Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: Eight steel reinforced concrete beams (SRC), were
fabricated and tested under earthquake type cyclic loading. The
effectiveness of intermediate stiffeners, such as mid-span stiffener and
plastic hinge zone stiffeners, in enhancing composite action and
ductility of SRC beams was investigated. The effectiveness of
strengthened beam-to-column (SBC) and weakened beam-to-column
(WBC) connections in enhancing beam ductility was also studied. It
was found that: (1) All the specimens possessed fairly high flexural
ductility and were found adequate for structures in high seismic zones.
(2) WBC connections induced stress concentration which caused extra
damage to concrete near the flange tapering zone. This extra damage
inhibited the flexural strength development and the ductility of the
specimens with WBC connections to some extent. (3) Specimens with
SBC connections demonstrated higher flexural strength and ductility
compared to specimens with WBC connections. (4) The intermediate
stiffeners, especially combination of plastic hinge zone stiffener and
mid span stiffeners, have an obvious effect in enhancing the ductility
of the beams with SBC connection.
Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.
Abstract: The dominant judgment for earthquake damaged reinforced concrete (RC) structures is to rebuild them with the new ones. Consequently, this paper estimates if there is chance to repair earthquake RC beams and obtain economical contribution to modern day society. Therefore, the totally damaged (damaged in shear under cyclic load) reinforced concrete (RC) beams repaired and strengthened by externally bonded carbon fibre reinforced polymer (CFRP) strips in this study. Four specimens, apart from the reference beam, were separated into two distinct groups. Two experimental beams in the first group primarily tested up to failure then appropriately repaired and strengthened with CFRP strips. Two undamaged specimens from the second group were not repaired but strengthened by the identical strengthening scheme as the first group for comparison. This study studies whether earthquake damaged RC beams that have been repaired and strengthened will validate similar strength and behavior to equally strengthened, undamaged RC beams. Accordingly, a strength correspondence according to strengthened specimens was acquired for the repaired and strengthened specimens. Test results confirmed that repair and strengthening, which were estimated in the experimental program, were effective for the specimens with the cracking patterns considered in the experimental program.