Abstract: In parallel with the appearance of new materials, brick masonry had and still has an essential part of the construction market today, with new technical challenges in designing bricks to meet additional requirements. Being used in structural applications, predicting the performance of clay brick masonry allows a significant cost reduction, in terms of practical experimentation. The behavior of masonry walls depends on the behavior of their elementary components, such as bricks, joints, and coatings. Therefore, it is necessary to consider it at different scales (from the scale of the intrinsic material to the real scale of the wall) and then to develop appropriate models, using numerical simulations. The work presented in this paper focuses on the mechanical characterization of the terracotta material at ambient temperature. As a result, the static Young’s modulus obtained from the flexural test shows different values in comparison with the compression test, as well as with the dynamic Young’s modulus obtained from the Impulse excitation of vibration test. Moreover, the Young's modulus varies according to the direction in which samples are extracted, where the values in the extrusion direction diverge from the ones in the orthogonal directions. Based on these results, hollow bricks can be considered as transversely isotropic bimodulus material.
Abstract: This paper provides a state estimation method for
automatic control systems of nonlinear vehicle dynamics. A nonlinear
tire model is employed to represent the realistic behavior of a vehicle.
In general, all the state variables of control systems are not precisedly
known, because those variables are observed through output sensors
and limited parts of them might be only measurable. Hence, automatic
control systems must incorporate some type of state estimation. It is
needed to establish a state estimation method for nonlinear vehicle
dynamics with restricted measurable state variables. For this purpose,
unscented Kalman filter method is applied in this study for estimating
the state variables of nonlinear vehicle dynamics. The objective of
this paper is to propose a state estimation method using unscented
Kalman filter for nonlinear vehicle dynamics. The effectiveness of
the proposed method is verified by numerical simulations.
Abstract: The environmental concerns related to global warming and ozone layer depletion along with the growing worldwide demand for heating and cooling have brought an increasing attention toward ecological and efficient Heating, Ventilation, and Air Conditioning (HVAC) systems. Furthermore, since space heating accounts for a considerable part of the European primary/final energy use, it has been identified as one of the sectors with the most challenging targets in energy use reduction. Heat pumps are commonly considered as a technology able to contribute to the achievement of the targets. Current research focuses on the full load operation and seasonal performance assessment of three gas-driven absorption heat pump cycles. To do this, investigations of the gas-driven air-source ammonia-water absorption heat pump systems for small-scale space heating applications are presented. For each of the presented cycles, both full-load under various temperature conditions and seasonal performances are predicted by means of numerical simulations. It has been considered that small capacity appliances are usually equipped with fixed geometry restrictors, meaning that the solution mass flow rate is driven by the pressure difference across the associated restrictor valve. Results show that gas utilization efficiency (GUE) of the cycles varies between 1.2 and 1.7 for both full and partial loads and vapor exchange (VX) cycle is found to achieve the highest efficiency. It is noticed that, for typical space heating applications, heat pumps operate over a wide range of capacities and thermal lifts. Thus, partially, the novelty introduced in the paper is the investigation based on a seasonal performance approach, following the method prescribed in a recent European standard (EN 12309). The overall result is a modest variation in the seasonal performance for analyzed cycles, from 1.427 (single-effect) to 1.493 (vapor-exchange).
Abstract: Controlling the flow of fluids is a challenging problem
that arises in many fields. Burgers’ equation is a fundamental
equation for several flow phenomena such as traffic, shock waves,
and turbulence. The optimal feedback control method, so-called
model predictive control, has been proposed for Burgers’ equation.
However, the model predictive control method is inapplicable to
systems whose all state variables are not exactly known. In practical
point of view, it is unusual that all the state variables of systems are
exactly known, because the state variables of systems are measured
through output sensors and limited parts of them can be only
available. In fact, it is usual that flow velocities of fluid systems
cannot be measured for all spatial domains. Hence, any practical
feedback controller for fluid systems must incorporate some type of
state estimator. To apply the model predictive control to the fluid
systems described by Burgers’ equation, it is needed to establish
a state estimation method for Burgers’ equation with limited
measurable state variables. To this purpose, we apply unscented
Kalman filter for estimating the state variables of fluid systems
described by Burgers’ equation. The objective of this study is to
establish a state estimation method based on unscented Kalman filter
for Burgers’ equation. The effectiveness of the proposed method is
verified by numerical simulations.
