Abstract: A fuzzy predictive pursuit guidance is proposed as an
alternative to the conventional methods. The purpose of this scheme
is to obtain a stable and fast guidance. The noise effects must be
reduced in homing missile guidance to get an accurate control. An
aerodynamic missile model is simulated first and a fuzzy predictive
pursuit control algorithm is applied to reduce the noise effects. The
performance of this algorithm is compared with the performance of
the classical proportional derivative control. Stability analysis of the
proposed guidance method is performed and compared with the
stability properties of other guidance methods. Simulation results
show that the proposed method provides the satisfying performance.
Abstract: ELS is an important ground based hardware in the
loop simulator used for aerodynamics torque loading experiments
of the actuators under test. This work focuses on improvement of the
transient response of torque controller with parameters uncertainty
of Electrical Load Simulator (ELS).The parameters of load simulator
are estimated online and the model is updated, eliminating the model
error and improving the steady state torque tracking response of
torque controller. To improve the Transient control performance the
gain of robust term of SMC is updated online using fuzzy logic
system based on the amount of uncertainty in parameters of load
simulator. The states of load simulator which cannot be measured
directly are estimated using luenberger observer with update of new
estimated parameters. The stability of the control scheme is verified
using Lyapunov theorem. The validity of proposed control scheme is
verified using simulations.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: This paper presents a CFD analysis of the flow field
around a thin flat plate of infinite span inclined at 90° to a fluid
stream of infinite extent. Numerical predictions have been compared
to experimental measurements, in order to assess the potential of the
finite volume code of determining the aerodynamic forces acting on a
bluff body invested by a fluid stream of infinite extent.
Several turbulence models and spatial node distributions have
been tested. Flow field characteristics in the neighborhood of the flat
plate have been investigated, allowing the development of a
preliminary procedure to be used as guidance in selecting the
appropriate grid configuration and the corresponding turbulence
model for the prediction of the flow field over a two-dimensional
vertical flat plate.
Abstract: This paper present a new way to find the aerodynamic
characteristic equation of missile for the numerical trajectories
prediction more accurate. The goal is to obtain the polynomial
equation based on two missile characteristic parameters, angle of
attack (α ) and flight speed (ν ). First, the understudied missile is
modeled and used for flow computational model to compute
aerodynamic force and moment. Assume that performance range of
understudied missile where range -10< α
Abstract: A full six degrees of freedom (6-DOF) flight dynamics
model is proposed for the accurate prediction of short and long-range
trajectories of high spin and fin-stabilized projectiles via atmospheric
flight to final impact point. The projectiles is assumed to be both rigid
(non-flexible), and rotationally symmetric about its spin axis launched
at low and high pitch angles. The mathematical model is based on the
full equations of motion set up in the no-roll body reference frame and
is integrated numerically from given initial conditions at the firing
site. The projectiles maneuvering motion depends on the most
significant force and moment variations, in addition to wind and
gravity. The computational flight analysis takes into consideration the
Mach number and total angle of attack effects by means of the
variable aerodynamic coefficients. For the purposes of the present
work, linear interpolation has been applied from the tabulated database
of McCoy-s book. The developed computational method gives
satisfactory agreement with published data of verified experiments and
computational codes on atmospheric projectile trajectory analysis for
various initial firing flight conditions.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.
Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: This paper investigates the aerodynamic characters of a model ducted fan system, analyses the basic principle of the effect of thrust promotion and torque reduction, discovers the relationship between the revolutions per minute(RPM) of the fan and the characters of thrust, as well as system torque. Firstly a model ducted fan has been designed and manufactured according to the specific structure of flow field, then CFD simulation has been carried out to analyze such aerodynamics, finally bench tests have been used to validate the simulation results and system configuration.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: The present work describes a computational study of
aerodynamic characteristics of GLC305 airfoil clean and with 16.7
min ice shape (rime 212) and 22.5 min ice shape (glaze 944).The
performance of turbulence models SA, Kε, Kω Std, and Kω SST
model are observed against experimental flow fields at different
Mach numbers 0.12, 0.21, 0.28 in a range of Reynolds numbers
3x106, 6x106, and 10.5x106 on clean and iced aircraft airfoil
GLC305. Numerical predictions include lift, drag and pitching
moment coefficients at different Mach numbers and at different angle
of attacks were done. Accuracy of solutions with respect to the
effects of turbulence models, variation of Mach number, initial
conditions, grid resolution and grid spacing near the wall made the
study much sensitive. Navier Stokes equation based computational
technique is used. Results are very close to the experimental results.
It has seen that SA and SST models are more efficient than Kε and
Kω standard in under study problem.
Abstract: The methodology of numerical simulation and calculation of aerodynamic characteristics of aircraft taking into account impact of wake on it has been developed. The results of numerical experiment in comparison with the data obtained in the wind tunnel are presented. Efficiency of methodology of calculation and the reliability of the results is shown.
Abstract: This article discusses stress analysis and the shape characteristics of the inflatable wing, and then introduces the design method of inflatable wing, in order to accurately approximate a standard airfoil. It specifically analyses the aerodynamic characteristics of the inflatable wing with the method of CFD, along with comparing to standard airfoil, afterwards we carries out the manufacture of inflatable wing and the flight test.