Abstract: This paper presents the comparison ageing deterioration of silicone rubber housing material for outdoor polymer insulators by using salt fog ageing test based on IEC 61109 and outdoor exposure test.Four types of high temperature silicone vulcanized silicone rubber sheet with different amount of ATH were used as testing specimen. For salt fog ageing test, the specimens were tested continuously 1000 hours with energized in test chamber. For outdoor exposure test, the specimens were hung continuously 18 months without energized. Physical and chemical analyses were conducted to evaluate degree of ageing deterioration of tested specimens. Slightly surface erosion was observed on specimen surface after salt fog ageing test and no erosion was observed on surface of outdoor exposure specimen. However, comparable degree of ageing deterioration can be seen from surface analysis results.
Abstract: A model of vortex wake is suggested to determine the
induced power during animal hovering flight. The wake is modeled
by a series of equi-spaced rigid rectangular vortex plates, positioned
horizontally and moving vertically downwards with identical speeds;
each plate is generated during powering of the functionally wing
stroke. The vortex representation of the wake considered in the
current theory allows a considerable loss of momentum to occur. The
current approach accords well with the nature of the wingbeat since it
considers the unsteadiness in the wake as an important fluid
dynamical characteristic. Induced power in hovering is calculated as
the aerodynamic power required to generate the vortex wake system.
Specific mean induced power to mean wing tip velocity ratio is
determined by solely the normal spacing parameter (f) for a given
wing stroke amplitude. The current theory gives much higher specific
induced power estimate than anticipated by classical methods.
Abstract: This paper presents kinematic and dynamic analysis of a novel 8-DOF hybrid robot manipulator. The hybrid robot manipulator under consideration consists of a parallel robot which
is followed by a serial mechanism. The parallel mechanism has three translational DOF, and the serial mechanism has five DOF so that the overall degree of freedom is eight. The introduced
manipulator has a wide workspace and a high capability to reduce
the actuating energy. The inverse and forward kinematic solutions are described in closed form. The theoretical results are verified by
a numerical example. Inverse dynamic analysis of the robot is presented by utilizing the Iterative Newton-Euler and Lagrange dynamic formulation methods. Finally, for performing a multi-step
arc welding process, results have indicated that the introduced manipulator is highly capable of reducing the actuating energy.
Abstract: In this paper, we seek to determine one reasonable
local hub port and optimal routes for a containership fleet,
performing pick-ups and deliveries, between the hub and spoke ports
in a same region. The relationship between a hub port, and traffic in
feeder lines is analyzed. A new network planning method is proposed,
an integrated hub port location and route design, a capacitated vehicle
routing problem with pick-ups, deliveries and time deadlines are
formulated and solved using an improved genetic algorithm for
positioning the hub port and establishing routes for a containership
fleet. Results on the performance of the algorithm and the feasibility
of the approach show that a relatively small fleet of containerships
could provide efficient services within deadlines.
Abstract: Property investment in the real estate industry has a
high risk due to the uncertainty factors that will affect the decisions
made and high cost. Analytic hierarchy process has existed for some
time in which referred to an expert-s opinion to measure the
uncertainty of the risk factors for the risk analysis. Therefore,
different level of experts- experiences will create different opinion
and lead to the conflict among the experts in the field. The objective
of this paper is to propose a new technique to measure the uncertainty
of the risk factors based on multidimensional data model and data
mining techniques as deterministic approach. The propose technique
consist of a basic framework which includes four modules: user,
technology, end-user access tools and applications. The property
investment risk analysis defines as a micro level analysis as the
features of the property will be considered in the analysis in this
paper.
Abstract: We have developed a distributed asynchronous Web
based training system. In order to improve the scalability and robustness
of this system, all contents and a function are realized on
mobile agents. These agents are distributed to computers, and they
can use a Peer to Peer network that modified Content-Addressable
Network. In this system, all computers offer the function and exercise
by themselves. However, the system that all computers do the same
behavior is not realistic. In this paper, as a solution of this issue,
we present an e-Learning system that is composed of computers
of different participation types. Enabling the computer of different
participation types will improve the convenience of the system.
