Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: The dynamic or complex modulus test is considered
to be a mechanistically based laboratory test to reliably characterize
the strength and load-resistance of Hot-Mix Asphalt (HMA) mixes
used in the construction of roads. The most common observation is
that the data collected from these tests are often noisy and somewhat
non-sinusoidal. This hampers accurate analysis of the data to obtain
engineering insight. The goal of the work presented in this paper is to
develop and compare automated evolutionary computational
techniques to filter test noise in the collection of data for the HMA
complex modulus test. The results showed that the Covariance
Matrix Adaptation-Evolutionary Strategy (CMA-ES) approach is
computationally efficient for filtering data obtained from the HMA
complex modulus test.
Abstract: This paper is concerned with the study of mineralogy
and engineering characteristics of soil materials derived from the
eastern part of Nile Delta. The clay minerals of the studied soil by
using X- ray diffraction are mainly illite (average 72.6 %) and
kaolinite (average 2.6 %), expandable portion in illite-smectite mixed
layer (average 7 %). Smectite is more abundant in fluviatile clays,
whereas kaolinite is more abundant in lagoonal clays. On the other
hand, illite and illite-smectite are more abundant in marine clays. The
geotechnical results show that the soil under study consists mainly of
about 0.3 % gravel, 5 % sand, 51.5 % silt and 42.2 % clay in average.
The average shrinkage limit attains 11 % whereas the average value
of the plasticity index is 23.4 %. The free swelling ranges from 40 %
to 75 % and has a value of 55 % giving an indication about the
inadequacy of such soil under foundations.
From a construction point of view, the soil under investigation
poses many problems even under light foundations due to the
swelling and shrinkage. Such swelling and shrinkage is due to the
high content of soil materials in the expandable clay minerals of illite
and smectite. Based on the results of the present and earlier studies,
trial application of soil stabilisation is recommended.
Abstract: Two seperate experiments by barley and alfalfa were
conducted to a 2×8 factorial completely randomised design, with four
replicates. Factors were inoculation (M) with Gomus mosseae or uninoculation
(M0) and seven levels of contaminants (Co, Cd, Pb and
combinations) plus an uncontaminated control treatment (C). Heavy
metals in plant tissues and soil were quantified by Inductively
Coupled Plasma Optical Emission Spectrometer (ICP-OES) (Variant-
Liberty 150AX Turbo). Phytoextraction coefficient of contaminants
calculated by concentration of heavy metals in the shoot (mgkg-1) /
concentration of heavy metals in soil (mgkg-1). In the barley, the
highest rate of phytoextraction coefficient of Pb, Cd and Co was in
M0Pb, M0PbCoCd and MCo, respectively (P
Abstract: The hydro-mechanical model for unsaturated soils has
been presented based on the effective stress principle taking into
account effects of drying-wetting process. The elasto-plastic
constitutive equations for stress-strain relations of the soil skeleton
have been established. A plasticity model is modified from modified
Cam-Clay model. The hardening rule has been established by
considering the isotropic consolidation paths. The effect of dryingwetting
process is introduced through the ¤ç parameter. All model
coefficients are identified in terms of measurable parameters. The
simulations from the proposed model are compared with the
experimental results. The model calibration was performed to extract
the model parameter from the experimental results. Good agreement
between the results predicted using proposed model and the
experimental results was obtained.
Abstract: Soil erosion is the most serious problem faced at
global and local level. So planning of soil conservation measures has
become prominent agenda in the view of water basin managers. To
plan for the soil conservation measures, the information on soil
erosion is essential. Universal Soil Loss Equation (USLE), Revised
Universal Soil Loss Equation 1 (RUSLE1or RUSLE) and Modified
Universal Soil Loss Equation (MUSLE), RUSLE 1.06, RUSLE1.06c,
RUSLE2 are most widely used conventional erosion estimation
methods. The essential drawbacks of USLE, RUSLE1 equations are
that they are based on average annual values of its parameters and so
their applicability to small temporal scale is questionable. Also these
equations do not estimate runoff generated soil erosion. So
applicability of these equations to estimate runoff generated soil
erosion is questionable. Data used in formation of USLE, RUSLE1
equations was plot data so its applicability at greater spatial scale
needs some scale correction factors to be induced. On the other hand
MUSLE is unsuitable for predicting sediment yield of small and large
events. Although the new revised forms of USLE like RUSLE 1.06,
RUSLE1.06c and RUSLE2 were land use independent and they have
almost cleared all the drawbacks in earlier versions like USLE and
RUSLE1, they are based on the regional data of specific area and
their applicability to other areas having different climate, soil, land
use is questionable. These conventional equations are applicable for
sheet and rill erosion and unable to predict gully erosion and spatial
pattern of rills. So the research was focused on development of nonconventional
(other than conventional) methods of soil erosion
estimation. When these non-conventional methods are combined with
GIS and RS, gives spatial distribution of soil erosion. In the present
paper the review of literature on non- conventional methods of soil
erosion estimation supported by GIS and RS is presented.
