Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: The proposed multiplexer-based novel 1-bit full
adder cell is schematized by using DSCH2 and its layout is generated
by using microwind VLSI CAD tool. The adder cell layout
interconnect analysis is performed by using BSIM4 layout analyzer.
The adder circuit is compared with other six existing adder circuits
for parametric analysis. The proposed adder cell gives better
performance than the other existing six adder circuits in terms of
power, propagation delay and PDP. The proposed adder circuit is
further analyzed for interconnect analysis, which gives better
performance than other adder circuits in terms of layout thickness,
width and height.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: This paper proposes an active soft-switching circuit for
bridge converters aiming to improve the power conversion efficiency.
The proposed circuit achieves loss-less switching for both main and
auxiliary switches without increasing the main switch current/voltage
rating. A winding coupled to the primary of power transformer
ensures ZCS for the auxiliary switches during their turn-off. A 350 W,
100 kHz phase shifted full bridge (PSFB) converter is built to validate
the analysis and design. Theoretical loss calculations for proposed
circuit is presented. The proposed circuit is compared with passive
soft switched PSFB in terms of efficiency and loss in duty cycle.
Abstract: The paper examines the performance of bit-interleaved parity (BIP) methods in error rate monitoring, and in declaration and clearing of alarms in those transport networks that employ automatic protection switching (APS). The BIP-based error rate monitoring is attractive for its simplicity and ease of implementation. The BIP-based results are compared with exact results and are found to declare the alarms too late, and to clear the alarms too early. It is concluded that the standards development and systems implementation should take into account the fact of early clearing and late declaration of alarms. The window parameters defining the detection and clearing thresholds should be set so as to build sufficient hysteresis into the system to ensure that BIP-based implementations yield acceptable performance results.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: The connection between solar activity and adverse phenomena in the Earth’s environment that can affect space and ground based technologies has spurred interest in Space Weather (SW) research. A great effort has been put on the development of suitable models that can provide advanced forecast of SW events. With the progress in computational technology, it is becoming possible to develop operational large scale physics based models which can incorporate the most important physical processes and domains of the Sun-Earth system. In order to enhance our SW prediction capabilities we are developing advanced numerical tools. With operational requirements in mind, our goal is to develop a modular simulation framework of propagation of the disturbances from the Sun through interplanetary space to the Earth. Here, we report and discuss on the development of coronal field and solar wind components for a large scale MHD code. The model for these components is based on a potential field source surface model and an empirical Wang-Sheeley-Arge solar wind relation.
Abstract: An image texture analysis and target recognition approach of using an improved image texture feature coding method (TFCM) and Support Vector Machine (SVM) for target detection is presented. With our proposed target detection framework, targets of interest can be detected accurately. Cascade-Sliding-Window technique was also developed for automated target localization. Application to mammogram showed that over 88% of normal mammograms and 80% of abnormal mammograms can be correctly identified. The approach was also successfully applied to Synthetic Aperture Radar (SAR) and Ground Penetrating Radar (GPR) images for target detection.
Abstract: We present a general comparison of punctual kriging based image restoration for different neighbourhood sizes. The formulation of the technique under consideration is based on punctual kriging and fuzzy concepts for image restoration in spatial domain. Three different neighbourhood windows are considered to estimate the semivariance at different lags for studying its effect in reduction of negative weights resulted in punctual kriging, consequently restoration of degraded images. Our results show that effect of neighbourhood size higher than 5x5 on reduction in negative weights is insignificant. In addition, image quality measures, such as structure similarity indices, peak signal to noise ratios and the new variogram based quality measures; show that 3x3 window size gives better performance as compared with larger window sizes.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: The client server systems using mobile
communications networks for data transmission became very
attractive for many economic agents, in the purpose of promoting and
offering electronic services to their clients. E-services are suitable for
business developing and financial benefits increasing. The products
or services can be efficiently delivered to a large number of clients,
using mobile Internet access technologies. The clients can have
access to e-services, anywhere and anytime, with the support of 3G,
GPRS, WLAN, etc., channels bandwidth, data services and protocols.