Abstract: Target tracking and localization are important applications
in wireless sensor networks. In these applications, sensor nodes
collectively monitor and track the movement of a target. They have
limited energy supplied by batteries, so energy efficiency is essential
for sensor networks. Most existing target tracking protocols need to
wake up sensors periodically to perform tracking. Some unnecessary
energy waste is thus introduced. In this paper, an energy efficient
protocol for target localization is proposed. In order to preserve
energy, the protocol fixes the number of sensors for target tracking,
but it retains the quality of target localization in an acceptable
level. By selecting a set of sensors for target localization, the other
sensors can sleep rather than periodically wake up to track the target.
Simulation results show that the proposed protocol saves a significant
amount of energy and also prolongs the network lifetime.
Abstract: Fourier transform infrared (FT-IR) spectroscopic imaging
is an emerging technique that provides both chemically and
spatially resolved information. The rich chemical content of data
may be utilized for computer-aided determinations of structure and
pathologic state (cancer diagnosis) in histological tissue sections for
prostate cancer. FT-IR spectroscopic imaging of prostate tissue has
shown that tissue type (histological) classification can be performed to
a high degree of accuracy [1] and cancer diagnosis can be performed
with an accuracy of about 80% [2] on a microscopic (≈ 6μm)
length scale. In performing these analyses, it has been observed
that there is large variability (more than 60%) between spectra from
different points on tissue that is expected to consist of the same
essential chemical constituents. Spectra at the edges of tissues are
characteristically and consistently different from chemically similar
tissue in the middle of the same sample. Here, we explain these
differences using a rigorous electromagnetic model for light-sample
interaction. Spectra from FT-IR spectroscopic imaging of chemically
heterogeneous samples are different from bulk spectra of individual
chemical constituents of the sample. This is because spectra not
only depend on chemistry, but also on the shape of the sample.
Using coupled wave analysis, we characterize and quantify the nature
of spectral distortions at the edges of tissues. Furthermore, we
present a method of performing histological classification of tissue
samples. Since the mid-infrared spectrum is typically assumed to
be a quantitative measure of chemical composition, classification
results can vary widely due to spectral distortions. However, we
demonstrate that the selection of localized metrics based on chemical
information can make our data robust to the spectral distortions
caused by scattering at the tissue boundary.
Abstract: Ramadan requires individuals to abstain from food and fluid intake between sunrise and sunset; physiological considerations predict that poorer mood, physical performance and mental performance will result. In addition, any difficulties will be worsened because preparations for fasting and recovery from it often mean that nocturnal sleep is decreased in length, and this independently affects mood and performance.
A difficulty of interpretation in many studies is that the observed changes could be due to fasting but also to the decreased length of sleep and altered food and fluid intakes before and after the daytime fasting. These factors were separated in this study, which took place over three separate days and compared the effects of different durations of fasting (4, 8 or 16h) upon a wide variety of measures (including subjective and objective assessments of performance, body composition, dehydration and responses to a short bout of exercise) - but with an unchanged amount of nocturnal sleep, controlled supper the previous evening, controlled intakes at breakfast and daytime naps not being allowed. Many of the negative effects of fasting observed in previous studies were present in this experiment also. These findings indicate that fasting was responsible for many of the changes previously observed, though some effect of sleep loss, particularly if occurring on successive days (as would occur in Ramadan) cannot be excluded.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In this paper we present semantic assistant agent
(SAA), an open source digital library agent which takes user query
for finding information in the digital library and takes resources-
metadata and stores it semantically. SAA uses Semantic Web to
improve browsing and searching for resources in digital library. All
metadata stored in the library are available in RDF format for
querying and processing by SemanSreach which is a part of SAA
architecture. The architecture includes a generic RDF-based model
that represents relationships among objects and their components.
Queries against these relationships are supported by an RDF triple
store.
Abstract: Appropriate description of business processes through
standard notations has become one of the most important assets for
organizations. Organizations must therefore deal with quality faults
in business process models such as the lack of understandability and
modifiability. These quality faults may be exacerbated if business
process models are mined by reverse engineering, e.g., from existing
information systems that support those business processes. Hence,
business process refactoring is often used, which change the internal
structure of business processes whilst its external behavior is
preserved. This paper aims to choose the most appropriate set of
refactoring operators through the quality assessment concerning
understandability and modifiability. These quality features are
assessed through well-proven measures proposed in the literature.
