Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Laser Profiler (LP) data from aerial laser surveys have
been increasingly used as topographical inputs to numerical
simulations of flooding and inundation in river basins. LP data has
great potential for reproducing topography, but its effective usage has
not yet been fully established. In this study, flooding and inundation
are simulated numerically using LP data for the Jobaru River basin of
Japan’s Saga Plain. The analysis shows that the topography is
reproduced satisfactorily in the computational domain with urban and
agricultural areas requiring different grid sizes. A 2-D numerical
simulation shows that flood flow behavior changes as grid size is
varied.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: This paper presents a CFD analysis of the flow field
around a thin flat plate of infinite span inclined at 90° to a fluid
stream of infinite extent. Numerical predictions have been compared
to experimental measurements, in order to assess the potential of the
finite volume code of determining the aerodynamic forces acting on a
bluff body invested by a fluid stream of infinite extent.
Several turbulence models and spatial node distributions have
been tested. Flow field characteristics in the neighborhood of the flat
plate have been investigated, allowing the development of a
preliminary procedure to be used as guidance in selecting the
appropriate grid configuration and the corresponding turbulence
model for the prediction of the flow field over a two-dimensional
vertical flat plate.
Abstract: In this paper, numerical simulation is used to
investigate the thermal performance of liquid cooling heatsink with
microchannels due to geometric arrangement. Commercial software
ICEPAK is utilized for the analysis. The considered parameters
include aspect ratio, porosity and the length and height of
microchannel. The aspect ratio varies from 3 to 16 and the length of
microchannel is 10mm, 14mm, and 18mm. The height of
microchannel is 2mm, 3mm and 4mm. It is found short channel have
better thermal efficiency than long channel at 490Pa. No matter the
length of channel the best aspect ratio is 4. It is also noted that pressure
difference at 2940Pa the best aspect ratio from 4 to 8, it means pressure
difference affect aspect ratio, effective thermal resistance at low
pressure difference but lower effective thermal resistance at high
pressure difference.
Abstract: Clean air in subway station is important to passengers. The Platform Screen Doors (PSDs) can improve indoor air quality in the subway station; however the air quality in the subway tunnel is degraded. The subway tunnel has high CO2 concentration and indoor particulate matter (PM) value. The Indoor Air Quality (IAQ) level in subway environment degrades by increasing the frequency of the train operation and the number of the train. The ventilation systems of the subway tunnel need improvements to have better air-quality. Numerical analyses might be effective tools to analyze the performance of subway twin-track tunnel ventilation systems. An existing subway twin-track tunnel in the metropolitan Seoul subway system is chosen for the numerical simulations. The ANSYS CFX software is used for unsteady computations of the airflow inside the twin-track tunnel when the train moves. The airflow inside the tunnel is simulated when one train runs and two trains run at the same time in the tunnel. The piston-effect inside the tunnel is analyzed when all shafts function as the natural ventilation shaft. The supplied air through the shafts is mixed with the pollutant air in the tunnel. The pollutant air is exhausted by the mechanical ventilation shafts. The supplied and discharged airs are balanced when only one train runs in the twin-track tunnel. The pollutant air in the tunnel is high when two trains run simultaneously in opposite direction and all shafts functioned as the natural shaft cases when there are no electrical power supplies in the shafts. The remained pollutant air inside the tunnel enters into the station platform when the doors are opened.
Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: The radiative exchange method is introduced as a
numerical method for the simulation of radiative heat transfer in an
absorbing, emitting and isotropically scattering media. In this
method, the integro-differential radiative balance equation is solved
by using a new introduced concept for the exchange factor. Even
though the radiative source term is calculated in a mesh structure that
is coarser than the structure used in computational fluid dynamics,
calculating the exchange factor between different coarse elements by
using differential integration elements makes the result of the method
close to that of integro-differential radiative equation. A set of
equations for calculating exchange factors in two and threedimensional
Cartesian coordinate system is presented, and the
method is used in the simulation of radiative heat transfer in twodimensional
rectangular case and a three-dimensional simple cube.
The result of using this method in simulating different cases is
verified by comparing them with those of using other numerical
radiative models.
Abstract: Based on experimental data using accelerometry technology there was developed an analytical model that approximates human induced ground reaction forces in vertical, longitudinal and lateral directions ascending and descending the stairs. Proposed dynamic loading factors and corresponding phase shifts for the first five harmonics of continuous walking force history in case of stair ascend and descend. Into account is taken imperfectness of individual footfall forcing functions, differences between continuous walking force histories among individuals. There is proposed mean synthetic continuous walking force history that can be used in numerical simulations of human movement on the stairs.
Abstract: This work proposes a novel market-based air traffic flow control model considering competitive airlines in air traffic network. In the flow model, an agent based framework for resources (link/time pair) pricing is described. Resource agent and auctioneer for groups of resources are also introduced to simulate the flow management in Air Traffic Control (ATC). Secondly, the distributed group pricing algorithm is introduced, which efficiently reflect the competitive nature of the airline industry. Resources in the system are grouped according to the degree of interaction, and each auctioneer adjust s the price of one group of resources respectively until the excess demand of resources becomes zero when the demand and supply of resources of the system changes. Numerical simulation results show the feasibility of solving the air traffic flow control problem using market mechanism and pricing algorithms on the air traffic network.
Abstract: For stable bipedal gait generation on the level floor,
efficient restoring of mechanical energy lost by heel collision at
the ground is necessary. Parametric excitation principle is one of
the solutions. We dealt with the robot-s total center of mass as
an inverted pendulum to consider the total dynamics of the robot.
Parametrically excited walking requires the use of continuous target
trajectory that is close to discontinuous optimal trajectory. In this
paper, we proposed the new target trajectory based on a position
in the walking direction. We surveyed relations between walking
performance and the parameters that form the target trajectory via
numerical simulations. As a result, it was found that our target
trajectory has the similar characteristics of a parametrically excited
inverted pendulum.
Abstract: In this paper, the modified optimal sliding mode control with a proposed method to design a sliding surface is presented. Because of the inability of the previous approach of the sliding mode method to design a bounded and suitable input, the new variation is proposed in the sliding manifold to obviate problems in a structural system. Although the sliding mode control is a powerful method to reject disturbances and noises, the chattering problem is not good for actuators. To decrease the chattering phenomena, the optimal control is added to the sliding mode control. Not only the proposed method can decline the intense variations in the inputs of the system but also it can produce the efficient responses respect to the sliding mode control and optimal control that are shown by performing some numerical simulations.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: The Eulerian numerical method is proposed to analyze
the explosion in tunnel. Based on this method, an original software
M-MMIC2D is developed by Cµ program language. With this
software, the explosion problem in the tunnel with three
expansion-chambers is numerically simulated, and the results are
found to be in full agreement with the observed experimental data.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: Computational study of two dimensional supersonic reacting hydrogen-air flows is performed to investigate the nitrogen effects on ignition delay time for premixed and diffusion flames. Chemical reaction is treated using detail kinetics and the advection upstream splitting method is used to calculate the numerical inviscid fluxes. The results show that just in stoichiometric condition for both premixed and diffusion flames, there is monotone dependency of the ignition delay time to the nitrogen addition. In other situations, the optimal condition from ignition viewpoint should be found using numerical investigations.