Abstract: This paper deals about four items assembly process of
linear drive. This assembly will be realized in flexible assembly cell
on Institute of Manufacturing Systems and Applied Mechanics. There
is defined manufacturing cell, individual actuators created our
flexible cell. Next chapter is about control type, detailed describe a
sequence control type, which will be used in mentioned flexible
assembly cell. All cell control is divided in individual steps
instructions. There instructions illustrate table number III.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: This paper will provide the kinematic and dynamic
analysis of a lower limb exoskeleton. The forward and inverse
kinematics of proposed exoskeleton is performed using Denevit and
Hartenberg method. The torques required for the actuators will be
calculated using Lagrangian formulation technique. This research can
be used to design the control of the proposed exoskeleton.
Abstract: This paper presents the vibrations suppression of a thermoelastic beam subject to sudden heat input by a distributed piezoelectric actuators. An optimization problem is formulated as the minimization of a quadratic functional in terms of displacement and velocity at a given time and with the least control effort. The solution method is based on a combination of modal expansion and variational approaches. The modal expansion approach is used to convert the optimal control of distributed parameter system into the optimal control of lumped parameter system. By utilizing the variational approach, an explicit optimal control law is derived and the determination of the corresponding displacement and velocity is reduced to solving a set of ordinary differential equations.
Abstract: The psychological and physical trauma associated with the loss of a human limb can severely impact on the quality of life of an amputee rendering even the most basic of tasks very difficult. A prosthetic device can be of great benefit to the amputee in the performance of everyday human tasks. This paper outlines a proposed mechanical design of a 12 degree-of-freedom SMA actuated artificial hand. It is proposed that the SMA wires be embedded intrinsically within the hand structure which will allow for significant flexibility for use either as a prosthetic hand solution, or as part of a complete lower arm prosthetic solution. A modular approach is taken in the design facilitating ease of manufacture and assembly, and more importantly, also allows the end user to easily replace SMA wires in the event of failure. A biomimetric approach has been taken during the design process meaning that the artificial hand should replicate that of a human hand as far as is possible with due regard to functional requirements. The proposed design has been exposed to appropriate loading through the use of finite element analysis (FEA) to ensure that it is structurally sound. Theoretical analysis of the mechanical framework was also carried out to establish the limits of the angular displacement and velocity of the finger tip as well finger tip force generation. A combination of various polymers and Titanium, which are suitably lightweight, are proposed for the manufacture of the design.
Abstract: In this paper we intend to ascertain the state of the art on multifingered end-effectors, also known as robotic hands or dexterous robot hands, and propose an experimental setup for an innovative task based design approach, involving cutting edge technologies in motion capture. After an initial description of the capabilities and complexity of a human hand when grasping objects, in order to point out the importance of replicating it, we analyze the mechanical and kinematical structure of some important works carried out all around the world in the last three decades and also review the actuators and sensing technologies used. Finally we describe a new design philosophy proposing an experimental setup for the first stage using recent developments in human body motion capture systems that might lead to lighter and always more dexterous robotic hands.
Abstract: This paper features the proposed modeling and design
of a Robust Decentralized Periodic Output Feedback (RDPOF)
control technique for the active vibration control of smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminum beam, thus giving rise to
a multimodel of the smart structure system. Using model order
reduction technique, the reduced order model of the higher order
system is obtained based on dominant eigen value retention and the
method of Davison. RDPOF controllers are designed for the above 5
multivariable-multimodel plant. The closed loop responses with the
RDPOF feedback gain and the magnitudes of the control input are
observed and the performance of the proposed multimodel smart
structure system with the controller is evaluated for vibration control.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: Shape memory alloy (SMA) actuators have found a
wide range of applications due to their unique properties such as high
force, small size, lightweight and silent operation. This paper presents
the development of compact (SMA) actuator and cooling system in
one unit. This actuator is developed for multi-fingered hand. It
consists of nickel-titanium (Nitinol) SMA wires in compact forming.
The new arrangement insulates SMA wires from the human body by
housing it in a heat sink and uses a thermoelectric device for rejecting
heat to improve the actuator performance. The study uses
optimization methods for selecting the SMA wires geometrical
parameters and the material of a heat sink. The experimental work
implements the actuator prototype and measures its response.
Abstract: Evolvable Hardware (EHW) has been regarded as adaptive system acquired by wide application market. Consumer market of any good requires diversity to satisfy consumers- preferences. Adaptation of EHW is a key technology that could provide individual approach to every particular user. This situation raises a question: how to set target for evolutionary algorithm? The existing techniques do not allow consumer to influence evolutionary process. Only designer at the moment is capable to influence the evolution. The proposed consumer-triggered evolution overcomes this problem by introducing new features to EHW that help adaptive system to obtain targets during consumer stage. Classification of EHW is given according to responsiveness, imitation of human behavior and target circuit response. Home intelligent water heating system is considered as an example.
Abstract: Small satellites have become increasingly popular recently as a means of providing educational institutes with the chance to design, construct, and test their spacecraft from beginning to the possible launch due to the low launching cost. This approach is remarkably cost saving because of the weight and size reduction of such satellites. Weight reduction could be realised by utilising electromagnetic coils solely, instead of different types of actuators. This paper describes the restrictions of using only “Electromagnetic" actuation for 3D stabilisation and how to make the magnetorquer based attitude control feasible using Fuzzy Logic Control (FLC). The design is developed to stabilize the spacecraft against gravity gradient disturbances with a three-axis stabilizing capability.
Abstract: this paper presents a novel neural network controller
with composite adaptation low to improve the trajectory tracking
problems of biped robots comparing with classical controller. The
biped model has 5_link and 6 degrees of freedom and actuated by
Plated Pneumatic Artificial Muscle, which have a very high power to
weight ratio and it has large stoke compared to similar actuators. The
proposed controller employ a stable neural network in to approximate
unknown nonlinear functions in the robot dynamics, thereby
overcoming some limitation of conventional controllers such as PD
or adaptive controllers and guarantee good performance. This NN
controller significantly improve the accuracy requirements by
retraining the basic PD/PID loop, but adding an inner adaptive loop
that allows the controller to learn unknown parameters such as
friction coefficient, therefore improving tracking accuracy.
Simulation results plus graphical simulation in virtual reality show
that NN controller tracking performance is considerably better than
PD controller tracking performance.
Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.
Abstract: Comparison of two approaches for the simulation of
the dynamic behaviour of a permanent magnet linear actuator is
presented. These are full coupled model, where the electromagnetic
field, electric circuit and mechanical motion problems are solved
simultaneously, and decoupled model, where first a set of static
magnetic filed analysis is carried out and then the electric circuit and
mechanical motion equations are solved employing bi-cubic spline
approximations of the field analysis results. The results show that the
proposed decoupled model is of satisfactory accuracy and gives more
flexibility when the actuator response is required to be estimated for
different external conditions, e.g. external circuit parameters or
mechanical loads.
Abstract: ELS is an important ground based hardware in the
loop simulator used for aerodynamics torque loading experiments
of the actuators under test. This work focuses on improvement of the
transient response of torque controller with parameters uncertainty
of Electrical Load Simulator (ELS).The parameters of load simulator
are estimated online and the model is updated, eliminating the model
error and improving the steady state torque tracking response of
torque controller. To improve the Transient control performance the
gain of robust term of SMC is updated online using fuzzy logic
system based on the amount of uncertainty in parameters of load
simulator. The states of load simulator which cannot be measured
directly are estimated using luenberger observer with update of new
estimated parameters. The stability of the control scheme is verified
using Lyapunov theorem. The validity of proposed control scheme is
verified using simulations.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.