The present paper reports results of an experimental
program conducted to study performance of fly ash based
geopolymer pastes at elevated temperature. Three series of
geopolymer pastes differing in Na2O content (8.5%, 10% and 11.5%)
were manufactured by activating low calcium fly ash with a mixture
of sodium hydroxide and sodium silicate solution. The paste
specimens were subjected to temperatures as high as 900oC and the
behaviour at elevated temperatures were investigated on the basis of
physical appearance, weight losses, residual strength, shrinkage
measurements and sorptivity tests at different temperatures. Scanning
electron microscopy along with EDX and XRD tests were also
conducted to examine microstructure and mineralogical changes
during the thermal exposure. Specimens which were initially grey
turned reddish accompanied by appearance of small cracks as the
temperature increased to 900oC. Loss of weight was more in
specimens manufactured with highest Na2O content. Geopolymer
paste specimen containing minimum Na2O performed better than
those with higher Na2O content in terms of residual compressive
strength.
Abstract: One of the main concerns in the Information Technology field is adoption with new technologies in organizations which may result in increasing the usage paste of these technologies.This study aims to look at the issue of culture-s role in accepting and using new technologies in organizations. The study examines the effect of culture on accepting and intention to use new technology in organizations. Studies show culture is one of the most important barriers in adoption new technologies. The model used for accepting and using new technology is Technology Acceptance Model (TAM), while for culture and dimensions a well-known theory by Hofsted was used. Results of the study show significant effect of culture on intention to use new technologies. All four dimensions of culture were tested to find the strength of relationship with behavioral intention to use new technologies. Findings indicate the important role of culture in the level of intention to use new technologies and different role of each dimension to improve adaptation process. The study suggests that transferring of new technologies efforts are most likely to be successful if the parties are culturally aligned.
Abstract: This paper proposes a location-aware system for
household robots which allows users to paste predefined paper tags at
different locations according to users- comprehension of the house. In this system a household robot may be aware of its location and the
attributes thereof by visually recognizing the tags when the robot is moving. This paper also presents a novel user interface to define a
moving path of the robot, which allows users to draw the path in the air
with a finger so as to generate commands for following motions.
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.