Abstract: Here, we study the characteristic feature of
conventional (ON-OFF keying) and soliton based transmission
system. We consider 20Gbps transmission system implemented with
Conventional Single Mode Fiber (C-SMF) to examine the role of
Gaussian pulse which is the characteristic of conventional
propagation and Hyperbolic-secant pulse which is the characteristic
of soliton propagation in it. We note the influence of these pulses
with respect to different dispersion lengths and soliton period in
conventional and soliton system respectively and evaluate the system
performance in terms of Quality factor. From the analysis, we could
prove that the soliton pulse has the consistent performance even for
long distance without dispersion compensation than the conventional
system as it is robust to dispersion. For the length of transmission of
200Km, soliton system yielded Q of 33.958 while the conventional
system totally exhausted with Q=0.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: Dental porcelain composites reinforced and toughened
by 20 wt.% tetragonal zirconia (3Y-TZP) were processed by hot
pressing at 1000°C. Two types of particles were tested: yttriastabilized
zirconia (ZrO2–3%Y2O3) agglomerates and pre-sintered
yttria-stabilized zirconia (ZrO2–3%Y2O3) particles. The composites
as well as the reinforcing particles were analyzed by the means of
optical and Scanning Electron Microscopy (SEM), Energy Dispersion
Spectroscopy (EDS) and X-Ray Diffraction (XRD). The mechanical
properties were obtained by the transverse rupture strength test. Wear
tests were also performed on the composites and monolithic
porcelain. The best mechanical results were displayed by the
porcelain reinforced with the pre-sintered ZrO2–3%Y2O3
agglomerates.
Abstract: Surface modification and functionalization has been
an important tool for scientists in order to open new frontiers in
nanoscience and nanotechnology. Desired surface characteristics for
the intended applications can be achieved with surface
functionalization.
In this work, the effect of water soluble ligands on the adsorption
capabilities of silver nanoparticles onto AC which was synthesized
from German beech wood was investigated. Sodium borohydride
(NaBH4) and polyvinyl alcohol (PVA) were used as the ligands.
Silver nanoparticles with different surface coatings have average
sizes range from 10 to 13 nm. They were synthesized in aqueous
media by reducing Ag (I) ion in the presence of ligands. These
particles displayed adsorption tendencies towards AC when they
were mixed together and shaken in distilled water.
Silver nanoparticles (NaBH4-AgNPs) reduced and stabilized by
NaBH4 adsorbed onto AC with a homogenous dispersion of
aggregates with sizes in the range of 100-400 nm. Beside, silver
nanoparticles, which were prepared in the presence of both NaBH4
and PVA (NaBH4/PVA-Ag NPs), demonstrated that NaBH4/PVA-Ag
NPs adsorbed and dispersed homogenously but, they aggregated with
larger sizes on the AC surface (range from 300 to 600 nm). In
addition, desorption resistance of Ag nanoparticles were investigated
in distilled water. According to the results AgNPs were not desorbed
on the AC surface in distilled water.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: This paper focuses on the assessment of the air
pollution and morbidity relationship in Tunisia. Air pollution is
measured by ozone air concentration and the morbidity is measured
by the number of respiratory-related restricted activity days during
the 2-week period prior to the interview. Socioeconomic data are also
collected in order to adjust for any confounding covariates. Our
sample is composed by 407 Tunisian respondents; 44.7% are women,
the average age is 35.2, near 69% are living in a house built after
1980, and 27.8% have reported at least one day of respiratory-related
restricted activity. The model consists on the regression of the
number of respiratory-related restricted activity days on the air
quality measure and the socioeconomic covariates. In order to correct
for zero-inflation and heterogeneity, we estimate several models
(Poisson, negative binomial, zero inflated Poisson, Poisson hurdle,
negative binomial hurdle and finite mixture Poisson models).
