Abstract: In this paper, a design of ultra wideband (UWB) printed microstrip antennas that fed by microstrip transmission line were presented and printed on a substrate Taconic TLY-5 material with relative dielectric constant of 2.2. The proposed antennas were designed to cover the frequency range of 3.5 to 12 GHz. The antennas of printed patch shapes are rectangular, triangle/rectangular, hexagonal, and circular with the same dimensions of feeder and ground plane. The proposed antennas were simulated using a package of CST microwave studio in the 2 to 12 GHz operating frequency range. Simulation results and comparison for return loss (S11), radiation patterns, and voltage standing wave ratio (VSWR) were presented and discussed over the UWB frequency.
Abstract: A low profile planar antenna for twelve-band operation in the mobile phone is presented. The proposed antenna radiating elements occupy an area equals 17 × 50 mm2 are mounted on the compact no-ground portion of the system circuit board to achieve a simple low profile structure. In order to overcome the shortcoming of narrow bandwidth for conventional planar printed antenna, a novel bandwidth enhancement approach for multiband handset antennas is proposed here. The technique used in this study shows that by using a coupled-fed mechanism and a slotted ground structure, a multiband operation with wideband characteristic can be achieved. The influences of the modifications introduced into the ground plane improved significantly the bandwidths of the designed antenna. The slotted ground plane structure with the coupled-fed elements contributes their lowest, middle and higher-order resonant modes to form four operating modes. The generated modes are able to cover LTE 700/2300/2500, GSM 850/900/1800/1900, UMTS, WiMAX 3500, WLAN 2400/5200/5800 operations. Parametric studies via simulation are provided and discussed. Proposed antenna’s gain, efficiency and radiation pattern characteristics over the desired operating bands are obtained and discussed. The reasonable results observed can meet the requirements of practical mobile phones.
Abstract: The paper describes new concept of the ribbon beam antenna for RFID technology. Antenna is located near to railway lines to monitor tags situated on trains. Antenna works at 2.45 GHz and it is fabricated by microstrip technology. Antenna contains two same mirrored parts having the same radiation patterns. Each part consists of three dielectric layers. The first layer has on one side radiation elements. The second layer is only for mechanical construction and it sets optimal electromagnetic field for each radiating elements. The third layer has on its top side a ground plane and on the bottom side a microstrip circuit used for individual radiation elements feeding.
Abstract: In this paper a novel ultra-wideband (UWB) slot antenna with band notch characteristics for world interoperability for microwave access (WiMAX) is proposed. The designed antenna consists of a rectangular radiating patch and a ground plane with tapered shape slot. To realize a notch band, a curved parasitic element has been etched out along with the radiating patch. It is observed that by adjusting the length, thickness and position of the parasitic element, the proposed antenna can achieved an impedance bandwidth of 8.01GHz (2.84 to 10.85GHz) with a notched band of 3.28-3.85GHz. Compared to the recently reported band notch antennas, the proposed antenna has a simple configuration to realize band notch characteristics in order to mitigate the potential interference between WiMAX and UWB system. Furthermore, a stable radiation pattern and moderate gain except at the notched band makes the proposed antenna suitable for various UWB applications.
Abstract: Here we have considered non uniform microstrip
leaky-wave antenna implemented on a dielectric waveguide by a
sinusoidal profile of periodic metallic grating. The non distribution of
the attenuation constant α along propagation axis, optimize the
radiating characteristics and performances of such antennas. The
method developped here is based on an integral method where the
formalism of the admittance operator is combined to a BKW
approximation. First, the effect of the modeling in the modal analysis
of complex waves is studied in detail. Then, the BKW model is used
for the dispersion analysis of the antenna of interest. According to
antenna theory, a forced continuity of the leaky-wave magnitude at
discontinuities of the non uniform structure is established. To test the
validity of our dispersion analysis, computed radiation patterns are
presented and compared in the millimeter band.
Abstract: This paper describes the development of a fully
automated measurement software for antenna radiation pattern
measurements in a Compact Antenna Test Range (CATR). The
CATR has a frequency range from 2-40 GHz and the measurement
hardware includes a Network Analyzer for transmitting and
Receiving the microwave signal and a Positioner controller to control
the motion of the Styrofoam column. The measurement process
includes Calibration of CATR with a Standard Gain Horn (SGH)
antenna followed by Gain versus angle measurement of the Antenna
under test (AUT). The software is designed to control a variety of
microwave transmitter / receiver and two axis Positioner controllers
through the standard General Purpose interface bus (GPIB) interface.
Addition of new Network Analyzers is supported through a slight
modification of hardware control module. Time-domain gating is
implemented to remove the unwanted signals and get the isolated
response of AUT. The gated response of the AUT is compared with
the calibration data in the frequency domain to obtain the desired
results. The data acquisition and processing is implemented in
Agilent VEE and Matlab. A variety of experimental measurements
with SGH antennas were performed to validate the accuracy of
software. A comparison of results with existing commercial
softwares is presented and the measured results are found to be
within .2 dBm.
