Abstract: This paper aims to present the design, fabrication and test of a novel piezoelectric actuated, check-valves embedded micropump having the advantages of miniature size, light weight and low power consumption. This device is designed to pump gases and liquids with the capability of performing the self-priming and bubble-tolerant work mode by maximizing the stroke volume of the membrane as well as the compression ratio via minimization of the dead volume of the micropump chamber and channel. By experiment apparatus setup, we can get the real-time values of the flow rate of micropump, the displacement of the piezoelectric actuator and the deformation of the check valve, simultaneously. The micropump with check valve 0.4 mm in thickness obtained higher output performance under the sinusoidal waveform of 120 Vpp. The micropump achieved the maximum pumping rates of 42.2 ml/min and back pressure of 14.0 kPa at the corresponding frequency of 28 and 20 Hz. The presented micropump is able to pump gases with a pumping rate of 196 ml/min at operating frequencies of 280 Hz under the sinusoidal waveform of 120 Vpp.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: Here we have considered non uniform microstrip
leaky-wave antenna implemented on a dielectric waveguide by a
sinusoidal profile of periodic metallic grating. The non distribution of
the attenuation constant α along propagation axis, optimize the
radiating characteristics and performances of such antennas. The
method developped here is based on an integral method where the
formalism of the admittance operator is combined to a BKW
approximation. First, the effect of the modeling in the modal analysis
of complex waves is studied in detail. Then, the BKW model is used
for the dispersion analysis of the antenna of interest. According to
antenna theory, a forced continuity of the leaky-wave magnitude at
discontinuities of the non uniform structure is established. To test the
validity of our dispersion analysis, computed radiation patterns are
presented and compared in the millimeter band.
Abstract: This article deals with numerical simulation of the
floor heating convector in 3D. Numerical simulation is focused on
cooling mode of the floor heating convector. Geometrical model
represents section of the heat exchanger – two fins with the gap
between, pipes are not involved. Two types of fin are examined –
sinusoidal and angular shape with different fin spacing. Results of fin
spacing in case of constant Reynolds number are presented. For the
numerical simulation was used commercial software Ansys Fluent.
Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Abstract: Phase error in communications systems degrades error
performance. In this paper, we present a simple approximation for the
average error probability of the binary phase shift keying (BPSK) in
the presence of phase error having a uniform distribution on arbitrary
intervals. For the simple approximation, we use symmetry and
periodicity of a sinusoidal function. Approximate result for the
average error probability is derived, and the performance is verified
through comparison with simulation result.
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Abstract: The perfect operation of common Active Filters is depended on accuracy of identification system distortion. Also, using a suitable method in current injection and reactive power compensation, leads to increased filter performance. Due to this fact, this paper presents a method based on predictive current control theory in shunt active filter applications. The harmonics of the load current is identified by using o–d–q reference frame on load current and eliminating the DC part of d–q components. Then, the rest of these components deliver to predictive current controller as a Threephase reference current by using Park inverse transformation. System is modeled in discreet time domain. The proposed method has been tested using MATLAB model for a nonlinear load (with Total Harmonic Distortion=20%). The simulation results indicate that the proposed filter leads to flowing a sinusoidal current (THD=0.15%) through the source. In addition, the results show that the filter tracks the reference current accurately.
Abstract: The flexible follower response of a translating cam with
four different profiles for rise-dwell-fall-dwell (RDFD) motion is
investigated. The cycloidal displacement motion, the modified
sinusoidal acceleration motion, the modified trapezoidal acceleration
motion, and the 3-4-5 polynomial motion are employed to describe the
rise and the fall motions of the follower and the associated four kinds of
cam profiles are studied. Since the follower flexibility is considered,
the contact point of the roller and the cam is an unknown. Two
geometric constraints formulated to restrain the unknown position are
substituted into Hamilton-s principle with Lagrange multipliers.
Applying the assumed mode method, one can obtain the governing
equations of motion as non-linear differential-algebraic equations. The
equations are solved using Runge-Kutta method. Then, the responses of
the flexible follower undergoing the four different motions are
investigated in time domain and in frequency domain.