Bootstrapping and post-stratification techniques are used in order to
correct for any sample bias. According to the Akaike information
criteria, the hurdle negative binomial model has the greatest goodness
of fit. The main result indicates that, after adjusting for
socioeconomic data, the ozone concentration increases the probability
of positive number of restricted activity days.
Abstract: Photonic Crystal Fibers (PCFs) can be used in optical
communications as transmission lines. For this reason, the PCFs with
low confinement loss, low chromatic dispersion, and low nonlinear
effects are highly suitable transmission media. In this paper, we
introduce a new design of index-guiding nanostructured photonic
crystal fiber (IG-NPCF) with ultra-low chromatic dispersion, low
nonlinearity effects, and low confinement loss. Relatively low
dispersion is achieved in the wavelength range of 1200 to 1600nm
using the proposed design. According to the new structure of
nanostructured PCF presented in this study, the chromatic dispersion
slope is -30(ps/km.nm) and the confinement loss reaches below 10-7
dB/km. While in the wavelength range mentioned above at the same
time an effective area of more than 50.2μm2 is obtained.
Abstract: Particles exhausted from cars have adverse impacts on
human health. The study developed a three-dimensional particle
dispersion numerical model including particle coagulation to simulate
the particle concentration distribution under idling conditions in a
residential underground garage. The simulation results demonstrate
that particle disperses much faster in the vertical direction than that in
horizontal direction. The enhancement of particle dispersion in the
vertical direction due to the increase of cars with engine running is
much stronger than that in the car exhaust direction. Particle dispersion
from each pair of adjacent cars has little influence on each other in the
study. Average particle concentration after 120 seconds exhaust is
1.8-4.5 times higher than the initial total particles at ambient
environment. Particle pollution in the residential underground garage
is severe.
Abstract: This paper presents nonlinear pulse propagation characteristics for different input optical pulse shapes with various input pulse energy levels in semiconductor optical amplifiers. For simulation of nonlinear pulse propagation, finite-difference beam propagation method is used to solve the nonlinear Schrödinger equation. In this equation, gain spectrum dynamics, gain saturation are taken into account which depends on carrier depletion, carrier heating, spectral-hole burning, group velocity dispersion, self-phase modulation and two photon absorption. From this analysis, we obtained the output waveforms and spectra for different input pulse shapes as well as for different input energies. It shows clearly that the peak position of the output waveforms are shifted toward the leading edge which due to the gain saturation of the SOA for higher input pulse energies. We also analyzed and compared the normalized difference of full-width at half maximum for different input pulse shapes in the SOA.
Abstract: In this study, epoxy composite specimens reinforced
with multi-walled carbon nanotube filler were fabricated using shear
mixer and ultra-sonication processor. The mechanical and thermal
properties of the fabricated specimens were measured and evaluated.
From the electron microscope images and the results from the
measurements of tensile strengths, the specimens having 0.6 wt%
nanotube content show better dispersion and higher strength than those
of the other specimens. The Young’s moduli of the specimens
increased as the contents of the nanotube filler in the matrix were
increased. The specimen having a 0.6 wt% nanotube filler content
showed higher thermal conductivity than that of the other specimens.
While, in the measurement of thermal expansion, specimens having
0.4 and 0.6 wt% filler contents showed a lower value of thermal
expansion than that of the other specimens. On the basis of the
measured and evaluated properties of the composites, we believe that
the simple and time-saving fabrication process used in this study was
sufficient to obtain improved properties of the specimens.
Abstract: We model and simulate the combined effect of fiber
dispersion and frequency chirp of a directly modulated high-speed
laser diode on the figures of merit of a non-amplified 40-Gbps optical
fiber link. We consider both the return to zero (RZ) and non-return to
zero (NRZ) patterns of the pseudorandom modulation bits. The
performance of the fiber communication system is assessed by the
fiber-length limitation due to the fiber dispersion. We study the
influence of replacing standard single-mode fibers by non-zero
dispersion-shifted fibers on the maximum fiber length and evaluate
the associated power penalty. We introduce new dispersion
tolerances for 1-dB power penalty of the RZ and NRZ 40-Gbps
optical fiber links.
