Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: The purpose of this paper is applied Taguchi method on the optimization for PEMFC performance, and a representative Computational Fluid Dynamics (CFD) model is selectively performed for statistical analysis. The studied factors in this paper are pressure of fuel cell, operating temperature, the relative humidity of anode and cathode, porosity of gas diffusion electrode (GDE) and conductivity of GDE. The optimal combination for maximum power density is gained by using a three-level statistical method. The results confirmed that the robustness of the optimum design parameters influencing the performance of fuel cell are founded by pressure of fuel cell, 3atm; operating temperature, 353K; the relative humidity of anode, 50%; conductivity of GDE, 1000 S/m, but the relative humidity of cathode and porosity of GDE are pooled as error due to a small sum of squares. The present simulation results give designers the ideas ratify the effectiveness of the proposed robust design methodology for the performance of fuel cell.
Abstract: In this study, the kinetic of biogas production was studied by performing a series laboratory experiment using rumen fluid of animal ruminant as inoculums. Cattle manure as substrate was inoculated by rumen fluid to the anaerobic biodigester. Laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid by manure : rumen weight ratio of 1:1 (MR11). The operating temperatures were varied at room temperature and 38.5 oC. The cumulative volume of biogas produced was used to measure the biodigester performance. The research showed that the rumen fluid inoculated to biodigester gave significant effect to biogas production (P
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: This paper presents modeling and simulation of Grid Connected Photovoltaic (PV) system by using improved mathematical model. The model is used to study different parameter variations and effects on the PV array including operating temperature and solar irradiation level. In this paper stepped P&O algorithm is proposed for MPPT control. This algorithm will identify the suitable duty ratio in which the DC-DC converter should be operated to maximize the power output. Photo voltaic array with proposed stepped P&O-MPPT controller can operate in the maximum power point for the whole range of solar data (irradiance and temperature).
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: Green propellants used for satellite-level propulsion
system become attractive in recent years because the non-toxicity and
lower requirements of safety protection. One of the green propellants,
high-concentration hydrogen peroxide H2O2 solution (≥70% w/w,
weight concentration percentage), often known as high-test peroxide
(HTP), is considered because it is ITAR-free, easy to manufacture and
the operating temperature is lower than traditional monopropellant
propulsion. To establish satellite propulsion technology, the National
Space Organization (NSPO) in Taiwan has initialized a long-term
cooperation project with the National Cheng Kung University to
develop compatible tank and thruster. An experimental propulsion
payload has been allocated for the future self-reliant satellite to
perform orbit transfer and maintenance operations. In the present
research, an 1-Newton thruster prototype is designed and the thrusting
force is measured by a pendulum-type platform. The preliminary
hot-firing test at ambient environment showed the generated thrust and
the specific impulse are about 0.7 Newton and 102 seconds,
respectively.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: In order to investigate a PROX microreactor
performance, two-dimensional modeling of the reacting flow
between two parallel plates is performed through a finite volume
method using an improved SIMPLE algorithm. A three-step surface
kinetics including hydrogen oxidation, carbon monoxide oxidation
and water-gas shift reaction is applied for a Pt-Fe/γ-Al2O3 catalyst
and operating temperatures of about 100ºC. Flow pattern, pressure
field, temperature distribution, and mole fractions of species are
found in the whole domain for all cases. Also, the required reactive
length for removing carbon monoxide from about 2% to less than 10
ppm is found. Furthermore, effects of hydraulic diameter, wall
temperature, and inlet mole fraction of air and water are investigated
by considering carbon monoxide selectivity and conversion. It is
found that air and water addition may improve the performance of
the microreactor in carbon monoxide removal in such operating
conditions; this is in agreement with the pervious published results.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.