Abstract: In this article, various models of surface tension force (CSF, CSS and PCIL) for interfacial flows have been applied to dynamic case and the results were compared. We studied the Kelvin- Helmholtz instabilities, which are produced by shear at the interface between two fluids with different physical properties. The velocity inlet is defined as a sinusoidal perturbation. When gravity and surface tension are taking into account, we observe the development of the Instability for a critic value of the difference of velocity of the both fluids. The VOF Model enables to simulate Kelvin-Helmholtz Instability as dynamic case.
Abstract: Phase locked loops in 10 Gb/s and faster data links are
low phase noise devices. Characterization of their phase jitter
transfer functions is difficult because the intrinsic noise of the PLLs
is comparable to the phase noise of the reference clock signal. The
problem is solved by using a linear model to account for the intrinsic
noise. This study also introduces a novel technique for measuring the
transfer function. It involves the use of the reference clock as a
source of wideband excitation, in contrast to the commonly used
sinusoidal excitations at discrete frequencies. The data reported here
include the intrinsic noise of a PLL for 10 Gb/s links and the jitter
transfer function of a PLL for 12.8 Gb/s links. The measured transfer
function suggests that the PLL responded like a second order linear
system to a low noise reference clock.
Abstract: Horizontal wells are proven to be better producers
because they can be extended for a long distance in the pay zone.
Engineers have the technical means to forecast the well productivity
for a given horizontal length. However, experiences have shown that
the actual production rate is often significantly less than that of
forecasted. It is a difficult task, if not impossible to identify the real
reason why a horizontal well is not producing what was forecasted.
Often the source of problem lies in the drilling of horizontal section
such as permeability reduction in the pay zone due to mud invasion
or snaky well patterns created during drilling. Although drillers aim
to drill a constant inclination hole in the pay zone, the more frequent
outcome is a sinusoidal wellbore trajectory. The two factors, which
play an important role in wellbore tortuosity, are the inclination and
side force at bit. A constant inclination horizontal well can only be
drilled if the bit face is maintained perpendicular to longitudinal axis
of bottom hole assembly (BHA) while keeping the side force nil at
the bit. This approach assumes that there exists no formation force at
bit. Hence, an appropriate BHA can be designed if bit side force and
bit tilt are determined accurately. The Artificial Neural Network
(ANN) is superior to existing analytical techniques. In this study, the
neural networks have been employed as a general approximation tool
for estimation of the bit side forces. A number of samples are
analyzed with ANN for parameters of bit side force and the results
are compared with exact analysis. Back Propagation Neural network
(BPN) is used to approximation of bit side forces. Resultant low
relative error value of the test indicates the usability of the BPN in
this area.
Abstract: This paper presents a rule-based text- to- speech
(TTS) Synthesis System for Standard Malay, namely SMaTTS. The
proposed system using sinusoidal method and some pre- recorded
wave files in generating speech for the system. The use of phone
database significantly decreases the amount of computer memory
space used, thus making the system very light and embeddable. The
overall system was comprised of two phases the Natural Language
Processing (NLP) that consisted of the high-level processing of text
analysis, phonetic analysis, text normalization and morphophonemic
module. The module was designed specially for SM to overcome
few problems in defining the rules for SM orthography system before
it can be passed to the DSP module. The second phase is the Digital
Signal Processing (DSP) which operated on the low-level process of
the speech waveform generation. A developed an intelligible and
adequately natural sounding formant-based speech synthesis system
with a light and user-friendly Graphical User Interface (GUI) is
introduced. A Standard Malay Language (SM) phoneme set and an
inclusive set of phone database have been constructed carefully for
this phone-based speech synthesizer. By applying the generative
phonology, a comprehensive letter-to-sound (LTS) rules and a
pronunciation lexicon have been invented for SMaTTS. As for the
evaluation tests, a set of Diagnostic Rhyme Test (DRT) word list was
compiled and several experiments have been performed to evaluate
the quality of the synthesized speech by analyzing the Mean Opinion
Score (MOS) obtained. The overall performance of the system as
well as the room for improvements was thoroughly discussed.
