Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.
Abstract: Cost overruns are a persistent problem in oil and gas
megaprojects. Whilst the extant literature is filled with studies on
incidents and causes of cost overruns, underlying theories to explain
their emergence in oil and gas megaprojects are few. Yet, a way to
contain the syndrome of cost overruns is to understand the bases of
‘how and why’ they occur. Such knowledge will also help to develop
pragmatic techniques for better overall management of oil and gas
megaprojects. The aim of this paper is to explain the development of
cost overruns in hydrocarbon megaprojects through the perspective of
chaos theory. The underlying principles of chaos theory and its
implications for cost overruns are examined and practical
recommendations proposed. In addition, directions for future research
in this fertile area provided.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.
Abstract: Qatar’s primary source of fresh water is through
seawater desalination. Amongst the major processes that are
commercially available on the market, the most common large scale
techniques are Multi-Stage Flash distillation (MSF), Multi Effect
distillation (MED), and Reverse Osmosis (RO). Although commonly
used, these three processes are highly expensive down to high energy
input requirements and high operating costs allied with maintenance
and stress induced on the systems in harsh alkaline media. Beside that
cost, environmental footprint of these desalination techniques are
significant; from damaging marine eco-system, to huge land use, to
discharge of tons of GHG and huge carbon footprint.
Other less energy consuming techniques based on membrane
separation are being sought to reduce both the carbon footprint and
operating costs is membrane distillation (MD).
Emerged in 1960s, MD is an alternative technology for water
desalination attracting more attention since 1980s. MD process
involves the evaporation of a hot feed, typically below boiling point
of brine at standard conditions, by creating a water vapor pressure
difference across the porous, hydrophobic membrane. Main
advantages of MD compared to other commercially available
technologies (MSF and MED) and specially RO are reduction of
membrane and module stress due to absence of trans-membrane
pressure, less impact of contaminant fouling on distillate due to
transfer of only water vapor, utilization of low grade or waste heat
from oil and gas industries to heat up the feed up to required
temperature difference across the membrane, superior water quality,
and relatively lower capital and operating cost.
To achieve the objective of this study, state of the art flat-sheet
cross-flow DCMD bench scale unit was designed, commissioned, and
tested. The objective of this study is to analyze the characteristics and
morphology of the membrane suitable for DCMD through SEM
imaging and contact angle measurement and to study the water
quality of distillate produced by DCMD bench scale unit.
Comparison with available literature data is undertaken where
appropriate and laboratory data is used to compare a DCMD distillate
quality with that of other desalination techniques and standards.
Membrane SEM analysis showed that the PTFE membrane used
for the study has contact angle of 127º with highly porous surface
supported with less porous and bigger pore size PP membrane. Study
on the effect of feed solution (salinity) and temperature on water
quality of distillate produced from ICP and IC analysis showed that
with any salinity and different feed temperature (up to 70ºC) the
electric conductivity of distillate is less than 5 μS/cm with 99.99%
salt rejection and proved to be feasible and effective process capable
of consistently producing high quality distillate from very high feed
salinity solution (i.e. 100000 mg/L TDS) even with substantial
quality difference compared to other desalination methods such as
RO and MSF.
Abstract: Carbon capture, transport and underground storage have become a major solution to reduce CO2 emissions from power plants and other large CO2 sources. A big part of this captured CO2 stream is transported at high pressure dense phase conditions and stored in offshore underground depleted oil and gas fields. CO2 is also transported in offshore pipelines to be used for enhanced oil and gas recovery. The captured CO2 stream with impurities may contain water that causes severe corrosion problems, flow assurance failure and might damage valves and instrumentations. Thus, free water formation should be strictly prevented. The purpose of this work is to study the solubility of water in pure CO2 and in CO2 mixtures under real pipeline pressure (90-150 bar) and temperature operation conditions (5-35°C). A set up was constructed to generate experimental data. The results show the solubility of water in CO2 mixtures increasing with the increase of the temperature or/and with the increase in pressure. A drop in water solubility in CO2 is observed in the presence of impurities. The data generated were then used to assess the capabilities of two mixture models: the GERG-2008 model and the EOS-CG model. By generating the solubility data, this study contributes to determine the maximum allowable water content in CO2 pipelines.