Abstract: This study presents the application of artificial
neural network for modeling the phenolic compound
migration through vertical soil column. A three layered feed
forward neural network with back propagation training
algorithm was developed using forty eight experimental data
sets obtained from laboratory fixed bed vertical column tests.
The input parameters used in the model were the influent
concentration of phenol(mg/L) on the top end of the soil
column, depth of the soil column (cm), elapsed time after
phenol injection (hr), percentage of clay (%), percentage of
silt (%) in soils. The output of the ANN was the effluent
phenol concentration (mg/L) from the bottom end of the soil
columns. The ANN predicted results were compared with the
experimental results of the laboratory tests and the accuracy of
the ANN model was evaluated.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: Construction of portable device for fast analysis of energetic materials is described in this paper. The developed analytical system consists of two main parts: a miniaturized microcolumn liquid chromatograph of unique construction and original chemiluminescence detector. This novel portable device is able to determine selectively most of nitramine- and nitroester-based explosives as well as inorganic nitrates at trace concentrations in water or soil extracts in less than 8 minutes.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: Moisture is an important consideration in many
aspects ranging from irrigation, soil chemistry, golf course, corrosion
and erosion, road conditions, weather predictions, livestock feed
moisture levels, water seepage etc. Vegetation and crops always
depend more on the moisture available at the root level than on
precipitation occurrence. In this paper, design of an instrument is
discussed which tells about the variation in the moisture contents of
soil. This is done by measuring the amount of water content in soil by
finding the variation in capacitance of soil with the help of a
capacitive sensor. The greatest advantage of soil moisture sensor is
reduced water consumption. The sensor is also be used to set lower
and upper threshold to maintain optimum soil moisture saturation and
minimize water wilting, contributes to deeper plant root growth
,reduced soil run off /leaching and less favorable condition for insects
and fungal diseases. Capacitance method is preferred because, it
provides absolute amount of water content and also measures water
content at any depth.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: An experiment was implemented in a filed in the south of Morocco to evaluate the effects of domestic treated wastewater use for irrigation of amaranth crop under semi-arid conditions. Three varieties (A0020, A0057 & A211) were tested and irrigated using domestic treated wastewater EC1 (0,92 dS/m) as control, EC3 (3dS/m) and EC6 (6dS/m) obtained by adding sea water. In term of growth, an increase of the EC level of applied irrigation water reduced significantly the plant-s height, leaf area, fresh and dry weight measured at vegetative, flowering and maturity stage for all varieties. Even with the application of the EC6, yields were relatively higher in comparison with the once obtained in normal cultivation conditions. A significant accumulation of nitrate, chloride and sodium in soil layers during the crop cycle was noted. The use of treated waste water for its irrigation is proved to be possible. The variety A211 had showed to be less sensitive to salinity stress and it could be more promising its introduction to study area.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.
Abstract: Saturated hydraulic conductivity of Soil is an
important property in processes involving water and solute flow in
soils. Saturated hydraulic conductivity of soil is difficult to measure
and can be highly variable, requiring a large number of replicate
samples. In this study, 60 sets of soil samples were collected at
Saqhez region of Kurdistan province-IRAN. The statistics such as
Correlation Coefficient (R), Root Mean Square Error (RMSE), Mean
Bias Error (MBE) and Mean Absolute Error (MAE) were used to
evaluation the multiple linear regression models varied with number
of dataset. In this study the multiple linear regression models were
evaluated when only percentage of sand, silt, and clay content (SSC)
were used as inputs, and when SSC and bulk density, Bd, (SSC+Bd)
were used as inputs. The R, RMSE, MBE and MAE values of the 50
dataset for method (SSC), were calculated 0.925, 15.29, -1.03 and
12.51 and for method (SSC+Bd), were calculated 0.927, 15.28,-1.11
and 12.92, respectively, for relationship obtained from multiple
linear regressions on data. Also the R, RMSE, MBE and MAE values
of the 10 dataset for method (SSC), were calculated 0.725, 19.62, -
9.87 and 18.91 and for method (SSC+Bd), were calculated 0.618,
24.69, -17.37 and 22.16, respectively, which shows when number of
dataset increase, precision of estimated saturated hydraulic
conductivity, increases.