Abstract: This paper presents two different sequential switching hybrid-modulation strategies and implemented for cascaded multilevel inverters. Hybrid modulation strategies represent the combinations of Fundamental-frequency pulse width modulation (FFPWM) and Multilevel sinusoidal-modulation (MSPWM) strategies, and are designed for performance of the well-known Alternative Phase opposition disposition (APOD), Phase shifted carrier (PSC). The main characteristics of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells. The feasibility of these modulations is verified through spectral analysis, power loss analysis and simulation.
Abstract: Since 2004, we have been developing an in-situ storage image sensor (ISIS) that captures more than 100 consecutive images at a frame rate of 10 Mfps with ultra-high sensitivity as well as the video camera for use with this ISIS. Currently, basic research is continuing in an attempt to increase the frame rate up to 100 Mfps and above. In order to suppress electro-magnetic noise at such high frequency, a digital-noiseless imaging transfer scheme has been developed utilizing solely sinusoidal driving voltages. This paper presents highly efficient-yet-accurate expressions to estimate attenuation as well as phase delay of driving voltages through RC networks of an ultra-high-speed image sensor. Elmore metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE data, we found a simple expression that significantly improves the accuracy of the approximation. Similarly, another simple closed-form model to estimate phase delay through fundamental RC networks is also obtained. Estimation error of both expressions is much less than previous works, only less 2% for most of the cases . The framework of this analysis can be extended to address similar issues of other VLSI structures.
Abstract: The intelligent fuzzy input estimator is used to estimate
the input force of the rigid bar structural system in this study. The
fuzzy Kalman filter without the input term and the fuzzy weighting
recursive least square estimator are two main portions of this method.
The practicability and accuracy of the proposed method were verified
with numerical simulations from which the input forces of a rigid bar
structural system were estimated from the output responses. In order to
examine the accuracy of the proposed method, a rigid bar structural
system is subjected to periodic sinusoidal dynamic loading. The
excellent performance of this estimator is demonstrated by comparing
it with the use of difference weighting function and improper the
initial process noise covariance. The estimated results have a good
agreement with the true values in all cases tested.
Abstract: The experimental and theoretical results of a ZVS
(Zero Voltage Switching) isolated flyback DC-DC converter using
multilayered coreless PCB step down 2:1 transformer are presented.
The performance characteristics of the transformer are shown which
are useful for the parameters extraction. The measured energy
efficiency of the transformer is found to be more than 94% with the
sinusoidal input voltage excitation. The designed flyback converter
has been tested successfully upto the output power level of 10W,
with a switching frequency in the range of 2.7MHz-4.3MHz. The
input voltage of the converter is varied from 25V-40V DC.
Frequency modulation technique is employed by maintaining
constant off time to regulate the output voltage of the converter. The
energy efficiency of the isolated flyback converter circuit under ZVS
condition in the MHz frequency region is found to be approximately
in the range of 72-84%. This paper gives the comparative results in
terms of the energy efficiency of the hard switched and soft switched
flyback converter in the MHz frequency region.
Abstract: This paper presents a comparison between two Pulse
Width Modulation (PWM) algorithms applied to a three-level Neutral
Point Clamped (NPC) Voltage Source Inverter (VSI). The first
algorithm applied is the triangular-sinusoidal strategy; the second is
the Space Vector Pulse Width Modulation (SVPWM) strategy. In the
first part, we present a topology of three-level NCP VSI. After that,
we develop the two PWM strategies to control this converter. At the
end the experimental results are presented.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: Computed tomography and laminography are heavily investigated in a compressive sensing based image reconstruction framework to reduce the dose to the patients as well as to the radiosensitive devices such as multilayer microelectronic circuit boards. Nowadays researchers are actively working on optimizing the compressive sensing based iterative image reconstruction algorithm to obtain better quality images. However, the effects of the sampled data’s properties on reconstructed the image’s quality, particularly in an insufficient sampled data conditions have not been explored in computed laminography. In this paper, we investigated the effects of two data properties i.e. sampling density and data incoherence on the reconstructed image obtained by conventional computed laminography and a recently proposed method called spherical sinusoidal scanning scheme. We have found that in a compressive sensing based image reconstruction framework, the image quality mainly depends upon the data incoherence when the data is uniformly sampled.