Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.
Abstract: Modular multiplication is the basic operation
in most public key cryptosystems, such as RSA, DSA, ECC,
and DH key exchange. Unfortunately, very large operands
(in order of 1024 or 2048 bits) must be used to provide
sufficient security strength. The use of such big numbers
dramatically slows down the whole cipher system, especially
when running on embedded processors.
So far, customized hardware accelerators - developed on
FPGAs or ASICs - were the best choice for accelerating
modular multiplication in embedded environments. On the
other hand, many algorithms have been developed to speed
up such operations. Examples are the Montgomery modular
multiplication and the interleaved modular multiplication
algorithms. Combining both customized hardware with
an efficient algorithm is expected to provide a much faster
cipher system.
This paper introduces an enhanced architecture for computing
the modular multiplication of two large numbers X
and Y modulo a given modulus M. The proposed design is
compared with three previous architectures depending on
carry save adders and look up tables. Look up tables should
be loaded with a set of pre-computed values. Our proposed
architecture uses the same carry save addition, but replaces
both look up tables and pre-computations with an enhanced
version of sign detection techniques. The proposed architecture
supports higher frequencies than other architectures.
It also has a better overall absolute time for a single operation.
Abstract: This paper focuses on PSS/E modeling of wind farms
of Doubly-fed Induction Generator (DFIG) type and their impact on
issues of power system operation. Since Wind Turbine Generators
(WTG) don-t have the same characteristics as synchronous
generators, the appropriate modeling of wind farms is essential for
transmission system operators to analyze the best options of
transmission grid reinforcements as well as to evaluate the wind
power impact on reliability and security of supply. With the high
excepted penetration of wind power into the power system a
simultaneous loss of Wind Farm generation will put at risk power
system security and reliability. Therefore, the main wind grid code
requirements concern the fault ride through capability and frequency
operation range of wind turbines. In case of grid faults wind turbines
have to supply a definite reactive power depending on the
instantaneous voltage and to return quickly to normal operation.
Abstract: Background noise is particularly damaging to speech
intelligibility for people with hearing loss especially for sensorineural
loss patients. Several investigations on speech intelligibility have
demonstrated sensorineural loss patients need 5-15 dB higher SNR
than the normal hearing subjects. This paper describes Discrete
Cosine Transform Power Normalized Least Mean Square algorithm
to improve the SNR and to reduce the convergence rate of the LMS
for Sensory neural loss patients. Since it requires only real arithmetic,
it establishes the faster convergence rate as compare to time domain
LMS and also this transformation improves the eigenvalue
distribution of the input autocorrelation matrix of the LMS filter.
The DCT has good ortho-normal, separable, and energy compaction
property. Although the DCT does not separate frequencies, it is a
powerful signal decorrelator. It is a real valued function and thus
can be effectively used in real-time operation. The advantages of
DCT-LMS as compared to standard LMS algorithm are shown via
SNR and eigenvalue ratio computations. . Exploiting the symmetry
of the basis functions, the DCT transform matrix [AN] can be
factored into a series of ±1 butterflies and rotation angles. This
factorization results in one of the fastest DCT implementation. There
are different ways to obtain factorizations. This work uses the fast
factored DCT algorithm developed by Chen and company. The
computer simulations results show superior convergence
characteristics of the proposed algorithm by improving the SNR at
least 10 dB for input SNR less than and equal to 0 dB, faster
convergence speed and better time and frequency characteristics.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.
Abstract: Optimal selection of electrical insulations in electrical
machinery insures reliability during operation. From the insulation
studies of view for electrical machines, stator is the most important
part. This fact reveals the requirement for inspection of the electrical
machine insulation along with the electro-thermal stresses. In the
first step of the study, a part of the whole structure of machine in
which covers the general characteristics of the machine is chosen,
then based on the electromagnetic analysis (finite element method),
the machine operation is simulated. In the simulation results, the
temperature distribution of the total structure is presented
simultaneously by using electro-thermal analysis. The results of
electro-thermal analysis can be used for designing an optimal cooling
system. In order to design, review and comparing the cooling
systems, four wiring structures in the slots of Stator are presented.