Abstract: The main purpose of this research is to construct a generic model for successful implementation of Total Quality Management (TQM) in Oil sector, and to find out the effects of this model on the organizational sustainability development (OSD) performance of Libyan oil and gas companies using the structured equation modeling (SEM) approach. The research approach covers both quantitative and qualitative methods. A questionnaire was developed in order to identify the quality factors that are seen by Libyan oil and gas companies to be critical to the success of TQM implementation. Hypotheses were developed to evaluate the impact of TQM implementation on O SD. Data analysis reveals that there is a significant positive effect of the TQM implementation on OSD. 24 quality factors are found to be critical and absolutely essential for successful TQM implementation. The results generated a structure of the TQMSD implementation framework based on the four major road map constructs (Top management commitment, employee involvement and participation, customer-driven processes, and continuous improvement culture).
Abstract: In order to fulfill world energy demand, several efforts have been done to look for new and renewable energy candidates to substitute oil and gas. Biomass is one of new and renewable energy sources, which is abundant in Indonesia. Palm kernel shell is a kind of biomass discharge from palm oil industries as a waste. On the other hand, Jatropha curcas that is easy to grow in Indonesia is also a typical energy source either for bio-diesel or biomass. In this study, biomass was used as co-fuel in briquetting of low-rank coal to suppress the release of emission (such as CO, NOx and SOx) during coal combustion. Desulfurizer, CaO-base, was also added to ensure the SOx capture is effectively occurred. Ratio of coal to palm kernel shell (w/w) in the bio-briquette were 50:50, 60:40, 70:30, 80:20 and 90:10, while ratio of calcium to sulfur (Ca/S) in mole/mole were 1:1; 1.25:1; 1.5:1; 1.75:1 and 2:1. The bio-briquette then subjected to physical characterization and combustion test. The results show that the maximum weight loss in the durability measurement was ±6%. In addition, the highest stove efficiency for each desulfurizer was observed at the coal/PKS ratio of 90:10 and Ca/S ratio of 1:1 (except for the scallop shell desulfurizer that appeared at two Ca/S ratios; 1.25:1 and 1.5:1, respectively), i.e. 13.8% for the lime; 15.86% for the oyster shell; 14.54% for the scallop shell and 15.84% for the green mussel shell desulfurizers.
Abstract: This paper presents the result of the implementation of
a series of algorithms intended to be used for representing in most of
the 3D geographic software, even Google Earth, the subsurface
formations properties combining 2D charts or 3D plots over a 3D
background, allowing everyone to use them, no matter the economic
size of the company for which they work. Besides the existence of
complex and expensive specialized software for modeling subsurface
formations based on the same information provided to this one, the
use of this open source development shows a higher and easier
usability and good results, limiting the rendered properties and
polygons to a basic set of charts and tubes.
Abstract: The protection of groundwater resources is the great
important many semiarid and arid environments. Baghan watershed
is located in the north of Kangan in the Boshehr province in Iran. The
groundwater resources have a vital role in supplying agricultural,
drinking, domestic and industrial water demand in Baghan
watershed. For our investigation into the water quality we collected
30 samples to chemical and physical analysis. The result showed the
marl and evaporation deposits that contain anhydrite and gypsum is
the main source of groundwater pollution, and one part of the
groundwater was polluted by oil and gas industrial. Another part of
the groundwater was contaminated by urban waste water. The
electrical conductivity and captions and anions increased around of
towns and gas refinery. Although the negative impact of untreated
domestic wastewater is relatively low but the results showed strongly
the negative impact of wastewater refinery is very considerable. This
negative impact increased in downstream due to shallow aquifer.
Additionally, the agents that adversely affect the quality of
groundwater come from a variety of sources, including geology,
domestic wastewater and the Jam refinery in Baghan watershed.
Abstract: The morphological short-term evolution of Ponta do Tubarão Island (PTI) was investigated through high accurate surveys based on post-processed kinematic (PPK) relative positioning on Global Navigation Satellite Systems (GNSS). PTI is part of a barrier island system on a high energy northeast Brazilian coastal environment and also an area of high environmental sensitivity. Surveys were carried out quarterly over a two years period from May 2010 to May 2012. This paper assesses statically the performance of digital elevation models (DEM) derived from different interpolation methods to represent morphologic features and to quantify volumetric changes and TIN models shown the best results to that purposes. The MDE allowed quantifying surfaces and volumes in detail as well as identifying the most vulnerable segments of the PTI to erosion and/or accumulation of sediments and relate the alterations to climate conditions. The coastal setting and geometry of PTI protects a significant mangrove ecosystem and some oil and gas facilities installed in the vicinities from damaging effects of strong oceanwaves and currents. Thus, the maintenance of PTI is extremely required but the prediction of its longevity is uncertain because results indicate an irregularity of sedimentary balance and a substantial decline in sediment supply to this coastal area.