Based on the mobile communications networks evolution and
development, a convergence of technological and financial interests
of mobile operators, software developers, mobile terminals producers
and e-content providers is established. These will lead to a high level
of integration of IT&C resources and will facilitate the value added
services delivery through the mobile communications networks. In
this paper it is presented a client server system, for e-services access,
with Smartphones and PDA-s mobile software applications, installed
on Symbian and Windows Mobile operating systems.
Abstract: Noise contamination in a magnetic resonance (MR)
image could occur during acquisition, storage, and transmission in
which effective filtering is required to avoid repeating the MR
procedure. In this paper, an iterative asymmetrical triangle fuzzy
filter with moving average center (ATMAVi filter) is used to reduce
different levels of salt and pepper noise in a brain MR image. Besides
visual inspection on filtered images, the mean squared error (MSE) is
used as an objective measurement. When compared with the median
filter, simulation results indicate that the ATMAVi filter is effective
especially for filtering a higher level noise (such as noise density =
0.45) using a smaller window size (such as 3x3) when operated
iteratively or using a larger window size (such as 5x5) when operated
non-iteratively.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: The Automatic Speech Recognition (ASR) applied to
Arabic language is a challenging task. This is mainly related to the
language specificities which make the researchers facing multiple
difficulties such as the insufficient linguistic resources and the very
limited number of available transcribed Arabic speech corpora. In
this paper, we are interested in the development of a HMM-based
ASR system for Standard Arabic (SA) language. Our fundamental
research goal is to select the most appropriate acoustic parameters
describing each audio frame, acoustic models and speech recognition
unit. To achieve this purpose, we analyze the effect of varying frame
windowing (size and period), acoustic parameter number resulting
from features extraction methods traditionally used in ASR, speech
recognition unit, Gaussian number per HMM state and number of
embedded re-estimations of the Baum-Welch Algorithm. To evaluate
the proposed ASR system, a multi-speaker SA connected-digits
corpus is collected, transcribed and used throughout all experiments.
A further evaluation is conducted on a speaker-independent continue
SA speech corpus. The phonemes recognition rate is 94.02% which is
relatively high when comparing it with another ASR system
evaluated on the same corpus.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: Due to the increasing penetration of wind energy, it is
necessary to possess design tools that are able to simulate the impact
of these installations in utility grids. In order to provide a net
contribution to this issue a detailed wind park model has been
developed and is briefly presented. However, the computational costs
associated with the performance of such a detailed model in
describing the behavior of a wind park composed by a considerable
number of units may render its practical application very difficult. To
overcome this problem integral manifolds theory has been applied to
reduce the order of the detailed wind park model, and therefore
create the conditions for the development of a dynamic equivalent
which is able to retain the relevant dynamics with respect to the
existing a.c. system. In this paper integral manifold method has been
introduced for order reduction. Simulation results of the proposed
method represents that integral manifold method results fit the
detailed model results with a higher precision than singular
perturbation method.
Abstract: Real-time embedded systems should benefit from
component-based software engineering to handle complexity and
deal with dependability. In these systems, applications should not
only be logically correct but also behave within time windows.
However, in the current component based software engineering
approaches, a few of component models handles time properties in
a manner that allows efficient analysis and checking at the
architectural level. In this paper, we present a meta-model for
component-based software description that integrates timing
issues. To achieve a complete functional model of software
components, our meta-model focuses on four functional aspects:
interface, static behavior, dynamic behavior, and interaction
protocol. With each aspect we have explicitly associated a time
model. Such a time model can be used to check a component-s
design against certain properties and to compute the timing
properties of component assemblies.
Abstract: Advances in computing applications in recent years
have prompted the demand for more flexible scheduling models for
QoS demand. Moreover, in practical applications, partly violated
temporal constraints can be tolerated if the violation meets certain
distribution. So we need extend the traditional Liu and Lanland model
to adapt to these circumstances. There are two extensions, which are
the (m, k)-firm model and Window-Constrained model. This paper
researches on weakly hard real-time constraints and their combination
to support QoS. The fact that a practical application can tolerate some
violations of temporal constraint under certain distribution is
employed to support adaptive QoS on the open real-time system. The
experiment results show these approaches are effective compared to
traditional scheduling algorithms.