Abstract: The control problem of underactuated spacecrafts has
attracted a considerable amount of interest. The control method for
a spacecraft equipped with less than three control torques is useful
when one of the three control torques had failed. On the other hand,
the quantized control of systems is one of the important research
topics in recent years. The random dither quantization method that
transforms a given continuous signal to a discrete signal by adding
artificial random noise to the continuous signal before quantization
has also attracted a considerable amount of interest. The objective of
this study is to develop the control method based on random dither
quantization method for stabilizing the rotational motion of a rigid
spacecraft with two control inputs. In this paper, the effectiveness of
random dither quantization control method for the stabilization of
rotational motion of spacecrafts with two torque inputs is verified
by numerical simulations.
Abstract: For any country in the world, it has become a priority to protect the critical infrastructure from looming risks of terrorism. In any infrastructure system, the structural elements like lower floors, exterior columns, walls etc. are key elements which are the most susceptible to damage due to blast load. The present study revisits the state of art review of the design and analysis of reinforced concrete panels subjected to blast loading. Various aspects in association with blast loading on structure, i.e. estimation of blast load, experimental works carried out previously, the numerical simulation tools, various material models, etc. are considered for exploring the current practices adopted worldwide. Discussion on various parametric studies to investigate the effect of reinforcement ratios, thickness of slab, different charge weight and standoff distance is also made. It was observed that for the simulation of blast load, CONWEP blast function or equivalent numerical equations were successfully employed by many researchers. The study of literature indicates that the researches were carried out using experimental works and numerical simulation using well known generalized finite element methods, i.e. LS-DYNA, ABAQUS, AUTODYN. Many researchers recommended to use concrete damage model to represent concrete and plastic kinematic material model to represent steel under action of blast loads for most of the numerical simulations. Most of the studies reveal that the increase reinforcement ratio, thickness of slab, standoff distance was resulted in better blast resistance performance of reinforced concrete panel. The study summarizes the various research results and appends the present state of knowledge for the structures exposed to blast loading.
Abstract: The physical effects of upstream flow obstructions such
as vegetation on cross-ventilation phenomena of a building are
important for issues such as indoor thermal comfort. Modelling such
effects in Computational Fluid Dynamics simulations may also be
challenging. The aim of this work is to establish the cross-ventilation
jet behaviour in such complex terrain conditions as well as to provide
guidelines on the implementation of CFD numerical simulations in
order to model complex terrain features such as vegetation in an
efficient manner. The methodology consists of onsite measurements
on a test cell coupled with numerical simulations. It was found
that the cross-ventilation flow is highly turbulent despite the very
low velocities encountered internally within the test cells. While no
direct measurement of the jet direction was made, the measurements
indicate that flow tends to be reversed from the leeward to the
windward side. Modelling such a phenomenon proves challenging
and is strongly influenced by how vegetation is modelled. A solid
vegetation tends to predict better the direction and magnitude of the
flow than a porous vegetation approach. A simplified terrain model
was also shown to provide good comparisons with observation. The
findings have important implications on the study of cross-ventilation
in complex terrain conditions since the flow direction does not remain
trivial, as with the traditional isolated building case.
Abstract: This paper applies to the creation of virtual 3D environments for the study and development of mobile robot image based navigation algorithms and techniques, which need to operate robustly and efficiently. The test of these algorithms can be performed in a physical way, from conducting experiments on a prototype, or by numerical simulations. Current simulation platforms for robotic applications do not have flexible and updated models for image rendering, being unable to reproduce complex light effects and materials. Thus, it is necessary to create a test platform that integrates sophisticated simulated applications of real environments for navigation, with data and image processing. This work proposes the development of a high-level platform for building 3D model’s environments and the test of image-based navigation algorithms for mobile robots. Techniques were used for applying texture and lighting effects in order to accurately represent the generation of rendered images regarding the real world version. The application will integrate image processing scripts, trajectory control, dynamic modeling and simulation techniques for physics representation and picture rendering with the open source 3D creation suite - Blender.
Abstract: In this study, a spatial wavelet-based crack localization technique for a thick beam is presented. Wavelet scale in spatial wavelet transformation is optimized to enhance crack detection sensitivity. A windowing function is also employed to erase the edge effect of the wavelet transformation, which enables the method to detect and localize cracks near the beam/measurement boundaries. Theoretical model and vibration analysis considering the crack effect are first proposed and performed in MATLAB based on the Timoshenko beam model. Gabor wavelet family is applied to the beam vibration mode shapes derived from the theoretical beam model to magnify the crack effect so as to locate the crack. Relative wavelet coefficient is obtained for sensitivity analysis by comparing the coefficient values at different positions of the beam with the lowest value in the intact area of the beam. Afterward, the optimal wavelet scale corresponding to the highest relative wavelet coefficient at the crack position is obtained for each vibration mode, through numerical simulations. The same procedure is performed for cracks with different sizes and positions in order to find the optimal scale range for the Gabor wavelet family. Finally, Hanning window is applied to different vibration mode shapes in order to overcome the edge effect problem of wavelet transformation and its effect on the localization of crack close to the measurement boundaries. Comparison of the wavelet coefficients distribution of windowed and initial mode shapes demonstrates that window function eases the identification of the cracks close to the boundaries.