Abstract: CO2 miscible displacement is not feasible in many oil fields due to high reservoir temperature as higher pressure is required to achieve miscibility. The miscibility pressure is far higher than the formation fracture pressure making it impossible to have CO2 miscible displacement. However, by using oleophilic chemicals, minimum miscibility pressure (MMP) could be lowered. The main objective of this research is to find the best oleophilic chemical in MMP reduction using slim-tube test and Vanishing Interfacial Tension (VIT) The chemicals are selected based on the characteristics that it must be oil soluble, low water solubility, have 4 – 8 carbons, semi polar, economical, and safe for human operation. The families of chemicals chosen are carboxylic acid, alcohol, and ketone. The whole experiment would be conducted at 100°C and the best chemical is said to be effective when it is able to lower CO2-crude oil MMP the most. Findings of this research would have great impact to the oil and gas industry in reduction of operation cost for CO2EOR which is applicable to both onshore and offshore operation.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: In the oil and gas industry, energy prediction can help
the distributor and customer to forecast the outgoing and incoming
gas through the pipeline. It will also help to eliminate any
uncertainties in gas metering for billing purposes. The objective of
this paper is to develop Neural Network Model for energy
consumption and analyze the performance model. This paper
provides a comprehensive review on published research on the
energy consumption prediction which focuses on structures and the
parameters used in developing Neural Network models. This paper is
then focused on the parameter selection of the neural network
prediction model development for energy consumption and analysis
on the result. The most reliable model that gives the most accurate
result is proposed for the prediction. The result shows that the
proposed neural network energy prediction model is able to
demonstrate an adequate performance with least Root Mean Square
Error.
Abstract: Hydrogen sulfide (H2S) is a very toxic gas that is produced in very large quantities in the oil and gas industry. It cannot be flared to the atmosphere and Claus process based gas plants are used to recover the sulfur and convert the hydrogen to water. In this paper, we present optical characterization of an atmospheric pressure microwave plasma torch for H2S dissociation into hydrogen and sulfur. The torch is operated at 2.45 GHz with power up to 2 kW. Three different gases can simultaneously be injected in the plasma torch. Visual imaging and optical emission spectroscopy are used to characterize the plasma for varying gas flow rates and microwave power. The plasma length, emission spectra and temperature are presented. The obtained experimental results validate our earlier published simulation results of plasma torch.
Abstract: A research study was conducted with an objective to propose a collaborative business strategy of a oil and gas trading company, representing PPT Energy Trading Co., Ltd., with its shareholder, especially electricity and power supply companies for LNG Form of Coal Bed Methane in B2B Transaction. Collaborative business strategy is a strategy to collaborate with other organizations due to have future benefits in both parties, or achieve the business objective through the collaboration of business, its strategy and partners. A structured interview was established to collect the required primary data from the company. Not only interview, but also company’s business plan and annual report were collected and analyzed for the company’s current condition. As the result, this research shows a recommendation to propose a new collaborative strategy with limiting its target market, diversifying product, conducting new business model, and considering other stakeholders.
Abstract: There are reports of gas and oil wells fire due to different accidents. Many different methods are used for fire fighting in gas and oil industry. Traditional fire extinguishing techniques are mostly faced with many problems and are usually time consuming and needs lots of equipments. Besides, they cause damages to facilities, and create health and environmental problems. This article proposes innovative approach in fire extinguishing techniques in oil and gas industry, especially applicable for burning oil wells located offshore. Fire extinguishment employing a turbojet is a novel approach which can help to extinguishment the fire in short period of time. Divergent and convergent turbojets modeled in laboratory scale along with a high pressure flame were used. Different experiments were conducted to determine the relationship between output discharges of trumpet and oil wells. The results were corrected and the relationship between dimensionless parameters of flame and fire extinguishment distances and also the output discharge of turbojet and oil wells in specified distances are demonstrated by specific curves.
Abstract: This paper explores the plant maintenance management system that has been used by giant oil and gas company in Malaysia. The system also called as PMMS used to manage the upstream operations for more than 100 plants of the case study company. Moreover, from the observations, focus group discussion with PMMS personnel and application through simulation (SAP R/3), the paper reviews the step-by-step approach and the elements that required for the PMMS. The findings show that the PMMS integrates the overall business strategy in upstream operations that consist of asset management, work management and performance management. In addition, PMMS roles are to help operations personnel organize and plan their daily activities, to improve productivity and reduce equipment downtime and to help operations management analyze the facilities and create performance, and to provide and maintain the operational effectiveness of the facilities.