Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: To simulate expected climate change, we implemented a two-factor (temperature and soil moisture) field design in a forest in Ontario, Canada. To manipulate moisture input, we erected rain-exclusion structures. Under each structure, plots were watered with one of three treatments and thermally controlled with three heat treatments to simulate changes in air temperature and rainfall based on the climate model (GCM) predictions for the study area. Environmental conditions (including untreated controls) were monitored tracking air temperature, soil temperature, soil moisture, and photosynthetically active radiation. We measured rainfall and relative humidity at the site outside the rain-exclusion structures. Analyses of environmental conditions demonstrates that the temperature manipulation was most effective at maintaining target temperature during the early part of the growing season, but it was more difficult to keep the warmest treatment at 5º C above ambient by late summer. Target moisture regimes were generally achieved however incoming solar radiation was slightly attenuated by the structures.
Abstract: Structural and UV/Visible optical properties can be
useful to describe a material for the CIGS solar cell active layer,
therefore, this work demonstrates the properties like surface
morphology, X-ray Photoelectron Spectroscopy (XPS) bonding
energy (EB) core level spectra, UV/Visible absorption spectra,
refractive index (n), optical energy band (Eg), reflection spectra for
the Cu25 (In16Ga9) Se40Te10 (CIGST-1) and Cu20 (In14Ga9) Se45Te12
(CIGST-2) chalcogenide compositions. Materials have been
exhibited homogenous surface morphologies, broading /-or diffusion
of bonding energy peaks relative elemental values and a high
UV/Visible absorption tendency in the wave length range 400 nm-
850 nm range with the optical energy band gaps 1.37 and 1.42
respectively. Subsequently, UV/Visible reflectivity property in the
wave length range 250 nm to 320 nm for these materials has also
been discussed.
Abstract: We have modeled the effect of a graded band gap
window on the performance of a single junction AlxGa1-xAs/GaAs
solar cell. First, we study the electrical characteristics of a single
junction AlxGa1-xAs/GaAs solar cell, by employing an optimized
structure for this solar cell, we show that grading the band gap of the
window can increase the conversion efficiency of the solar cell by
about 1.5%, and can also improve the quantum efficiency of the solar
cell especially at shorter wavelengths.
Abstract: The use of solar control film on windows as one of
solar passive strategies for building have becoming important and is
gaining recognition. Malaysia located close to equator is having
warm humid climate with long sunshine hours and abundant solar
radiation throughout the year. Hence, befitting solar control on
windows is absolutely necessary to capture the daylight whilst
moderating thermal impact and eliminating glare problems. This is
one of the energy efficient strategies to achieve thermal and visual
comfort in buildings. Therefore, this study was carried out to
investigate the effect of window solar controls on thermal and visual
performance of naturally ventilated buildings. This was conducted via
field data monitoring using a test building facility. Four types of
window glazing systems were used with three types of solar control
films. Data were analysed for thermal and visual impact with
reference to thermal and optical characteristics of the films. Results
show that for each glazing system, the surface temperature of
windows are influenced by the Solar Energy Absorption property, the
indoor air temperature are influenced by the Solar Energy
Transmittance and Solar Energy Reflectance, and the daylighting by
Visible Light Transmission and Shading Coefficient. Further
investigations are underway to determine the mathematical relation
between thermal energy and visual performance with the thermal and
optical characteristics of solar control films.
Abstract: Battery storage system is emerging as an essential component of hybrid power system based on renewable energy resources such as solar and wind in order to make these sources dispatchable. Accurate modeling of battery storage system is ssential in order to ensure optimal planning of hybrid power systems incorporating battery storage. Majority of the system planning studies involving battery storage assume battery charging efficiency to be constant. However a strong correlation exists between battery charging efficiency and battery state of charge. In this work a Fuzzy logic based model has been presented for determining battery charging efficiency relative to a particular SOC. In order to demonstrate the efficacy of proposed approach, reliability evaluation studies are carried out for a hypothetical autonomous hybrid power system located in Jaisalmer, Rajasthan, India. The impact of considering battery charging efficiency as a function of state of charge is compared against the assumption of fixed battery charging efficiency for three different configurations comprising of wind-storage, solar-storage and wind-solar-storage.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
to accomplishing the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of an
airplane has been proposed without landing gear systems in order to
reducing accidents, time consumption, and to eliminating drawbacks
by using superconducting levitation phenomenon. This invention of
an airplane with superconductive material coating, on the solar plexus
region assist to reduce weight by approximately 4% of the total takeoff
weight, and cost effective. Moreover, we conjectured that
superconductor landing system reduces ground friction, mission fuel,
total drag, take-off and landing distance.