Abstract: The motion of an axially moving beam with rotating prismatic joint with a tip mass on the end is analyzed to investigate the nonlinear vibration and dynamic stability of the beam. The beam is moving with a harmonic axially and rotating velocity about a constant mean velocity. A time-dependent partial differential equation and boundary conditions with the aid of the Hamilton principle are derived to describe the beam lateral deflection. After the partial differential equation is discretized by the Galerkin method, the method of multiple scales is applied to obtain analytical solutions. Frequency response curves are plotted for the super harmonic resonances of the first and the second modes. The effects of non-linear term and mean velocity are investigated on the steady state response of the axially moving beam. The results are validated with numerical simulations.
Abstract: In this work, the hemodynamics in the sinuses of
Valsalva after Transcatheter Aortic Valve Implantation is numerically
examined. We focus on the physical results in the two-dimensional
case. We use a finite element methodology based on a Lagrange
multiplier technique that enables to couple the dynamics of blood
flow and the leaflets’ movement. A massively parallel implementation
of a monolithic and fully implicit solver allows more accuracy and
significant computational savings. The elastic properties of the aortic
valve are disregarded, and the numerical computations are performed
under physiologically correct pressure loads. Computational results
depict that blood flow may be subject to stagnation in the lower
domain of the sinuses of Valsalva after Transcatheter Aortic Valve
Implantation.
Abstract: In this paper, we present a simple effective numerical geometric method to estimate the divergence of a vector field over a curved surface. The conservation law is an important principle in physics and mathematics. However, many well-known numerical methods for solving diffusion equations do not obey conservation laws. Our presented method in this paper combines the divergence theorem with a generalized finite difference method and obeys the conservation law on discrete closed surfaces. We use the similar method to solve the Cahn-Hilliard equations on evolving spherical surfaces and observe stability results in our numerical simulations.
Abstract: The effect of the shape of the vessel bottom and the length of baffles on the velocity distributions in a turbulent and in a transitional flow has been simulated. The turbulent flow was simulated using standard k-ε model and simulation was verified using LES whereas transitional flow was simulated using only LES. It has been found that both the shape of tank bottom and the baffles’ length has significant effect on the flow pattern and velocity distribution below the impeller. In the dished bottom tank with baffles reaching the edge of the dish, the large rotating volume of liquid was formed below the impeller. Liquid in this rotating region was not fully mixing. A dead zone was formed here. The size and the intensity of circulation within this zone calculated by k-ε model and LES were practically identical what reinforces the accuracy of the numerical simulations. Both types of simulations also show that employing full-length baffles can reduce the size of dead zone formed below the impeller. The LES was also used to simulate the velocity distribution below the impeller in transitional flow and it has been found that secondary circulation loops were formed near the tank bottom in all investigated geometries. However, in this case the length of baffles has smaller effect on the volume of rotating liquid than in the turbulent flow.
Abstract: Stability and performance of steel plates are characterized by geometrical buckling and material yielding. In this paper, the geometrical buckling and material yielding behaviors of low yield point (LYP) steel plates are studied from the point of view of their application in steel plate shear wall (SPSW) systems. Use of LYP steel facilitates the design and application of web plates with improved buckling and energy absorption capacities in SPSW systems. LYP steel infill plates may yield first and then undergo inelastic buckling. Hence, accurate determination of the limiting plate thickness corresponding to simultaneous buckling and yielding can be effective in seismic design of such lateral force-resisting and energy dissipating systems. The limiting thicknesses of plates with different loading and support conditions are determined theoretically and verified through detailed numerical simulations. Effects of use of LYP steel and plate aspect ratio parameter on the limiting plate thickness are investigated as well. In addition, detailed studies are performed on determination of the limiting web-plate thickness in code-designed SPSWs. Some practical recommendations are accordingly provided for efficient seismic design of SPSW systems with LYP steel infill plates.
Abstract: Propagation of fire through a non-air conditioned
railway compartment is studied by virtue of numerical simulations.