The structures are compared to each other in terms of electrical,
thermal distribution and remaining life of insulation by using Finite
Element analysis. According to the steps of the study, an optimization
algorithm has been presented for selection of appropriate structure.
Abstract: We developed a vision interface immersive projection system, CAVE in virtual rea using hand gesture recognition with computer vis background image was subtracted from current webcam and we convert the color space of the imag Then we mask skin regions using skin color range t a noise reduction operation. We made blobs fro gestures were recognized using these blobs. Using recognition, we could implement an effective bothering devices for CAVE. e framework for an reality research field vision techniques. ent image frame age into HSV space. e threshold and apply from the image and ing our hand gesture e interface without
Abstract: Morphological operators transform the original image
into another image through the interaction with the other image of
certain shape and size which is known as the structure element.
Mathematical morphology provides a systematic approach to analyze
the geometric characteristics of signals or images, and has been
applied widely too many applications such as edge detection,
objection segmentation, noise suppression and so on. Fuzzy
Mathematical Morphology aims to extend the binary morphological
operators to grey-level images. In order to define the basic
morphological operations such as fuzzy erosion, dilation, opening
and closing, a general method based upon fuzzy implication and
inclusion grade operators is introduced. The fuzzy morphological
operations extend the ordinary morphological operations by using
fuzzy sets where for fuzzy sets, the union operation is replaced by a
maximum operation, and the intersection operation is replaced by a
minimum operation.
In this work, it consists of two articles. In the first one, fuzzy set
theory, fuzzy Mathematical morphology which is based on fuzzy
logic and fuzzy set theory; fuzzy Mathematical operations and their
properties will be studied in details. As a second part, the application
of fuzziness in Mathematical morphology in practical work such as
image processing will be discussed with the illustration problems.
Abstract: The controllable electrical loss which consists of the
copper loss and iron loss can be minimized by the optimal control of
the armature current vector. The control algorithm of current vector
minimizing the electrical loss is proposed and the optimal current
vector can be decided according to the operating speed and the load
conditions. The proposed control algorithm is applied to the
experimental PM motor drive system and this paper presents a
modern approach of speed control for permanent magnet
synchronous motor (PMSM) applied for Electric Vehicle using a
nonlinear control. The regulation algorithms are based on the
feedback linearization technique. The direct component of the current
is controlled to be zero which insures the maximum torque operation.
The near unity power factor operation is also achieved. More over,
among EV-s motor electric propulsion features, the energy efficiency
is a basic characteristic that is influenced by vehicle dynamics and
system architecture. For this reason, the EV dynamics are taken into
account.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the virgin biomass obtained from hingan shell is used as the feedstock for gasifier to generate producer gas. The gasifier-engine system is operated on diesel and on esters of vegetable oil of hingan in liquid fuel mode operation and then on liquid fuel and producer gas combination in dual fuel mode operation. The performance and emission characteristics of the CI engine is analyzed by running the engine in liquid fuel mode operation and in dual fuel mode operation at different load conditions with respect to maximum diesel savings in the dual fuel mode operation. It was observed that specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine using diesel or hingan oil methyl ester (HOME) is higher than that of dual fuel mode operation. A diesel replacement in the tune of 60% in dual fuel mode is possible with the use of hingan shell producer gas. The emissions parameters such CO, HC, NOx, CO2 and smoke are higher in the case of dual fuel mode of operation as compared to that of liquid fuel mode.
