Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: This research aimed to study the competency of health
and wellness hotels and resorts in developing use the local natural
resources and wisdom to conform to the national health and wellness
tourism (HWT) strategy by comparing two independent samples,
from Aumpur Muang, Ranong province and Aumpur Muang,
Chiangmai province. And also study in the suggestive direct path to
lead the organization to the sustainable successful.
This research was conduct by using mix methodology; both
quantitative and qualitative data were used. The data of competency
of health and wellness hotels and resorts (HWHR) in developing use
the local natural resources for HWT promoting were collected via
300 set of questionnaires, from 6 hotels and resorts in 2 areas, 3
places from Aumpur Muang, Ranong province and another 3 from
Aumpur Muang, Chiangmai province.
Thestudy of HWHR’s competency in developing use the local
natural resources and wisdom to conform to the national HWT
strategycan be divided into fourmain areas, food and beverages
service, tourism activity, environmental service, and value adding.
The total competency of the Chiangmai sample is importantly
scoredp. value 0.01 higher than the Ranong one while the area of
safety, Chiangmai’s competency is importantly scored 0.05 higher
than the Ranong’scompetency. Others were rated not differently.
Since Chiangmai perform better, then it can be a role model in
developing HTHR or HWT destination.
From the part of qualitative research, content analysis of business
contents and its environments were analyzed. The four stages of
strategic development and plans, from the smallest scale to the largest
scale such a national base were discussed. The HWT: Evolution
model and strategy for lodging Business were suggested. All those
stages must work harmoniously together. The distinctive result
illustrates the need of human resource development as the key point
to create the identity of Thainess on Health and wellness service
providing. This will add-on the value of services and differentiates
ourselves from other competitors. The creative of Thailand’s health
and wellness brand possibly increase loyalty customers which agreed
to be a path of sustainable development.
Abstract: One of the main image representations in Mathematical Morphology is the 3D Shape Decomposition Representation, useful for Image Compression and Representation,and Pattern Recognition. The 3D Morphological Shape Decomposition representation can be generalized a number of times,to extend the scope of its algebraic characteristics as much as possible. With these generalizations, the Morphological Shape Decomposition 's role to serve as an efficient image decomposition tool is extended to grayscale images.This work follows the above line, and further develops it. Anew evolutionary branch is added to the 3D Morphological Shape Decomposition's development, by the introduction of a 3D Multi Structuring Element Morphological Shape Decomposition, which permits 3D Morphological Shape Decomposition of 3D binary images (grayscale images) into "multiparameter" families of elements. At the beginning, 3D Morphological Shape Decomposition representations are based only on "1 parameter" families of elements for image decomposition.This paper addresses the gray scale inter frame interpolation by means of mathematical morphology. The new interframe interpolation method is based on generalized morphological 3D Shape Decomposition. This article will present the theoretical background of the morphological interframe interpolation, deduce the new representation and show some application examples.Computer simulations could illustrate results.
Abstract: The tray/multi-tray distillation process is a topic that
has been investigated to great detail over the last decade by many
teams such as Jubran et al. [1], Adhikari et al. [2], Mowla et al. [3],
Shatat et al. [4] and Fath [5] to name a few. A significant amount of
work and effort was spent focusing on modeling and/simulation of
specific distillation hardware designs. In this work, we have focused
our efforts on investigating and gathering experimental data on
several engineering and design variables to quantify their influence
on the yield of the multi-tray distillation process. Our goals are to
generate experimental performance data to bridge some existing gaps
in the design, engineering, optimization and theoretical modeling
aspects of the multi-tray distillation process.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: In April 2009, a new variant of Influenza A virus
subtype H1N1 emerged in Mexico and spread all over the world. The
influenza has three subtypes in human (H1N1, H1N2 and H3N2)
Types B and C influenza tend to be associated with local or regional
epidemics. Preliminary genetic characterization of the influenza
viruses has identified them as swine influenza A (H1N1) viruses.
Nucleotide sequence analysis of the Haemagglutinin (HA) and
Neuraminidase (NA) are similar to each other and the majority of
their genes of swine influenza viruses, two genes coding for the
neuraminidase (NA) and matrix (M) proteins are similar to
corresponding genes of swine influenza. Sequence similarity between
the 2009 A (H1N1) virus and its nearest relatives indicates that its
gene segments have been circulating undetected for an extended
period. Nucleic acid sequence Maximum Likelihood (MCL) and
DNA Empirical base frequencies, Phylogenetic relationship amongst
the HA genes of H1N1 virus isolated in Genbank having high
nucleotide sequence homology.
