Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: This research paper deals with the implementation of face recognition using neural network (recognition classifier) on low-resolution images. The proposed system contains two parts, preprocessing and face classification. The preprocessing part converts original images into blurry image using average filter and equalizes the histogram of those image (lighting normalization). The bi-cubic interpolation function is applied onto equalized image to get resized image. The resized image is actually low-resolution image providing faster processing for training and testing. The preprocessed image becomes the input to neural network classifier, which uses back-propagation algorithm to recognize the familiar faces. The crux of proposed algorithm is its beauty to use single neural network as classifier, which produces straightforward approach towards face recognition. The single neural network consists of three layers with Log sigmoid, Hyperbolic tangent sigmoid and Linear transfer function respectively. The training function, which is incorporated in our work, is Gradient descent with momentum (adaptive learning rate) back propagation. The proposed algorithm was trained on ORL (Olivetti Research Laboratory) database with 5 training images. The empirical results provide the accuracy of 94.50%, 93.00% and 90.25% for 20, 30 and 40 subjects respectively, with time delay of 0.0934 sec per image.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Subcritical water extraction was investigated as a
novel and alternative technology in the food and pharmaceutical
industry for the separation of Mannitol from olive leaves and its
results was compared with those of Soxhlet extraction. The effects of
temperature, pressure, and flow rate of water and also momentum
and mass transfer dimensionless variables such as Reynolds and
Peclet Numbers on extraction yield and equilibrium partition
coefficient were investigated. The 30-110 bars, 60-150°C, and flow
rates of 0.2-2 mL/min were the water operating conditions. The
results revealed that the highest Mannitol yield was obtained at
100°C and 50 bars. However, extraction of Mannitol was not
influenced by the variations of flow rate. The mathematical modeling
of experimental measurements was also investigated and the model is
capable of predicting the experimental measurements very well. In
addition, the results indicated higher extraction yield for the
subcritical water extraction in contrast to Soxhlet method.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: We estimate snow velocity and snow drift density on hilly terrain under the assumption that the drifting snow mass can be represented using a micro-continuum approach (i.e. using a nonclassical mechanics approach assuming a class of fluids for which basic equations of mass, momentum and energy have been derived). In our model, the theory of coupled stress fluids proposed by Stokes [1] has been employed for the computation of flow parameters. Analyses of bulk drift velocity, drift density, drift transport and mass transport of snow particles have been carried out and computations made, considering various parametric effects. Results are compared with those of classical mechanics (logarithmic wind profile). The results indicate that particle size affects the flow characteristics significantly.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: Modeling of a heterogeneous industrial fixed bed
reactor for selective dehydrogenation of heavy paraffin with Pt-Sn-
Al2O3 catalyst has been the subject of current study. By applying
mass balance, momentum balance for appropriate element of reactor
and using pressure drop, rate and deactivation equations, a detailed
model of the reactor has been obtained. Mass balance equations have
been written for five different components. In order to estimate
reactor production by the passage of time, the reactor model which is
a set of partial differential equations, ordinary differential equations
and algebraic equations has been solved numerically.
Paraffins, olefins, dienes, aromatics and hydrogen mole percent as
a function of time and reactor radius have been found by numerical
solution of the model. Results of model have been compared with
industrial reactor data at different operation times. The comparison
successfully confirms validity of proposed model.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: A systematic way to derive the conserved quantities for the axisymmetric liquid jet, free jet and wall jet using conservation laws is presented. The flow in axisymmetric jets is governed by Prandtl-s momentum boundary layer equation and the continuity equation. The multiplier approach is used to construct a basis of conserved vectors for the system of two partial differential equations for the two velocity components. The basis consists of two conserved vectors. By integrating the corresponding conservation laws across the jet and imposing the boundary conditions, conserved quantities are derived for the axisymmetric liquid and free jet. The multiplier approach applied to the third-order partial differential equation for the stream function yields two local conserved vectors one of which is a non-local conserved vector for the system. One of the conserved vectors gives the conserved quantity for the axisymmetric free jet but the conserved quantity for the wall jet is not obtained from the second conserved vector. The conserved quantity for the axisymmetric wall jet is derived from a non-local conserved vector of the third-order partial differential equation for the stream function. This non-local conserved vector for the third-order partial differential equation for the stream function is obtained by using the stream function as multiplier.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible thermal multi-component gas
mixture flows in pipes. The set of the mass, momentum and enthalpy
conservation equations for gas phase is solved. Thermo-physical
properties of multi-component gas mixture are calculated by solving
the Equation of State (EOS) model. The Soave-Redlich-Kwong
(SRK-EOS) model is chosen. Gas mixture viscosity is calculated on
the basis of the Lee-Gonzales-Eakin (LGE) correlation. Numerical
analysis on rapid decompression in conventional dry gases is
performed by using the proposed mathematical model. The model is
validated on measured values of the decompression wave speed in
dry natural gas mixtures. All predictions show excellent agreement
with the experimental data at high and low pressure. The presented
model predicts the decompression in dry natural gas mixtures much
better than GASDECOM and OLGA codes, which are the most
frequently-used codes in oil and gas pipeline transport service.
Abstract: The present contribution deals with the
thermophoretic deposition of nanoparticles over a rapidly rotating
permeable disk in the presence of partial slip, magnetic field, thermal
radiation, thermal-diffusion, and diffusion-thermo effects. The
governing nonlinear partial differential equations such as continuity,
momentum, energy and concentration are transformed into nonlinear
ordinary differential equations using similarity analysis, and the
solutions are obtained through the very efficient computer algebra
software MATLAB. Graphical results for non-dimensional
concentration and temperature profiles including thermophoretic
deposition velocity and Stanton number (thermophoretic deposition
flux) in tabular forms are presented for a range of values of the
parameters characterizing the flow field. It is observed that slip
mechanism, thermal-diffusion, diffusion-thermo, magnetic field and
radiation significantly control the thermophoretic particles deposition
rate. The obtained results may be useful to many industrial and
engineering applications.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe