Abstract: In this article, we consider the estimation of P[Y < X], when strength, X and stress, Y are two independent variables of Burr Type XII distribution. The MLE of the R based on one simple iterative procedure is obtained. Assuming that the common parameter is known, the maximum likelihood estimator, uniformly minimum variance unbiased estimator and Bayes estimator of P[Y < X] are discussed. The exact confidence interval of the R is also obtained. Monte Carlo simulations are performed to compare the different proposed methods.
Abstract: Coherent and incoherent scattering cross section measurements have been carried out using a HPGe detector on elements in the range of Z = 13 - 50 using 241Am gamma rays. The cross sections have been derived by comparing the net count rate obtained from the Compton peak of aluminium with the corresponding peak of the target. The measured cross sections for the coherent and incoherent processes are compared with theoretical values and earlier reported values. Our results are in agreement with the theoretical values.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: The efficiency of an image watermarking technique depends on the preservation of visually significant information. This is attained by embedding the watermark transparently with the maximum possible strength. The current paper presents an approach for still image digital watermarking in which the watermark embedding process employs the wavelet transform and incorporates Human Visual System (HVS) characteristics. The sensitivity of a human observer to contrast with respect to spatial frequency is described by the Contrast Sensitivity Function (CSF). The strength of the watermark within the decomposition subbands, which occupy an interval on the spatial frequencies, is adjusted according to this sensitivity. Moreover, the watermark embedding process is carried over the subband coefficients that lie on edges where distortions are less noticeable. The experimental evaluation of the proposed method shows very good results in terms of robustness and transparency.
Abstract: In this paper an efficient implementation of Ripemd-
160 hash function is presented. Hash functions are a special family
of cryptographic algorithms, which is used in technological
applications with requirements for security, confidentiality and
validity. Applications like PKI, IPSec, DSA, MAC-s incorporate
hash functions and are used widely today. The Ripemd-160 is
emanated from the necessity for existence of very strong algorithms
in cryptanalysis. The proposed hardware implementation can be
synthesized easily for a variety of FPGA and ASIC technologies.
Simulation results, using commercial tools, verified the efficiency of
the implementation in terms of performance and throughput. Special
care has been taken so that the proposed implementation doesn-t
introduce extra design complexity; while in parallel functionality was
kept to the required levels.
Abstract: Mitochondria are dynamic organelles, capable to
interact with each other. While the number of mitochondria in a cell
varies, their quality and functionality depends on the operation of
fusion, fission, motility and mitophagy. Nowadays, several
researches declare as an important factor in neurogenerative diseases
the disruptions in the regulation of mitochondrial dynamics. In this
paper a stochastic model in BioAmbients calculus is presented,
concerning mitochondrial fusion and its distribution in the renewal of
mitochondrial population in a cell. This model describes the
successive and dependent stages of protein synthesis, protein-s
activation and merging of two independent mitochondria.
Abstract: Aldehydes as secondary lipid oxidation products are highly specific to the oxidative degradation of particular polyunsaturated fatty acids present in foods. Gas chromatographic analysis of those volatile compounds has been widely used for monitoring of the deterioration of food products. Developed static headspace gas chromatography method using flame ionization detector (SHS GC FID) was applied to monitor the aldehydes present in processed foods such as bakery, meat and confectionary products.
Five selected aldehydes were determined in samples without any sample preparation, except grinding for bakery and meat products. SHS–GC analysis allows the separation of propanal, pentanal, hexanal, heptanal and octanal, within 15min. Aldehydes were quantified in fresh and stored samples, and the obtained range of aldehydes in crackers was 1.62±0.05 – 9.95±0.05mg/kg, in sausages 6.62±0.46 – 39.16±0.39mg/kg; and in cocoa spread cream 0.48±0.01 – 1.13±0.02mg/kg. Referring to the obtained results, the following can be concluded, proposed method is suitable for different types of samples, content of aldehydes varies depending on the type of a sample, and differs in fresh and stored samples of the same type.
Abstract: We develop a three-step fuzzy logic-based algorithm for clustering categorical attributes, and we apply it to analyze cultural data. In the first step the algorithm employs an entropy-based clustering scheme, which initializes the cluster centers. In the second step we apply the fuzzy c-modes algorithm to obtain a fuzzy partition of the data set, and the third step introduces a novel cluster validity index, which decides the final number of clusters.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: Ground-source heat pumps achieve higher efficiencies
than conventional air-source heat pumps because they exchange heat
with the ground that is cooler in summer and hotter in winter than the
air environment. Earth heat exchangers are essential parts of the
ground-source heat pumps and the accurate prediction of their
performance is of fundamental importance. This paper presents the
development and validation of a numerical model through an
incompressible fluid flow, for the simulation of energy and
temperature changes in and around a U-tube borehole heat
exchanger. The FlexPDE software is used to solve the resulting
simultaneous equations that model the heat exchanger. The validated
model (through a comparison with experimental data) is then used to
extract conclusions on how various parameters like the U-tube
diameter, the variation of the ground thermal conductivity and
specific heat and the borehole filling material affect the temperature
of the fluid.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: the reliability analysis of the medical equipments can
help to increase the availability and the efficiency of the systems. In
this manuscript we present a simple method of decomposition that
could be easily applied on the complex medical systems. Using this
method we can easily calculate the effect of the subsystems or
components on the reliability of the overall system. Furthermore, to
investigate the effect of subsystems or components on system
performance, we perform a numerical study varying every time the
worst reliability of subsystem or component with another which has
higher reliability. It can also be useful to engineers and designers of
medical equipment, who wishes to optimize the complex systems.
