Abstract: FlexRay, as a communication protocol for automotive
control systems, is developed to fulfill the increasing demand on the
electronic control units for implementing systems with higher safety
and more comfort. In this work, we study the impact of
radiation-induced soft errors on FlexRay-based steer-by-wire system.
We injected the soft errors into general purpose register set of FlexRay
nodes to identify the most critical registers, the failure modes of the
steer-by-wire system, and measure the probability distribution of
failure modes when an error occurs in the register file.
Abstract: An approach of design of stable of control systems with ultimately wide ranges of uncertainly disturbed parameters is offered. The method relies on using of nonlinear structurally stable functions from catastrophe theory as controllers. Theoretical part presents an analysis of designed nonlinear second-order control systems. As more important the integrators in series, canonical controllable form and Jordan forms are considered. The analysis resumes that due to added controllers systems become stable and insensitive to any disturbance of parameters. Experimental part presents MATLAB simulation of design of control systems of epidemic spread, aircrafts angular motion and submarine depth. The results of simulation confirm the efficiency of offered method of design. KeywordsCatastrophes, robust control, simulation, uncertain parameters.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: Fiber optic sensor technology offers the possibility of
sensing different parameters like strain, temperature, pressure in
harsh environment and remote locations. these kinds of sensors
modulates some features of the light wave in an optical fiber such an
intensity and phase or use optical fiber as a medium for transmitting
the measurement information.
The advantages of fiber optic sensors in contrast to conventional
electrical ones make them popular in different applications and now a
day they consider as a key component in improving industrial
processes, quality control systems, medical diagnostics, and
preventing and controlling general process abnormalities.
This paper is an introduction to fiber optic sensor technology and
some of the applications that make this branch of optic technology,
which is still in its early infancy, an interesting field.
Abstract: The typical coupled-tanks process that is TITO
plant has the difficulty in controller design because changing
of system dynamics and interacting of process. This paper
presents design methodology of auto-adjustable PI controller
using MRAC technique. The proposed method can adjust the
controller parameters in response to changes in plant and
disturbance real time by referring to the reference model that
specifies properties of the desired control system.
Abstract: This paper presents a fuzzy control system for a three degree of freedom (3-DOF) stabilized platform with explicit decoupling scheme. The system under consideration is a system with strong interactions between three channels. By using the concept of decentralized control, a control structure is developed that is composed of three control loops, each of which is associated with a single-variable fuzzy controller and a decoupling unit. Takagi-Sugeno (TS) fuzzy control algorithm is used to implement the fuzzy controller. The decoupling units design is based on the adaptive theory reasoning. Simulation tests were established using Simulink of Matlab. The obtained results have demonstrated the feasibility and effectiveness of the proposed approach. Simulation results are represented in this paper.
Abstract: In automotive systems almost all steps concerning the
calibration of several control systems, e.g., low idle governor or
boost pressure governor, are made with the vehicle because the timeto-
production and cost requirements on the projects do not allow for
the vehicle analysis necessary to build reliable models. Here is
presented a procedure using parametric and NN (neural network)
models that enables the generation of vehicle system models based
on normal ECU engine control unit) vehicle measurements. These
models are locally valid and permit pre and follow-up calibrations so
that, only the final calibrations have to be done with the vehicle.
Abstract: Flexible manufacturing system is a system that is able to respond to changed conditions. In general, this flexibility is divided into two key categories and several subcategories. The first category is the so called machine flexibility which enables to make various products by the given machinery. The second category is routing flexibility enabling to execute the same operation by various machines. Flexible manufacturing systems usually consist of three main parts: CNC machine tools, transport system and control system. A higher level of flexible manufacturing systems is represented by the so called intelligent manufacturing systems.
Abstract: A model-free robust control (MFRC) approach is proposed for position control of robot manipulators in the state space. The control approach is verified analytically to be robust subject to uncertainties including external disturbances, unmodeled dynamics, and parametric uncertainties. There is a high flexibility to work on different systems including actuators by the use of the proposed control approach. The proposed control approach can guarantee the robustness of control system. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a satisfactory performance for control system under technical specifications. KeywordsModel-free, robust control, position control, PUMA 560.