Abstract: This paper presents a low cost automatic system for
sampling the electric field in a limited area. The scanning area is a
flat surface parallel to the ground at a selected height. We discuss
in detail the hardware, software and all the arrangements involved
in the system operation. In order to show the system performance
we include a campaign of narrow band measurements with 6017
sample points in the surroundings of a cellular base station. A
commercial isotropic antenna with three orthogonal axes was used
as sampling device. The results are analyzed in terms of its space
average, standard deviation and statistical distribution.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: This paper discuss the separation of the miscible
liquids by means of fractional distillation. For complete separation of
liquids, the process of heating, condensation, separation and storage
is done automatically to achieve the objective. PIC micro-controller
has been used to control each and every process of the work. The
controller also controls the storage process by activating and deactivating
the conveyors. The liquids are heated which on reaching
their respective boiling points evaporate and enter the condensation
chamber where they convert into liquid. The liquids are then directed
to their respective tanks by means of stepper motor which moves in
three directions, each movement into different tank. The tank on
filling sends the signal to controller which then opens the solenoid
valves. The tank is emptied into the beakers below the nozzle. As the
beaker filled, the nozzle closes and the conveyors come into
operation. The filled beaker is replaced by an empty beaker from
behind. The work can be used in oil industries, chemical industries
and paint industries.
Abstract: The purpose of this study is i) to investigate the driving factors and barriers of the adoption of Information and Communication Technology (ICT) in Halal logistic and ii) to develop an ICT adoption framework for Halal logistic service provider. The Halal LSPs selected for the study currently used ICT service platforms, such as accounting and management system for Halal logistic business. The study categorizes the factors influencing the adoption decision and process by LSPs into four groups: technology related factors, organizational and environmental factors, Halal assurance related factors, and government related factors. The major contribution in this study is the discovery that technology related factors (ICT compatibility with Halal requirement) and Halal assurance related factors are the most crucial factors among the Halal LSPs applying ICT for Halal control in transportation-s operation. Among the government related factors, ICT requirement for monitoring Halal included in Halal Logistic Standard on Transportation (MS2400:2010) are the most influencing factors in the adoption of ICT with the support of the government. In addition, the government related factors are very important in the reducing the main barriers and the creation of the atmosphere of ICT adoption in Halal LSP sector.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.
Abstract: In this paper, a new technique for fast painting with
different colors is presented. The idea of painting relies on applying
masks with different colors to the background. Fast painting is
achieved by applying these masks in the frequency domain instead of
spatial (time) domain. New colors can be generated automatically as a
result from the cross correlation operation. This idea was applied
successfully for faster specific data (face, object, pattern, and code)
detection using neural algorithms. Here, instead of performing cross
correlation between the input input data (e.g., image, or a stream of
sequential data) and the weights of neural networks, the cross
correlation is performed between the colored masks and the
background. Furthermore, this approach is developed to reduce the
computation steps required by the painting operation. The principle of
divide and conquer strategy is applied through background
decomposition. Each background is divided into small in size subbackgrounds
and then each sub-background is processed separately by
using a single faster painting algorithm. Moreover, the fastest painting
is achieved by using parallel processing techniques to paint the
resulting sub-backgrounds using the same number of faster painting
algorithms. In contrast to using only faster painting algorithm, the
speed up ratio is increased with the size of the background when using
faster painting algorithm and background decomposition. Simulation
results show that painting in the frequency domain is faster than that in
the spatial domain.
Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.
Abstract: The NGN (Next Generation Network), which can
provide advanced multimedia services over an all-IP based network, has been the subject of much attention for years. While there have
been tremendous efforts to develop its architecture and protocols, especially for IMS, which is a key technology of the NGN, it is far
from being widely deployed. However, efforts to create an advanced
signaling infrastructure realizing many requirements have resulted in a
large number of functional components and interactions between those
components. Thus, the carriers are trying to explore effective ways to
deploy IMS while offering value-added services. As one such
approach, we have proposed a self-organizing IMS. A self-organizing
IMS enables IMS functional components and corresponding physical
nodes to adapt dynamically and automatically based on situation such
as network load and available system resources while continuing IMS
operation. To realize this, service continuity for users is an important
requirement when a reconfiguration occurs during operation. In this
paper, we propose a mechanism that will provide service continuity to
users and focus on the implementation and describe performance
evaluation in terms of number of control signaling and processing time
during reconfiguration