Abstract: In the last decade, carbohydrates have attracted great
attention as renewable resources for the chemical industry.
Carbohydrates are abundantly found in nature in the form of
monomers, oligomers and polymers, or as components of
biopolymers and other naturally occurring substances. As natural
products, they play important roles in conferring certain physical,
chemical, and biological properties to their carrier molecules.The
synthesis of this particular carbohydrate glycomonomer is part of our
work to obtain biodegradable polymers. Our current paper describes
the synthesis and characterization of a novel carbohydrate
glycomonomer starting from D-glucose, in several synthesis steps,
that involve the protection/deprotection of the D-glucose ring via
acetylation, tritylation, then selective deprotection of the aromaticaliphatic
protective group, in order to obtain 1,2,3,4-tetra-O-acetyl-
6-O-allyl-β-D-glucopyranose. The glycomonomer was then obtained
by the allylation in drastic conditions of 1,2,3,4-tetra-O-acetyl-6-Oallyl-
β-D-glucopyranose with allylic alcohol in the presence of
stannic chloride, in methylene chloride, at room temperature. The
proposed structure of the glycomonomer, 2,3,4-tri-O-acetyl-1,6-di-
O-allyl-β-D-glucopyranose, was confirmed by FTIR, NMR and
HPLC-MS spectrometry. This glycomonomer will be further
submitted to copolymerization with certain acrylic or methacrylic
monomers in order to obtain competitive plastic materials for
applications in the biomedical field.
Abstract: In this paper, the estimation of the stress-strength
parameter R = P(Y < X), when X and Y are independent and both
are Lomax distributions with the common scale parameters but
different shape parameters is studied. The maximum likelihood
estimator of R is derived. Assuming that the common scale parameter
is known, the bayes estimator and exact confidence interval of R are
discussed. Simulation study to investigate performance of the
different proposed methods has been carried out.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: In this contribution, a way to enhance the performance of the classic Genetic Algorithm is proposed. The idea of restarting a Genetic Algorithm is applied in order to obtain better knowledge of the solution space of the problem. A new operator of 'insertion' is introduced so as to exploit (utilize) the information that has already been collected before the restarting procedure. Finally, numerical experiments comparing the performance of the classic Genetic Algorithm and the Genetic Algorithm with restartings, for some well known test functions, are given.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: In this paper, we consider nested sliding mode control of SISO nonlinear systems, perturbed by bounded matched and unmatched uncertainties. The systems are assumed to be in strict-feedback form. A step wise procedure is introduced to obtain the controller. In each step, a continuous sliding mode controller is designed as virtual control law. Then the next step sliding surface is defined by using this virtual controller. These sliding surfaces are selected as nonlinear static functions of the system states. Finally in the last step, smooth static state feedback control law is determined such that the output reaches the desired set-point while the system is forced arbitrary close to the intersection of sliding surfaces and the states remain bounded.
Abstract: Ethanol has become more attractive in fuel industry
either as fuel itself or an additive that helps enhancing the octane
number and combustibility of gasoline. This research studied a
pressure swing adsorption using cassava-based adsorbent prepared
from mixture of cassava starch and cassava pulp for dehydration of
ethanol vapor. The apparatus used in the experiments consisted of
double adsorption columns, an evaporator, and a vacuum pump. The
feed solution contained 90-92 %wt of ethanol. Three process
variables: adsorption temperatures (110, 120 and 130°C), adsorption
pressures (1 and 2 bar gauge) and feed vapor flow rate (25, 50 and 75
% valve opening of the evaporator) were investigated. According to
the experimental results, the optimal operating condition for this
system was found to be at 2 bar gauge for adsorption pressure, 120°C
for adsorption temperature and 25% valve opening of the evaporator.
Production of 1.48 grams of ethanol with concentration higher than
99.5 wt% per gram of adsorbent was obtained. PSA with cassavabased
adsorbent reported in this study could be an alternative method
for production of nearly anhydrous ethanol. Dehydration of ethanol
vapor achieved in this study is due to an interaction between free
hydroxyl group on the glucose units of the starch and the water
molecules.