Abstract: The authors present optimization parameters of rotary
positioner controller in hard disk drive servo track writing process
using coefficient diagram method; CDM. Due to estimation
parameters in PI Positioning Control System by expected ratio
method cannot meet the required specification of response
effectively, we suggest coefficient diagram method for defining
controller parameters under the requirement of the system. Finally,
the simulation results show that our proposed method can improve
the problem in tuning parameter of rotary positioner controller. It is
satisfied specification of performance of control system. Furthermore,
it is very convenient as a fast adjustment damping ratio as well as a
high speed response.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: In this paper application of artificial intelligence for
baby and children caring is studied. Then a new idea for injury
prevention and safety announcement is presented by using digital
image processing. The paper presents the structure of the proposed
system. The system determines the possibility of the dangers for
children and babies in yards, gardens and swimming pools or etc. In
the presented idea, multi camera System is used and receiver videos
are processed to find the hazardous areas then the entrance of
children and babies in the determined hazardous areas are analyzed.
In this condition the system does the programmed action capture,
produce alarm or tone or send message.
Abstract: Information on weed distribution within the field is
necessary to implement spatially variable herbicide application.
Since hand labor is costly, an automated weed control system could be
feasible. This paper deals with the development of an algorithm for
real time specific weed recognition system based on Histogram
Analysis of an image that is used for the weed classification. This
algorithm is specifically developed to classify images into broad and
narrow class for real-time selective herbicide application. The
developed system has been tested on weeds in the lab, which have
shown that the system to be very effectiveness in weed identification.
Further the results show a very reliable performance on images of
weeds taken under varying field conditions. The analysis of the results
shows over 95 percent classification accuracy over 140 sample images
(broad and narrow) with 70 samples from each category of weeds.
Abstract: In the present article, a new method has been developed to enhance the application of equipment monitoring, which in turn results in improving condition-based maintenance economic impact in an automobile parts manufacturing factory. This study also describes how an effective software with a simple database can be utilized to achieve cost-effective improvements in maintenance performance. The most important results of this project are indicated here: 1. 63% reduction in direct and indirect maintenance costs. 2. Creating a proper database to analyse failures. 3. Creating a method to control system performance and develop it to similar systems. 4. Designing a software to analyse database and consequently create technical knowledge to face unusual condition of the system. Moreover, the results of this study have shown that the concept and philosophy of maintenance has not been understood in most Iranian industries. Thus, more investment is strongly required to improve maintenance conditions.
Abstract: This paper shows a new method for design of fuzzy observers for Takagi-Sugeno systems. The method is based on Linear matrix inequalities (LMIs) and it allows to insert H constraint into the design procedure. The speed of estimation can tuned be specification of a decay rate of the observer closed loop system. We discuss here also the influence of parametric uncertainties at the output control system stability.
Abstract: In this paper, the process of obtaining Q and R
matrices for optimal pitch aircraft control system has been described.
Since the innovation of optimal control method, the determination of
Q and R matrices for such system has not been fully specified. The
value of Q and R for optimal pitch aircraft control application, have
been simulated and calculated. The suitable results for Q and R have
been observed through the performance index (PI). If the PI is small
“enough", we would say the Q & R values are suitable for that
certain type of optimal control system. Moreover, for the same value
of PI, we could have different Q and R sets. Due to the rule-free
determination of Q and R matrices, a specific method is brought to
find out the rough value of Q and R referring to rather small value of
PI.
Abstract: Efforts to secure supervisory control and data acquisition
(SCADA) systems must be supported under the guidance of
sound security policies and mechanisms to enforce them. Critical
elements of the policy must be systematically translated into a format
that can be used by policy enforcement components. Ideally, the
goal is to ensure that the enforced policy is a close reflection of
the specified policy. However, security controls commonly used to
enforce policies in the IT environment were not designed to satisfy
the specific needs of the SCADA environment. This paper presents
a language, based on the well-known XACML framework, for the
expression of authorization policies for SCADA systems.
Abstract: Keystroke authentication is a new access control system
to identify legitimate users via their typing behavior. In this paper,
machine learning techniques are adapted for keystroke authentication.
Seven learning methods are used to build models to differentiate user
keystroke patterns. The selected classification methods are Decision
Tree, Naive Bayesian, Instance Based Learning, Decision Table, One
Rule, Random Tree and K-star. Among these methods, three of them
are studied in more details. The results show that machine learning
is a feasible alternative for keystroke authentication. Compared to
the conventional Nearest Neighbour method in the recent research,
learning methods especially Decision Tree can be more accurate. In
addition, the experiment results reveal that 3-Grams is more accurate
than 2-Grams and 4-Grams for feature extraction. Also, combination
of attributes tend to result higher accuracy.