Abstract: An experiment was conducted on the comparative
study of drip and furrow irrigation methods at the farmer-s field in
Umar Kot. The total area under experiment about 4000m2 was
divided into two equal portions. One portion about 40m X 50m was
occupied by drip and the other portion about 40m X 50m by furrow
irrigation method. Soil at the experimental site was clay loam in
texture for 0-60cm depth; average dry bulk density and field capacity
was 1.16g/cm3 and 28.5% respectively. The results reveal that the
drip irrigation method saved 56.4% water and gave 22% more yield
as compared to that of furrow irrigation method. Higher water use
efficiency about 4.87 was obtained in drip irrigation method; whereas
lower water used efficiency about 1.66 was obtained in furrow
irrigation method. The present study suggests farming community to
adopt drip irrigation method instead of old traditional flooding
methods.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: In this paper, a fast motion compensation algorithm is
proposed that improves coding efficiency for video sequences with
brightness variations. We also propose a cross entropy measure
between histograms of two frames to detect brightness variations. The
framewise brightness variation parameters, a multiplier and an offset
field for image intensity, are estimated and compensated. Simulation
results show that the proposed method yields a higher peak signal to
noise ratio (PSNR) compared with the conventional method, with a
greatly reduced computational load, when the video scene contains
illumination changes.
Abstract: In this paper, a recursive algorithm for the
computation of 2-D DCT using Ramanujan Numbers is proposed.
With this algorithm, the floating-point multiplication is completely
eliminated and hence the multiplierless algorithm can be
implemented using shifts and additions only. The orthogonality of
the recursive kernel is well maintained through matrix factorization
to reduce the computational complexity. The inherent parallel
structure yields simpler programming and hardware implementation
and provides
log 1
2
3
2 N N-N+
additions and
N N
2 log
2 shifts which is
very much less complex when compared to other recent multiplierless
algorithms.
Abstract: Insect pests are the major source of crop
damage, yield and quality reduction in Pakistan and else
where in the world. Cotton crop is the most hit crop in
Pakistan followed by rice and the second most important
foreign exchange earning crop. A wide variety of staple,
horticultural and cash crops grown, reflect serious problems of
many types of insect pests. To overcome the insect pest
problem, pesticide use in Pakistan has increased substantially
which has now been further intensified. Pesticides worth more
than billions of rupees are imported every year. This paper
reviews the over all pesticide use in Pakistan in relation to
pesticide prices, support price of cotton and rice, pesticide use
in different provinces of Pakistan on different crops and their
impact on crop productivity. The environmental pollution
caused by the use of pesticides, contamination of soil and
water resources and the danger associated with the disposal of
their empty containers is also discussed in detail.
Abstract: In general the images used for compression are of
different types like dark image, high intensity image etc. When these
images are compressed using Counter Propagation Neural Network,
it takes longer time to converge. The reason for this is that the given
image may contain a number of distinct gray levels with narrow
difference with their neighborhood pixels. If the gray levels of the
pixels in an image and their neighbors are mapped in such a way that
the difference in the gray levels of the neighbor with the pixel is
minimum, then compression ratio as well as the convergence of the
network can be improved. To achieve this, a Cumulative Distribution
Function is estimated for the image and it is used to map the image
pixels. When the mapped image pixels are used the Counter
Propagation Neural Network yield high compression ratio as well as
it converges quickly.
Abstract: Magnesium wastes and scraps, one of the metal wastes, are produced by many industrial activities, all over the world. Their growing size is becoming a future problem for the world. In this study, the use of magnesium wastes as a raw material in the production of the magnesium borate hydrates are aimed. The method used in the experiments is hydrothermal synthesis. The conditions are set to, waste magnesium to B2O3, 1:3 as a molar ratio. Four different reaction times are studied which are 30, 60, 120 and 240 minutes. For the identification analyses X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR) and Raman spectroscopy techniques are used. As a result at all the reaction times magnesium borate hydrates are synthesized and the most crystalline forms are obtained at a reaction time of 120 minutes. The overall yields of the production are found between the values of 65-80 %.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: The tray/multi-tray distillation process is a topic that
has been investigated to great detail over the last decade by many
teams such as Jubran et al. [1], Adhikari et al. [2], Mowla et al. [3],
Shatat et al. [4] and Fath [5] to name a few. A significant amount of
work and effort was spent focusing on modeling and/simulation of
specific distillation hardware designs. In this work, we have focused
our efforts on investigating and gathering experimental data on
several engineering and design variables to quantify their influence
on the yield of the multi-tray distillation process. Our goals are to
generate experimental performance data to bridge some existing gaps
in the design, engineering, optimization and theoretical modeling
aspects of the multi-tray distillation process.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: Recent progress in calculation of the one-loop selfenergy
of the electron bound in the Coulomb field is summarized.
