Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: This paper presents a speed fuzzy sliding mode
controller for a vector controlled induction machine (IM) fed by a
voltage source inverter (PWM).
The sliding mode based fuzzy control method is developed to
achieve fast response, a best disturbance rejection and to maintain a
good decoupling.
The problem with sliding mode control is that there is high
frequency switching around the sliding mode surface. The FSMC is
the combination of the robustness of Sliding Mode Control (SMC)
and the smoothness of Fuzzy Logic (FL). To reduce the torque
fluctuations (chattering), the sign function used in the conventional
SMC is substituted with a fuzzy logic algorithm.
The proposed algorithm was simulated by Matlab/Simulink
software and simulation results show that the performance of the
control scheme is robust and the chattering problem is solved.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: Photovoltaic (PV) systems provides a viable means of
power generation for applications like powering residential
appliances, electrification of villages in rural areas, refrigeration and
water pumping. Photovoltaic-power generation is reliable. The
operation and maintenance costs are very low. Since Myanmar is a
land of plentiful sunshine, especially in central and southern regions
of the country, the solar energy could hopefully become the final
solution to its energy supply problem in rural area.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: This paper presents design and implements the
T-DOF PI controller design for a speed control of induction motor.
The voltage source inverter type space vector pulse width modulation
technique is used the drive system. This scheme leads to be able to
adjust the speed of the motor by control the frequency and amplitude
of the input voltage. The ratio of input stator voltage to frequency
should be kept constant. The T-DOF PI controller design by root
locus technique is also introduced to the system for regulates and
tracking speed response. The experimental results in testing the 120
watt induction motor from no-load condition to rated condition show
the effectiveness of the proposed control scheme.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: This paper proposes an effective algorithm approach to hybrid control systems combining fuzzy logic and conventional control techniques of controlling the speed of induction motor assumed to operate in high-performance drives environment. The introducing of fuzzy logic in the control systems helps to achieve good dynamical response, disturbance rejection and low sensibility to parameter variations and external influences. Some fundamentals of the fuzzy logic control are preliminary illustrated. The developed control algorithm is robust, efficient and simple. It also assures precise trajectory tracking with the prescribed dynamics. Experimental results have shown excellent tracking performance of the proposed control system, and have convincingly demonstrated the validity and the usefulness of the hybrid fuzzy controller in high-performance drives with parameter and load uncertainties. Satisfactory performance was observed for most reference tracks.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: This paper presents a dynamic model for mechanical
loads of an electric drive, including angular misalignment and
including load unbalance. The misalignment model represents the
effects of the universal joint between the motor and the mechanical
load. Simulation results are presented for an induction motor driving
a mechanical load with angular misalignment for both flexible and
rigid coupling. The models presented are very useful in the study of
mechanical fault detection in induction motors, using mechanical and
electrical signals already available in a drive system, such as speed,
torque and stator currents.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.