Simultaneous computational fire dynamics equations, such as
Navier-Stokes, lumped species continuity, overall mass and energy
conservation, and heat transfer are solved using finite volume based
(for radiation) and finite difference based (for all other equations)
solver, Fire Dynamics Simulator (FDS). A single coupe with an eight
berth occupancy is used to establish the numerical model, followed
by the selection of a three coupe system as the fundamental unit
of the locomotive compartment. Heat Release Rate Per Unit Area
(HRRPUA) of the initial fire is varied to consider a wide range of
compartmental fires. Parameters, such as air inlet velocity relative
to the locomotive at the windows, the level of interaction with the
ambiance and closure of middle berth are studied through a wide
range of numerical simulations. Almost all the loss of lives and
properties due to fire breakout can be attributed to the direct or
indirect exposure to flames or to the inhalation of toxic gases and
resultant suffocation due to smoke and soot. Therefore, the temporal
stature of fire and smoke are reported for each of the considered
cases which can be used in the present or extended form to develop
guidelines to be followed in case of a fire breakout.
Abstract: Punching shear failure is usually the governing failure mode of flat plate structures. Punching failure is brittle in nature which induces more vulnerability to this type of structure. In the present study, a 3D finite element model of a flat plate with low reinforcement ratio and without any transverse reinforcement has been developed. Punching shear stress and the deflection data were obtained on the surface of the flat plate as well as through the thickness of the model from numerical simulations. The obtained data were compared with the experimental results. Variation of punching stress with respect to deflection as obtained from numerical results is found to be in good agreement with the experimental results; the range of variation of punching stress is within 5%. The numerical simulation shows an early and gradual onset of nonlinearity, whereas the same is late and abrupt as observed in the experimental results. The range of variation of punching stress for different slab thicknesses between experimental and numerical results is less than 15%. The developed numerical model is useful to complement available punching test series performed in the past. The results obtained from the numerical model will be helpful for designing retrofitting schemes of flat plates.
Abstract: The numerical simulation based on the Finite Element Method (FEM) is widely used in academic institutes and in the industry. It is a useful tool to predict many phenomena present in the classical manufacturing forming processes such as fracture. But, the results of such numerical model depend strongly on the parameters of the constitutive behavior model. The influences of thermal and mechanical loads cause damage. The temperature and strain rate dependent materials’ properties and their modelling are discussed. A Johnson-Cook Model of damage has been selected for the numerical simulations. Virtual software called the ABAQUS 6.11 is used for finite element analysis. This model was introduced in order to give information concerning crack initiation during thermal and mechanical loads.
Abstract: Optimizations of Plate Heat Exchangers (PHS) have received great attention in the past decade. In this study, heat transfer and pressure drop coefficients are compared for rectangular and circular PHS employing numerical simulations. Plates are designed to have equivalent areas. Simulations were implemented to investigate the efficiency of PHSs considering heat transfer, friction factor and pressure drop. Amount of heat transfer and pressure drop was obtained for different range of Reynolds numbers. These two parameters were compared with aim of F "weighting factor correlation". In this comparison, the minimum amount of F indicates higher efficiency. Results reveal that the F value for rectangular shape is less than circular plate, and hence using rectangular shape of PHS is more efficient than circular one. It was observed that, the amount of friction factor is correlated to the Reynolds numbers, such that friction factor decreased in both rectangular and circular plates with an increase in Reynolds number. Furthermore, such simulations revealed that the amount of heat transfer in rectangular plate is more than circular plate for different range of Reynolds numbers. The difference is more distinct for higher Reynolds number. However, amount of pressure drop in circular plate is less than rectangular plate for the same range of Reynolds numbers which is considered as a negative point for rectangular plate efficiency. It can be concluded that, while rectangular PHSs occupy more space than circular plate, the efficiency of rectangular plate is higher.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: The objective of the paper is a numerical study of heat
transfer between perforated metal plates and the surrounding air
flows. Different perforation structures can nowadays be found in
various industrial products. Besides improving the mechanical
properties, the perforations can intensify the heat transfer as well. The
heat transfer coefficient depends on a wide range of parameters such
as type of perforation, size, shape, flow properties of the surrounding
air etc. The paper was focused on three different perforation
structures which have been investigated from the point of the view of
the production in the previous studies. To determine the heat
coefficients and the Nusselt numbers, the numerical simulation
approach was adopted. The calculations were performed using the
OpenFOAM software. The three-dimensional, unstable, turbulent and
incompressible air flow around the perforated surface metal plate was
considered.