Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.
Abstract: This report examines the current state of human gait
simulator development based on the human hip joint model. This unit
will create a database of human gait types, useful for setting up and
calibrating Mechano devices, as well as the creation of new systems
of rehabilitation, exoskeletons and walking robots. The system has
many opportunities to configure the dimensions and stiffness, while
maintaining relative simplicity.
Abstract: Common Platform for Automated Programming
(CPAP) is defined in details. Two versions of CPAP are described:
Cloud based (including set of components for classic programming,
and set of components for combined programming); and Knowledge
Based Automated Software Engineering (KBASE) based (including
set of components for automated programming, and set of
components for ontology programming). Four KBASE products
(Module for Automated Programming of Robots, Intelligent Product
Manual, Intelligent Document Display, and Intelligent Form
Generator) are analyzed and CPAP contributions to automated
programming are presented.
Abstract: Finding the optimal 3D path of an aerial vehicle under
flight mechanics constraints is a major challenge, especially when
the algorithm has to produce real time results in flight. Kinematics
models and Pythagorian Hodograph curves have been widely used
in mobile robotics to solve this problematic. The level of difficulty
is mainly driven by the number of constraints to be saturated at the
same time while minimizing the total length of the path. In this paper,
we suggest a pragmatic algorithm capable of saturating at the same
time most of dimensioning helicopter 3D trajectories’ constraints
like: curvature, curvature derivative, torsion, torsion derivative, climb
angle, climb angle derivative, positions. The trajectories generation
algorithm is able to generate versatile complex 3D motion primitives
feasible by a helicopter with parameterization of the curvature and the
climb angle. An upper ”motion primitives’ concatenation” algorithm
is presented based. In this article we introduce a new way of designing
three-dimensional trajectories based on what we call the ”Dubins
gliding symmetry conjecture”. This extremely performing algorithm
will be soon integrated to a real-time decisional system dealing with
inflight safety issues.
Abstract: Software testing has become a mandatory process in
assuring the software product quality. Hence, test management is
needed in order to manage the test activities conducted in the
software test life cycle. This paper discusses on the challenges faced
in the software test life cycle, and how the test processes and test
activities, mainly on test cases creation, test execution, and test
reporting is being managed and automated using several test
automation tools, i.e. Jira, Robot Framework, and Jenkins.
Abstract: For a rigid body sliding on a rough surface, a range of
uncertainty or non-uniqueness of solution could be found, which is
termed: Painlevé paradox. Painlevé paradox is the reason of a wide
range of bouncing motion, observed during sliding of robotic
manipulators on rough surfaces. In this research work, the existence
of the paradox zone during the sliding motion of a two-link (P-R)
robotic manipulator with a unilateral constraint is investigated.
Parametric study is performed to investigate the effect of friction,
link-length ratio, total height and link-mass ratio on the paradox zone.
Abstract: Recently attention has been focused on incomplete
spinal cord injuries (SCI) to the central spine caused by pressure on
parts of the white matter conduction pathway, such as the pyramidal
tract. In this paper, we focus on a training robot designed to assist with
primary walking-pattern training. The target patient for this training
robot is relearning the basic functions of the usual walking pattern; it is
meant especially for those with incomplete-type SCI to the central
spine, who are capable of standing by themselves but not of
performing walking motions. From the perspective of human
engineering, we monitored the operator’s actions to the robot and
investigated the movement of joints of the lower extremities, the
circumference of the lower extremities, and exercise intensity with the
machine. The concept of the device was to provide mild training
without any sudden changes in heart rate or blood pressure, which will
be particularly useful for the elderly and disabled. The mechanism of
the robot is modified to be simple and lightweight with the expectation
that it will be used at home.
Abstract: The paper presents an advanced control system for
tennis ball throwing machines to improve their accuracy according to
the ball impact points. A further advantage of the system is the much
easier calibration process involving the intelligent solution of the
automatic adjustment of the stroking parameters according to the ball
elasticity, the self-calibration, the use of the safety margin at very flat
strokes and the possibility to placing the machine to any position of
the half court. The system applies mathematical methods to
determine the exact ball trajectories and special approximating
processes to access all points on the aimed half court.
Abstract: This paper presents modeling and simulation of
flexible robot in an underwater environment. The underwater
environment completely contrasts with ground or space environment.
The robot in an underwater situation is subjected to various dynamic
forces like buoyancy forces, hydrostatic and hydrodynamic forces.