The relativistic multipole expansion is introduced. This expansion
is based on a single assumption: except for the part of the time
component of the electron four-momentum corresponding to the
electron rest mass, the exchange of four-momentum between the
virtual electron and photon can be treated perturbatively. For non Sstates
and normalized difference n3En −E1 of the S-states this
itself yields very accurate results after taking the method to the third
order. For the ground state the perturbation treatment of the electron
virtual states with very high three-momentum is to be avoided. For
these states one can always rearrange the pertinent expression in such
a way that free-particle approximation is allowed. Combination of
the relativistic multipole expansion and free-particle approximation
yields very accurate result after taking the method to the ninth order.
These results are in very good agreement with the previous results
obtained by the partial wave expansion and definitely exclude the
possibility that the uncertainity in determination of the proton radius
comes from the uncertainity in the calculation of the one-loop selfenergy.
Abstract: This paper presents the determination of the proper
quality costs parameters which provide the optimum return. The
system dynamics simulation was applied. The simulation model was
constructed by the real data from a case of the electronic devices
manufacturer in Thailand. The Steepest Descent algorithm was
employed to optimise. The experimental results show that the
company should spend on prevention and appraisal activities for 850
and 10 Baht/day respectively. It provides minimum cumulative total
quality cost, which is 258,000 Baht in twelve months. The effect of
the step size in the stage of improving the variables to the optimum
was also investigated. It can be stated that the smaller step size
provided a better result with more experimental runs. However, the
different yield in this case is not significant in practice. Therefore, the
greater step size is recommended because the region of optima could
be reached more easily and rapidly.
Abstract: This study carried out to determine the effect of plant
densities on some agronomic characteristics of four safflower cultivars in spring planting. The experiment was conducted at Yazd,
Iran- using a factorial in a randomized complete block design with four replications. Cultivars were including Arak, IL, Asteria and Local and plant densities were 10, 13.3, 20 and 40 plant/m2. Number
of seeds/head, number of heads/plant, HI, 1000-seed weight and seed yield significantly decreased as planting density increased. With increasing planting density, LAI, plant height, first branch height and
biological yield increased. The highest seed yield was obtained in 13.3 plant/m2 (2167 kg/ha). There were significant differences
between cultivars. Local cv. had higher seed yield than the other cultivars mainly due to higher heads/plant and seeds/head.
Abstract: Hydrogen is regarded to play an important role in
future energy systems because it can be produced from abundant
resources and its combustion only generates water. The disposal of
waste tyres is a major problem in environmental management
throughout the world. The use of waste materials as a source of
hydrogen is particularly of interest in that it would also solve a waste
treatment problem. There is much interest in the use of alternative
feedstocks for the production of hydrogen since more than 95% of
current production is from fossil fuels. The pyrolysis of waste tyres
for the production of liquid fuels, activated carbons and gases has
been extensively researched. However, combining pyrolysis with
gasification is a novel process that can gasify the gaseous products
from pyrolysis. In this paper, an experimental investigation into the
production of hydrogen and other gases from the bench scale
pyrolysis-gasification of tyres has been investigated. Experiments
were carried using a two stage system consisting of pyrolysis of the
waste tyres followed by catalytic steam gasification of the evolved
gases and vapours in a second reactor. Experiments were conducted
at a pyrolysis temperature of 500 °C using Ni/Al2O3 as a catalyst. The
results showed that there was a dramatic increase in gas yield and the
potential H2 production when the gasification temperature was
increased from 600 to 900 oC. Overall, the process showed that high
yields of hydrogen can be produced from waste tyres.
Abstract: The deterministic quantum transfer-matrix (QTM)
technique and its mathematical background are presented. This
important tool in computational physics can be applied to a class of
the real physical low-dimensional magnetic systems described by the
Heisenberg hamiltonian which includes the macroscopic molecularbased
spin chains, small size magnetic clusters embedded in some
supramolecules and other interesting compounds. Using QTM, the
spin degrees of freedom are accurately taken into account, yielding
the thermodynamical functions at finite temperatures.
In order to test the application for the susceptibility calculations to
run in the parallel environment, the speed-up and efficiency of
parallelization are analyzed on our platform SGI Origin 3800 with
p = 128 processor units. Using Message Parallel Interface (MPI)
system libraries we find the efficiency of the code of 94% for
p = 128 that makes our application highly scalable.
Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.