Abstract: We have experimentally demonstrated bright-dark
pulses in a nonlinear polarization rotation (NPR) based mode-locked
Erbium-doped fiber laser (EDFL) with a long cavity configuration.
Bright–dark pulses could be achieved when the laser works in the
passively mode-locking regime and the net group velocity dispersion
is quite anomalous. The EDFL starts to generate a bright pulse train
with degenerated dark pulse at the mode-locking threshold pump
power of 35.09 mW by manipulating the polarization states of the
laser oscillation modes using a polarization controller (PC). A split
bright–dark pulse is generated when further increasing the pump
power up to 37.95 mW. Stable bright pulses with no obvious
evidence of a dark pulse can also be generated when further adjusting
PC and increasing the pump power up to 52.19 mW. At higher pump
power of 54.96 mW, a new form of bright-dark pulse emission was
successfully identified with the repetition rate of 29 kHz. The bright
and dark pulses have a duration of 795.5 ns and 640 ns, respectively.
Abstract: Aluminum hybrid reinforcement technology is a
response to the dynamic ever increasing service requirements of such
industries as transportation, aerospace, automobile, marine, etc. It is
unique in that it offers a platform of almost unending combinations of
materials to produce various hybrid composites. This article reviews
the studies carried out on various combinations of aluminum hybrid
composite and the effects on mechanical, physical and chemical
properties. It is observed that the extent of enhancement of these
properties of hybrid composites is strongly dependent on the nature
of the reinforcement, its hardness, particle size, volume fraction,
uniformity of dispersion within the matrix and the method of hybrid
production.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Load carrying capacity of an oil lubricated two-axial
groove journal bearing is simulated by taking into account the
viscosity variations in lubricant due to the addition of TiO2
nanoparticles as lubricant additive. Shear viscosities of TiO2
nanoparticle dispersions in oil are measured for various nanoparticle
additive concentrations. The viscosity model derived from the
experimental viscosities is employed in a modified Reynolds
equation to obtain the pressure profiles and load carrying capacity of
two-axial groove journal bearing. Results reveal an increase in load
carrying capacity of bearings operating on nanoparticle dispersions as
compared to plain oil.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: Fluid rheology may have essential impact on sound propagation in a liquid-filled pipe, especially, in a low frequency range. Rheological parameters of liquid are temperature-sensitive, which ultimately results in a temperature dependence of the wave speed and attenuation in the waveguide. The study is devoted to modeling of this effect at sound propagation in an elastic pipe with polymeric liquid, described by generalized Maxwell model with non-zero high-frequency viscosity. It is assumed that relaxation spectrum is distributed according to the Spriggs law; temperature impact on the liquid rheology is described on the basis of the temperature-superposition principle and activation theory. The dispersion equation for the waveguide, considered as a thin-walled tube with polymeric solution, is obtained within a quasi-one-dimensional formulation. Results of the study illustrate the influence of temperature on sound propagation in the system.
Abstract: The most important problem occurs on oil spills in sea
water is to reduce the oil spills size. This study deals with the
development of high pressurized nozzle using dispersion method for
oil leakage in offshore. 3D numerical simulation results were
obtained using ANSYS Fluent 13.0 code and correlate with the
experimental data for validation. This paper studies the contribution
of the process on flow speed and pressure of the flow from two
different geometrical designs of nozzles and to generate a spray
pattern suitable for dispersant application. Factor of size distribution
of droplets generated by the nozzle is calculated using pressures
ranging from 2 to 6 bars. Results obtain from both analyses shows a
significant spray pattern and flow distribution as well as distance.
Results also show a significant contribution on the effect of oil
leakage in terms of the diameter of the oil spills break up.