In this paper we used 16 HA nucleotide sequences from NCBI for
computing sequence relationships similarity of swine influenza A
virus using the following method MCL the result is 28%, 36.64% for
Optimal tree with the sum of branch length, 35.62% for Interior
branch phylogeny Neighber – Join Tree, 1.85% for the overall
transition/transversion, and 8.28% for Overall mean distance.
Abstract: This work deals with modeling and simulation of SO2 removal in a ceramic membrane by means of FEM. A mass transfer model was developed to predict the performance of SO2 absorption in a chemical solvent. The model was based on solving conservation equations for gas component in the membrane. Computational fluid dynamics (CFD) of mass and momentum were used to solve the model equations. The simulations aimed to obtain the distribution of gas concentration in the absorption process. The effect of the operating parameters on the efficiency of the ceramic membrane was evaluated. The modeling findings showed that the gas phase velocity has significant effect on the removal of gas whereas the liquid phase does not affect the SO2 removal significantly. It is also indicated that the main mass transfer resistance is placed in the membrane and gas phase because of high tortuosity of the ceramic membrane.
Abstract: From a set of shifted, blurred, and decimated image , super-resolution image reconstruction can get a high-resolution image. So it has become an active research branch in the field of image restoration. In general, super-resolution image restoration is an ill-posed problem. Prior knowledge about the image can be combined to make the problem well-posed, which contributes to some regularization methods. In the regularization methods at present, however, regularization parameter was selected by experience in some cases and other techniques have too heavy computation cost for computing the parameter. In this paper, we construct a new super-resolution algorithm by transforming the solving of the System stem Є=An into the solving of the equations X+A*X-1A=I , and propose an inverse iterative method.
Abstract: In this paper we have proposed a methodology to
develop an amperometric biosensor for the analysis of glucose
concentration using a simple microcontroller based data acquisition
system. The work involves the development of Detachable
Membrane Unit (enzyme based biomembrane) with immobilized
glucose oxidase on the membrane and interfacing the same to the
signal conditioning system. The current generated by the biosensor
for different glucose concentrations was signal conditioned, then
acquired and computed by a simple AT89C51-microcontroller. The
optimum operating parameters for the better performance were found
and reported. The detailed performance evaluation of the biosensor
has been carried out. The proposed microcontroller based biosensor
system has the sensitivity of 0.04V/g/dl, with a resolution of
50mg/dl. It has exhibited very good inter day stability observed up to
30 days. Comparing to the reference method such as HPLC, the
accuracy of the proposed biosensor system is well within ± 1.5%.
The system can be used for real time analysis of glucose
concentration in the field such as, food and fermentation and clinical
(In-Vitro) applications.
Abstract: It is necessary to incorporate technological advances
achieved in the field of engineering into dentistry in order to enhance
the process of diagnosis, treatment planning and enable the doctors to
render better treatment to their patients. To achieve this ultimate goal
long distance collaborations are often necessary. This paper discusses
the various collaborative tools and their applications to solve a few
burning problems confronted by the dentists. Customization is often
the solution to most of the problems. But rapid designing,
development and cost effective manufacturing is a difficult task to
achieve. This problem can be solved using the technique of digital
manufacturing. Cases from 6 major branches of dentistry have been
discussed and possible solutions with the help of state of art
technology using rapid digital manufacturing have been proposed in
the present paper. The paper also entails the usage of existing tools in
collaborative and digital manufacturing area.
Abstract: Bacillus subtilis strain LB5 produced lipopeptide
antibiotic iturin A-2 in liquid medium. Crude extract
from cell-free supernatant of B. subtilis cultivated broth extracted
with n-butanol showed antifungal activity to conidial germination of
Colletotrichum gloeosporioides. The germination of conidia was
completely inhibited by crude extract. The ultrastructure of conidia
after treated with crude extract was found an accumulation of vesiclelike
material between cell wall and plasma membrane while this
accumulation was not observed in untreated and germinated conidia.
Besides, the cell wall was not affected by crude extract.
Abstract: This study carried out to determine the effect of plant
densities on some agronomic characteristics of four safflower cultivars in spring planting. The experiment was conducted at Yazd,
Iran- using a factorial in a randomized complete block design with four replications. Cultivars were including Arak, IL, Asteria and Local and plant densities were 10, 13.3, 20 and 40 plant/m2. Number
of seeds/head, number of heads/plant, HI, 1000-seed weight and seed yield significantly decreased as planting density increased. With increasing planting density, LAI, plant height, first branch height and
biological yield increased. The highest seed yield was obtained in 13.3 plant/m2 (2167 kg/ha). There were significant differences
between cultivars. Local cv. had higher seed yield than the other cultivars mainly due to higher heads/plant and seeds/head.
Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.
Abstract: Rice bran has been abandoned as agricultural waste for million tonnes per year in Thailand, therefore they have been proposed to be utilized as a rich carbon source in the production of bioethanol. Many toxic compounds are possibly released during the pretreatment of rice bran prior the fermentation process. This study aims to analyze on the availability of toxic compounds and the amount of glucose obtained from 2 different pretreatments using sulfuric acid and mixed cellulase enzymes (without and with delignification/ activated charcoal). The concentration of furfural, 5- hydroxymethyl furfural (5-HMF), levulinic acid, vanillin, syringaldehyde and4-hydroxybenzaldehyde (4-HB) and the percent acetic acid were found to be 0.0517 ± 0.049 mg/L, 0.032 ± 0.06 mg/L, 21074 ± 1685.62 mg/L, 126.265 ± 6.005 mg/L, 2.89 ± 0.30 mg/L, 0.37 ± 0.031mg/L and 0.72% under the pretreatment process without delignification/ activated charcoal treatment and 384.47 ± 99.02 g/L, 0.068 mg/L, 142107.62 ± 8664.6 mg/L, 0.19 mg/L, 5.43 ± 3.29 mg/L, 4.80 ± 0.76 mg/L and 0.254% under the pretreatment process with delignification/ activated charcoal treatment respectively. The presence of high concentration of acetic acid was found to impede the growth of Zymomonas mobilis strain TISTR 551 despite the present of high concentration of levulinic acid. Z. mobilis strain TISTR 551 was found to produce 8.96 ± 4.06 g/L of ethanol under 4 days fementation period in biofilm stage in which represented 40% theoretical yield.
Abstract: We created the tool, which combines the powerful
GENESIS (GEneral NEural SImulation System) simulation language
with the up-to-date visualisation and internet techniques. Our
solution resides in the connection between the simulation output from
GENESIS, which is converted to the data-structure suitable for
WWW browsers and VRML (Virtual Reality Modelling Language)
viewers. The selected GENESIS simulations are once exported into
the VRML code, and stored in our neurovisualisation portal
(webserver). There, the loaded models, demonstrating mainly the
spread of electrical signal (action potentials, postsynaptic potentials)
along the neuronal membrane (axon, dendritic tree, neuron) could be
displayed in the client-s VRML viewer, without interacting with
original GENESIS environment. This enables the visualisation of
basic neurophysiological phenomena designed for GENESIS
simulator on the independent OS (operation system).
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: A new supported liquid membrane (SLM) system for
the selective transport of VO2
+ ions was prepared in this present
work. The SLM was a thin porous polyvinylidene difluoride
(PVDF) membrane soaked with Di-(2-ethylhexyl) phosphoric acid
(D2EHPA) as mobile carrier in Xylene as organic solvent.
D2EHPA acts as a highly selective carrier for the uphill transport of
VO2
+ ions through the SLM. The transport of VO2
+ ions reached to
64%. In the presence of P2O7-2 ion as suitable masking agent in the
feed solution, the interfering effects of other cations were eliminated.
Abstract: Supercritical carbon dioxide (SC-CO2) was used as a
solvent to extract oil from wheat bran. Extractions were carried out in a
semi-batch process at temperatures ranging from 40 to 60ºC and
pressures ranging from 10 to 30 MPa, with a carbon dioxide (CO2)
flow rate of 26.81 g/min. The oil obtained from wheat bran at different
extraction conditions was quantitatively measured to investigate the
solubility of oil in SC-CO2. The solubility of wheat bran oil was found
to be enhanced in high temperature and pressure. The composition of
fatty acids in wheat bran oil was measured by gas chromatography
(GC). Linoleic, palmitic, oleic and γ-linolenic acid were the major
fatty acids of wheat bran oil. Tocopherol contents in oil were analyzed
by high performance liquid chromatography (HPLC). The highest
amount of phenolics and tocopherols (α and β) were found at
temperature of 60ºC and pressure of 30 MPa.
Abstract: This paper details few mechanical modeling and
design issues of RF MEMS switches. We concentrate on an
electrostatically actuated broad side series switch; surface
micromachined with a crab leg membrane. The same results are
extended to any complex structure. With available experimental data
and fabrication results, we present the variation in dynamic
performance and compliance of the switch with reference to few
design issues, which we find are critical in deciding the dynamic
behavior of the switch, without compromise on the RF
characteristics. The optimization of pull in voltage, transient time and
resonant frequency with regard to these critical design parameters are
also presented.