Abstract: The objective of this research is to study principal
component analysis for classification of 67 soil samples collected from
different agricultural areas in the western part of Thailand. Six soil
properties were measured on the soil samples and are used as original
variables. Principal component analysis is applied to reduce the
number of original variables. A model based on the first two
principal components accounts for 72.24% of total variance. Score
plots of first two principal components were used to map with
agricultural areas divided into horticulture, field crops and wetland.
The results showed some relationships between soil properties and
agricultural areas. PCA was shown to be a useful tool for agricultural
areas classification based on soil properties.
Abstract: The volume of biosolids produced in Malaysia
nowadays had increased proportionally to its population size. The end
products from the waste treatments were mounting, thus inevitable
that in the end the environment will be surrounded by the waste. This
study was conducted to investigate the suitability of biosolids to be
reused as fertilizer for non-food crop. By varying the concentration of
biosolids applied onto the soil, growth of five ornamental plant
samples were tested for eight consecutive weeks. The results show
that the pH of the soil after the addition of biosolids ranges from 6.45
to 6.56 which is suitable for the plant growth. The soil samples that
contains biosolid also show higher amount of macronutrients (N, P,
K) and the heavy metals content are significantly increased in the
plant however it does not exceed the guidelines drawn by the
Environmental Protection Agency. It is also proven that there was
only small significant different in the performance of plant growth
between biosolids and commercial fertilizer. It can be seen that
biosolids was able to perform just as well as commercial fertilizer.
Abstract: Sediment formation and its transport along the river course is considered as important hydraulic consideration in river engineering. Their impact on the morphology of rivers on one hand and important considerations of which in the design and construction of the hydraulic structures on the other has attracted the attention of experts in arid and semi-arid regions. Under certain conditions where the momentum energy of the flow stream reaches a specific rate, the sediment materials start to be transported with the flow. This can usually be analyzed in two different categories of suspended and bed load materials. Sedimentation phenomenon along the waterways and the conveyance of vast volume of materials into the canal networks can potentially influence water abstraction in the intake structures. This can pose a serious threat to operational sustainability and water delivery performance in the canal networks. The situation is serious where ineffective watershed management (poor vegetation cover in the water basin) is the underlying cause of soil erosion which feeds the materials into the waterways that intern would necessitate comprehensive study. The present paper aims to present an analytical investigation of the sediment process in the waterways on one hand and estimation of the sediment load transport into the lined canals using the SHARC software on the other. For this reason, the paper focuses on the comparative analysis of the hydraulic behaviors of the Sabilli main canal that feeds the pumping station with that of the Western canal in the Greater Dezful region to identify effective factors in sedimentation and ways of mitigating their impact on water abstraction in the canal systems. The method involved use of observational data available in the Dezful Dastmashoon hydrometric station along a 6 km waterway of the Sabilli main canal using the SHARC software to estimate the suspended load concentration and bed load materials. Results showed the transport of a significant volume of sediment loads from the waterways into the canal system which is assumed to have arisen from the absence of stilling basin on one hand and the gravity flow on the other has caused serious challenges. This is contrary to what occurs in the Sabilli canal, where the design feature which incorporates a settling basin just before the pumping station is the major cause of reduced sediment load transport into the canal system.Results showed that modification of the present design features by constructing a settling basin just upstream of the western intake structure can considerably reduce the entry of sediment materials into the canal system. Not only this can result in the sustainability of the hydraulic structures but can also improve operational performance of water conveyance and distribution system, all of which are the pre-requisite to secure reliable and equitable water delivery regime for the command area.
Abstract: Nonlinear finite element method with eight noded
isoparametric quadrilateral element is used for prediction of loaddeformation
behavior including bearing capacity of foundations.
Modified generalized plasticity model with non-associated flow rule
is applied for analysis of soil-footing system. Also Von Mises and
Tresca criterions are used for simulation of soil behavior. Modified
generalized plasticity model is able to simulate load-deformation
including softening behavior. Localization phenomena are considered
by different meshes. Localization phenomena have not been seen in
the examples. Predictions by modified generalized plasticity model
show good agreement with laboratory data and theoretical prediction
in comparison the other models.