Additionally, a set of measure thresholds are heuristically established
for applying the most promising refactoring operators, i.e., those that
achieve the highest quality improvement according to the selected
measures in each case.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: For more than 120 years, gold mining formed the
backbone the South Africa-s economy. The consequence of mine
closure was observed in large-scale land degradation and widespread
pollution of surface water and groundwater. This paper investigates
the feasibility of using natural zeolite in removing heavy metals
contaminating the Wonderfonteinspruit Catchment Area (WCA), a
water stream with high levels of heavy metals and radionuclide
pollution. Batch experiments were conducted to study the adsorption
behavior of natural zeolite with respect to Fe2+, Mn2+, Ni2+, and Zn2+.
The data was analysed using the Langmuir and Freudlich isotherms.
Langmuir was found to correlate the adsorption of Fe2+, Mn2+, Ni2+,
and Zn2+ better, with the adsorption capacity of 11.9 mg/g, 1.2 mg/g,
1.3 mg/g, and 14.7 mg/g, respectively. Two kinetic models namely,
pseudo-first order and pseudo second order were also tested to fit the
data. Pseudo-second order equation was found to be the best fit for
the adsorption of heavy metals by natural zeolite. Zeolite
functionalization with humic acid increased its uptake ability.
Abstract: Short Message Service (SMS) has grown in
popularity over the years and it has become a common way of
communication, it is a service provided through General System
for Mobile Communications (GSM) that allows users to send text
messages to others.
SMS is usually used to transport unclassified information, but
with the rise of mobile commerce it has become a popular tool for
transmitting sensitive information between the business and its
clients. By default SMS does not guarantee confidentiality and
integrity to the message content.
In the mobile communication systems, security (encryption)
offered by the network operator only applies on the wireless link.
Data delivered through the mobile core network may not be
protected. Existing end-to-end security mechanisms are provided
at application level and typically based on public key
cryptosystem.
The main concern in a public-key setting is the authenticity of
the public key; this issue can be resolved by identity-based (IDbased)
cryptography where the public key of a user can be derived
from public information that uniquely identifies the user.
This paper presents an encryption mechanism based on the IDbased
scheme using Elliptic curves to provide end-to-end security
for SMS. This mechanism has been implemented over the standard
SMS network architecture and the encryption overhead has been
estimated and compared with RSA scheme. This study indicates
that the ID-based mechanism has advantages over the RSA
mechanism in key distribution and scalability of increasing
security level for mobile service.
Abstract: Using mobile Internet access technologies and eservices,
various economic agents can efficiently offer their products
or services to a large number of clients. With the support of mobile
communications networks, the clients can have access to e-services,
anywhere and anytime. This is a base to establish a convergence of
technological and financial interests of mobile operators, software
developers, mobile terminals producers and e-content providers. In
this paper, a client server system is presented, using 3G, EDGE,
mobile terminals, for Stock Exchange e-services access.
Abstract: The purpose of this article is to analyze the market structure as well as the degree of concentration in insurance markets in new EU member states. The analysis was conducted using several most commonly used concentration indicators such as concentration ratio, Herfindahl-Hirschman index and entropy index. These indicators were calculated for the 2000-2010 period on the basis of total gross written premium as the most relevant indicator of market power in insurance markets. The results of the analysis showed that in all observed countries the level of concentration decreased, though with significantly different intensity. Yet, in some countries, the level of concentration remains very high.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: The Inter feeder Power Flow Regulator (IFPFR)
proposed in this paper consists of several voltage source inverters
with common dc bus; each inverter is connected in series with one of
different independent distribution feeders in the power system. This
paper is concerned with how to transfer power between the feeders for
load sharing purpose. The power controller of each inverter injects
the power (for sending feeder) or absorbs the power (for receiving
feeder) via injecting suitable voltage; this voltage injection is
simulated by voltage drop across series virtual impedance, the
impedance value is selected to achieve the concept of power exchange
between the feeders without perturbing the load voltage magnitude of
each feeder. In this paper a new control scheme for load sharing using
IFPFR is proposed.