Abstract: In this paper, a planar monopole antenna for multi band applications is proposed. The antenna structure operates at three operating frequencies at 3.7, 6.2, and 13.5 GHz which cover different communication frequency ranges. The antenna consists of a quasi-modified rectangular radiating patch with a partial ground plane and two parasitic elements (open-loop-ring resonators) to serve as coupling-bridges. A stepped cut at lower corners of the radiating patch and the partial ground plane are used, to achieve the multiband features. The proposed antenna is manufactured on the FR4 substrate and is simulated and optimized using High Frequency Simulation System (HFSS). The antenna topology possesses an area of 30.5 x 30 x 1.6 mm3. The measured results demonstrate that the candidate antenna has impedance bandwidths for 10 dB return loss and operates from 3.80 – 3.90 GHz, 4.10 – 5.20 GHz, 11.2 – 11.5 GHz and from 12.5 – 14.0 GHz, which meet the requirements of the wireless local area network (WLAN), worldwide interoperability for microwave access (WiMAX), C- (Uplink) and Ku- (Uplink) band applications. Acceptable agreement is obtained between measurement and simulation results. Experimental results show that the antenna is successfully simulated and measured, and the tri-band antenna can be achieved by adjusting the lengths of the three elements and it gives good gains across all the operation bands.
Abstract: Methodology is suggested to design a linear rectangular microstrip array antenna based on Yagi antenna theory. The antenna with different directors' lengths as parasitic elements were designed, simulated, and analyzed using HFSS. The calculus and results illustrate the effectiveness of using specific parasitic elements to improve the directivity and gain for microstrip array antenna. The results have shown that the suggested methodology has the potential to be applied for improving the antenna performance. Maximum radiation intensity (Umax) of the order of 0.47w/st was recorded, directivity of 6.58dB, and gain better than 6.07dB are readily achievable for the antenna that working.
Abstract: In this communication, a low-cost circularly
polarized wire antenna exhibiting improved gain performance for
Dedicated Short Range Communications (DSRC), vehicle-to-vehicle
(V2V) and vehicle-to-infrastructure (V2I) communications is
presented. The proposed antenna comprises a Y-shaped quarterwavelength
monopole antenna surrounded by two iterations of eight
conductive arched walls acting as parasitic elements to enhance the
overall antenna gain and to shape the radiation pattern in the H-plane.
A hemispherical radome shell is added to protect the antenna
structure and its effect on the antenna performance is discussed. The
designed antenna demonstrates antenna gain of 8.2 dB with
omnidirectional far-field radiation pattern in the H-plane. The gain of
the proposed antenna is also compared with the characteristic of the
stand-alone Y-shaped monopole to highlight the advantages of the
proposed approach.
Abstract: In recent years parasitic antenna play major role in
MIMO systems because of their gain and spectral efficiency. In this
paper, single RF chain MIMO transmitter is designed using
reconfigurable parasitic antenna. The Spatial Modulation (SM) is a
recently proposed scheme in MIMO scenario which activates only
one antenna at a time. The SM entirely avoids ICI and IAS, and only
requires a single RF chain at the transmitter. This would switch ON a
single transmit-antenna for data transmission while all the other
antennas are kept silent. The purpose of the parasitic elements is to
change the radiation pattern of the radio waves which is emitted from
the driven element and directing them in one direction and hence
introduces transmit diversity. Diode is connect between the patch and
ground by changing its state (ON and OFF) the parasitic element act
as reflector and director and also capable of steering azimuth and
elevation angle. This can be achieved by changing the input
impedance of each parasitic element through single RF chain. The
switching of diode would select the single parasitic antenna for
spatial modulation. This antenna is expected to achieve maximum
gain with desired efficiency.
Abstract: With the ever-increasing need for wireless communication and the emergence of many systems, it is important to design broadband antennas to cover a wide frequency range. The aim of this paper is to design a broadband patch antenna, employing the three techniques of slotting, adding directly coupled parasitic elements, and fractal EBG structures. The bandwidth is improved from 9.32% to 23.77%. A wideband ranging from 4.15 GHz to 5.27 GHz is obtained. Also a comparative analysis of embedding EBG structures at different heights is also done. The composite effect of integrating these techniques in the design provides a simple and efficient method for obtaining low profile, broadband, high gain antenna. By the addition of parasitic elements the bandwidth was increased to only 18.04%. Later on by embedding EBG structures the bandwidth was increased up to 23.77%. The design is suitable for variety of wireless applications like WLAN and Radar Applications.
Abstract: This paper presents a novel approach for the design of
microwave circuits using Adaptive Network Fuzzy Inference
Optimizer (ANFIO). The method takes advantage of direct synthesis
of subsections of the amplifier using very fast and accurate ANFIO
models based on exact simulations using ADS. A mapping from
course space to fine space known as space mapping is also used. The
proposed synthesis approach takes into account the noise and
scattering parameters due to parasitic elements to achieve optimal
results. The overall ANFIO system is capable of designing different
LNAs at different noise and scattering criteria. This approach offers
significantly reduced time in the design of microwave amplifiers
within the validity range of the ANFIO system. The method has been
proven to work efficiently for a 2.4GHz LNA example. The S21 of
10.1 dB and noise figure (NF) of 2.7 dB achieved for ANFIO while
S21 of 9.05 dB and NF of 2.6 dB achieved for ANN.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.