Abstract: This paper presents Simulated Annealing based
approach to estimate solar cell model parameters. Single diode solar
cell model is used in this study to validate the proposed approach
outcomes. The developed technique is used to estimate different
model parameters such as generated photocurrent, saturation current,
series resistance, shunt resistance, and ideality factor that govern the
current-voltage relationship of a solar cell. A practical case study is
used to test and verify the consistency of accurately estimating
various parameters of single diode solar cell model. Comparative
study among different parameter estimation techniques is presented
to show the effectiveness of the developed approach.
Abstract: Solar shading designs are important for reduction of building energy consumption and improvement of indoor thermal environment. This paper carried out a number of building simulations for evaluation of the energy performance of different shading devices based on incremental costs. The results show that movable shading devices lower incremental costs by up to 50% compared with fixed ones for the same building energy efficiency for residential buildings, and wing panel shadings are much more suitable in commercial buildings than baring screen ones and overhangs for commercial buildings.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: Photovoltaic (PV) systems provides a viable means of
power generation for applications like powering residential
appliances, electrification of villages in rural areas, refrigeration and
water pumping. Photovoltaic-power generation is reliable. The
operation and maintenance costs are very low. Since Myanmar is a
land of plentiful sunshine, especially in central and southern regions
of the country, the solar energy could hopefully become the final
solution to its energy supply problem in rural area.
Abstract: This paper presents the applicability of artificial
neural networks for 24 hour ahead solar power generation forecasting
of a 20 kW photovoltaic system, the developed forecasting is suitable
for a reliable Microgrid energy management. In total four neural
networks were proposed, namely: multi-layred perceptron, radial
basis function, recurrent and a neural network ensemble consisting in
ensemble of bagged networks. Forecasting reliability of the proposed
neural networks was carried out in terms forecasting error
performance basing on statistical and graphical methods. The
experimental results showed that all the proposed networks achieved
an acceptable forecasting accuracy. In term of comparison the neural
network ensemble gives the highest precision forecasting comparing
to the conventional networks. In fact, each network of the ensemble
over-fits to some extent and leads to a diversity which enhances the
noise tolerance and the forecasting generalization performance
comparing to the conventional networks.
Abstract: The relationship between tropical cyclogenesis and solar activity is addressed in this paper, analyzing the relationship between important parameters in the evolution of tropical cyclones as the CAPE, wind shear and relative vorticity, and the Dst geomagnetic index as a parameter of solar activity. The apparent relationship between all this phenomena has a different response depending on the phase of the solar cycles.
Abstract: Solar sunspot rotation, latitudinal bands are studied based on intelligent computation methods. A combination of image fusion method with together tree decomposition is used to obtain quantitative values about the latitudes of trajectories on sun surface that sunspots rotate around them. Daily solar images taken with SOlar and Heliospheric (SOHO) satellite are fused for each month separately .The result of fused image is decomposed with Quad Tree decomposition method in order to achieve the precise information about latitudes of sunspot trajectories. Such analysis is useful for gathering information about the regions on sun surface and coordinates in space that is more expose to solar geomagnetic storms, tremendous flares and hot plasma gases permeate interplanetary space and help human to serve their technical systems. Here sunspot images in September, November and October in 2001 are used for studying the magnetic behavior of sun.
Abstract: Various solar energy technologies exist and they have
different application techniques in the generation of electrical power.
The widespread use of photovoltaic (PV) modules in such
technologies has been limited by relatively high costs and low
efficiencies. The efficiency of PV panels decreases as the operating
temperatures increase. This is due to the affect of solar intensity and
ambient temperature. In this work, Computational Fluid Dynamics
(CFD) was used to model the heat transfer from a standard PV panel
and thus determine the rate of dissipation of heat. To accurately
model the specific climatic conditions of the United Arab Emirates
(UAE), a case study of a new build green building in Dubai was
used. A finned heat pipe arrangement is proposed and analyzed to
determine the improved heat dissipation and thus improved
performance efficiency of the PV panel. A prototype of the
arrangement is built for experimental testing to validate the CFD
modeling and proof of concept.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.