Abstract: In the present study, the rate of NOx emission in a
combustion chamber working in conventional combustion and High
Temperature Air Combustion (HiTAC) system are examined using
CFD modeling. The effect of peak temperature, combustion air
temperature and oxygen concentration on NOx emission rate was
undertaken. Results show that in a fixed oxygen concentration,
increasing the preheated air temperature will increase the peak
temperature and NOx emission rate. In addition, it was observed that
the reduction of the oxygen concentration in the fixed preheated air
temperature decreases the peak temperature and NOx emission rate.
On the other hand, the results show that increase of preheated air
temperature at various oxygen concentrations increases the NOx
emission rate. However, the rate of increase in HiTAC conditions is
quite lower than the conventional combustion. The modeling results
show that the NOx emission rate in HiTAC combustion is 133% less
than that of the conventional combustion.
Abstract: Surface sediment samples were collected from the
Canon River mouth, Taiwan and analyzed for polycyclic aromatic
hydrocarbons (PAHs). Total PAHs concentrations varied from 337 to
1,252 ng/g dry weight, with a mean concentration of 827 ng/g dry
weight. The spatial distribution of PAHs reveals that the PAHs
concentration is relatively high in the river mouth region, and
gradually diminishes toward the harbor region. Diagnostic ratios
showed that the possible source of PAHs in the Canon River mouth
could be petroleum combustion. The toxic equivalent concentrations
(TEQcarc) of PAHs varied from 47 to 112 ng TEQ/g dry weight. Higher
total TEQcarc values were found in the river mouth region. As
compared with the US Sediment Quality Guidelines (SQGs), the
observed levels of PAHs at Canon River mouth were lower than the
effects range low (ERL), and would probably not exert adverse
biological effects.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Incompressible Navier-Stokes equations are reviewed
in this work. Three-dimensional Navier-Stokes equations are solved
analytically. The Mathematical derivation shows that the solutions
for the zero and constant pressure gradients are similar. Descriptions
of the proposed formulation and validation against two laminar
experiments and three different turbulent flow cases are reported in
this paper. Even though, the analytical solution is derived for nonreacting
flows, it could reproduce trends for cases including
combustion.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.