The underwater robot is modeled as Rayleigh beam. The developed
model further allows estimating the deflection of tip in two
directions. The complete dynamics of the underwater robot is
analyzed, which is the main focus of this investigation. The control of
robot trajectory is not discussed in this paper. Simulation is
performed using Symbol Shakti software.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: The main purpose of this study is static analysis of
two three-degree of freedom parallel mechanisms: 3-RCC and 3-
RRS. Geometry of these mechanisms is expressed and static
equilibrium equations are derived for the whole chains. For these
mechanisms due to the equal number of equations and unknowns, the
solution is as same as 3-RCC mechanism. A mathematical software is
used to solve the equations. In order to prove the results obtained
from solving the equations of mechanisms, the CAD model of these
robots has been simulated and their static is analysed in ADAMS
software. Due to symmetrical geometry of the mechanisms, the force
and external torque acting on the end-effecter have been considered
asymmetric to prove the generality of the solution method. Finally,
the results of both softwares, for both mechanisms are extracted and
compared as graphs. The good achieved comparison between the
results indicates the accuracy of the analysis.
Abstract: In this paper a new model for center of motion
creating is proposed. This new method uses cables. So, it is very
useful in robots because it is light and has easy assembling process.
In the robots which need to be in touch with some things this method
is so useful. It will be described in the following. The accuracy of the
idea is proved by two experiments. This system could be used in the
robots which need a fixed point in the contact with some things and
make a circular motion.
Abstract: In this paper, we introduce an NLG application for the automatic creation of ready-to-publish texts from big data. The resulting fully automatic generated news stories have a high resemblance to the style in which the human writer would draw up such a story. Topics include soccer games, stock exchange market reports, and weather forecasts. Each generated text is unique. Readyto-publish stories written by a computer application can help humans to quickly grasp the outcomes of big data analyses, save timeconsuming pre-formulations for journalists and cater to rather small audiences by offering stories that would otherwise not exist.
Abstract: Image segmentation and color identification is an
important process used in various emerging fields like intelligent
robotics. A method is proposed for the manipulator to grasp and place
the color object into correct location. The existing methods such as
PSO, has problems like accelerating the convergence speed and
converging to a local minimum leading to sub optimal performance.
To improve the performance, we are using watershed algorithm and
for color identification, we are using EPSO. EPSO method is used to
reduce the probability of being stuck in the local minimum. The
proposed method offers the particles a more powerful global
exploration capability. EPSO methods can determine the particles
stuck in the local minimum and can also enhance learning speed as
the particle movement will be faster.
Abstract: This paper pioneers Care Robot Impact Assessment
(CRIA), a methodology used to identify, analyze, mitigate and
eliminate the risks posed by the insertion of non-medical personal
care robots (PCR) in medical care facilities. Its precedent instruments
[Privacy and Surveillance Impact Assessment (PIA and SIA)] fall
behind in coping with robots. Indeed, personal care robots change
dramatically how care is delivered. The paper presents a specific
risk-sector methodology, identifies which robots are under its scope
and presents some of the challenges introduced by these robots.
Abstract: The problem of finding control laws for underactuated
systems has attracted growing attention since these systems are
characterized by the fact that they have fewer actuators than the
degrees of freedom to be controlled. The acrobot, which is a planar
two-link robotic arm in the vertical plane with an actuator at the elbow
but no actuator at the shoulder, is a representative in underactuated
systems. In this paper, the dynamic model of the acrobot is
implemented using Mathworks’ Simscape. And the sliding mode
control is constructed using MATLAB and Simulink.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: A Japanese manga character, Doraemon, was made by
Fujiko F. Fujio in 1969, was made into animation in 1973. The main
character, Doraemon, is a robot cat, and is a well-known Japanese
animated character. However, Doraemon is not only regarded as an
animation character but it is also used in educational and technological
programs in Japan.
This paper focuses on the background of Doraemon, educational
and technological perspectives on Doraemon, and comparison of the
original Japanese animation and the US remade version, and the
animator Fujiko’s dreams and hopes for Doraemon will be examined.
Since Doraemon has been exported as animation and manga to
overseas, perspectives toward Doraemon have changed. For example,
changes of stories and characters can been seen in the present
Doraemon animation. Not only the overseas TV productions which
broadcast Doraemon but also the Japanese production has to consider
violence, sexuality, etc. when editing episodes. Because of
representation of cultural differences, Japanese animation is thought to
contain more violence, discrimination, and sexuality in animation.
With responses from overseas, the Japanese production was cautious
about the US remade version. They cared about the US Broadcast
Standard, and tried to consider US customs and culture in the US
remade version. Seeing the difference, acculturation is necessary for
exports of animation overseas. Moreover, observing different aspects
of Doraemon domestically, Doraemon provides dreams and hopes to
children.