Abstract: In this paper comparison of Reflector Antenna
analyzing techniques based on wave and ray nature of optics is
presented for an offset reflector antenna using GRASP (General
Reflector antenna Analysis Software Package) software. The results
obtained using PO (Physical Optics), PTD (Physical theory of
Diffraction), and GTD (Geometrical Theory of Diffraction) are
compared. The validity of PO and GTD techniques in regions around
the antenna, caustic behavior of GTD in main beam, and deviation of
GTD in case of near-in sidelobes of radiation pattern are discussed.
The comparison for far-out sidelobes predicted by PO, PO + PTD
and GTD is described. The effect of Direct Radiations from feed
which results in feed selection for the system is addressed.
Abstract: The paper presents the study of synthetic transmit
aperture method applying the Golay coded transmission for medical
ultrasound imaging. Longer coded excitation allows to increase the
total energy of the transmitted signal without increasing the peak
pressure. Signal-to-noise ratio and penetration depth are improved
maintaining high ultrasound image resolution.
In the work the 128-element linear transducer array with 0.3 mm
inter-element spacing excited by one cycle and the 8 and 16-bit
Golay coded sequences at nominal frequencies 4 MHz was used.
Single element transmission aperture was used to generate a spherical
wave covering the full image region and all the elements received the
echo signals. The comparison of 2D ultrasound images of the wire
phantom as well as of the tissue mimicking phantom is presented to
demonstrate the benefits of the coded transmission. The results were
obtained using the synthetic aperture algorithm with transmit and
receive signals correction based on a single element directivity
function.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.
Abstract: Infrared communication in the wavelength band 780-
950 nm is very suitable for short-range point-to-point communications.
It is a good choice for vehicle-to-vehicle communication in several
intelligent-transportation-system (ITS) applications such as cooperative
driving, collision warning, and pileup-crash prevention. In this
paper, with the aid of a physical model established in our previous
works, we explore the communication area of an infrared intervehicle
communication system utilizing a typical low-cost cormmercial lightemitting
diodes (LEDs) as the emitter and planar p-i-n photodiodes
as the receiver. The radiation pattern of the emitter fabricated by
aforementioned LEDs and the receiving pattern of the receiver are
approximated by a linear combination of cosinen functions. This
approximation helps us analyze the system performance easily. Both
multilane straight-road conditions and curved-road conditions with
various radius of curvature are taken into account. The condition of
a small car communicating with a big truck, i.e., there is a vertical
mounting height difference between the emitter and the receiver, is
also considered. Our results show that the performance of the system
meets the requirement of aforementioned ITS applications in terms
of the communication area.
Abstract: In the paper the study of synthetic transmit aperture
method applying the Golay coded transmission for medical
ultrasound imaging is presented. Longer coded excitation allows to
increase the total energy of the transmitted signal without increasing
the peak pressure. Moreover signal-to-noise ratio and penetration
depth are improved while maintaining high ultrasound image
resolution. In the work the 128-element linear transducer array with
0.3 mm inter-element spacing excited by one cycle and the 8 and 16-
bit Golay coded sequences at nominal frequency 4 MHz was used. To
generate a spherical wave covering the full image region a single
element transmission aperture was used and all the elements received
the echo signals. The comparison of 2D ultrasound images of the
tissue mimicking phantom and in vitro measurements of the beef liver
is presented to illustrate the benefits of the coded transmission. The
results were obtained using the synthetic aperture algorithm with
transmit and receive signals correction based on a single element
directivity function.
Abstract: Luneberg lens is a new generation of antennas that is
developed in the last few years and inserts itself strongly in
Microwaves, Communications and Telescopes area. The idea of this
research is to improve the radiation pattern by decreasing the side
lobes and increasing the main lobe. The new design is proposed to
work in the X-band. The simulated result and analysis are presented.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: UWB is a very attractive technology for many
applications. It provides many advantages such as fine resolution and high power efficiency. Our interest in the current study is the use of
UWB radar technique in microwave medical imaging systems, especially for early breast cancer detection. The Federal Communications Commission FCC allowed frequency bandwidth of
3.1 to 10.6 GHz for this purpose. In this paper we suggest an UWB Bowtie slot antenna with enhanced bandwidth. Effects of varying the geometry of the antenna
on its performance and bandwidth are studied. The proposed antenna
is simulated in CST Microwave Studio. Details of antenna design and
simulation results such as return loss and radiation patterns are discussed in this paper. The final antenna structure exhibits good
UWB characteristics and has surpassed the bandwidth requirements.
Abstract: A simple impedance matching technique for inset feed
grooved microstrip patch antenna based on the concept of coplanar
waveguide feed line has been developed and investigated for a
printed antenna at X-Band frequency of 10GHz. The proposed
technique has been used in the design of Linear Grooved Microstrip
patch antenna array. The characteristics of the antenna are
determined in terms of Return loss, VSWR, gain, radiation pattern
etc. The measured and simulated results presented are found to be in
good agreement.