Abstract: In present study, an approach is adopted where photovoltaic thermal flat plate collector is integrated with compound parabolic concentrator. Analytical expression of temperature dependent electrical efficiency of N number of partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) water collector connected in series has been derived with the help of basic thermal energy balance equations. Analysis has been carried for winter weather condition at Delhi location, India. Energy and exergy performance of N - partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) Water collector system has been compared for two cases: (i) 25% area of water collector covered by PV module, (ii) 75% area of water collector covered by PV module. It is observed that case (i) has been best suited for thermal performance and case (ii) for electrical energy as well as overall exergy.
Abstract: The separation of Hg (II) from produced water by
hollow fiber contactors (HFC) was investigation. This system
included of two hollow fiber modules in the series connecting. The
first module used for the extraction reaction and the second module
for stripping reaction. Aliquat336 extractant was fed from the organic
reservoirs into the shell side of the first hollow fiber module and
continuous to the shell side of the second module. The organic liquid
was continuously feed recirculate and back to the reservoirs. The feed
solution was pumped into the lumen (tube side) of the first hollow
fiber module. Simultaneously, the stripping solution was pumped in
the same way in tube side of the second module. The feed and
stripping solution was fed which had a countercurrent flow. Samples
were kept in the outlet of feed and stripping solution at 1 hour and
characterized concentration of Hg (II) by Inductively Couple Plasma
Atomic Emission Spectroscopy (ICP-AES). Feed solution was
produced water from natural gulf of Thailand. The extractant was
Aliquat336 dissolved in kerosene diluent. Stripping solution used was
nitric acid (HNO3) and thiourea (NH2CSNH2). The effect of carrier
concentration and type of stripping solution were investigated.
Results showed that the best condition were 10 % (v/v) Aliquat336
and 1.0 M NH2CSNH2. At the optimum condition, the extraction and
stripping of Hg (II) were 98% and 44.2%, respectively.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: Structured Query Language (SQL) is the standard de facto language to access and manipulate data in a relational database. Although SQL is a language that is simple and powerful, most novice users will have trouble with SQL syntax. Thus, we are presenting SQL generator tool which is capable of translating actions and displaying SQL commands and data sets simultaneously. The tool was developed based on Model-View-Controller (MVC) pattern. The MVC pattern is a widely used software design pattern that enforces the separation between the input, processing, and output of an application. Developers take full advantage of it to reduce the complexity in architectural design and to increase flexibility and reuse of code. In addition, we use White-Box testing for the code verification in the Model module.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: This work presents the modelling and simulation of
saponification of ethyl acetate in the presence of sodium hydroxide in
a plug flow reactor using Aspen Plus simulation software. Plug flow
reactors are widely used in the industry due to the non-mixing
property. The use of plug flow reactors becomes significant when
there is a need for continuous large scale reaction or fast reaction.
Plug flow reactors have a high volumetric unit conversion as the
occurrence for side reactions is minimum. In this research Aspen Plus
V8.0 has been successfully used to simulate the plug flow reactor. In
order to simulate the process as accurately as possible HYSYS Peng-
Robinson EOS package was used as the property method. The results
obtained from the simulation were verified by the experiment carried
out in the EDIBON plug flow reactor module. The correlation
coefficient (r2) was 0.98 and it proved that simulation results
satisfactorily fit for the experimental model. The developed model
can be used as a guide for understanding the reaction kinetics of a
plug flow reactor.
Abstract: A polypropylene hollow fiber membrane module is used for separating dissolved gases which contain dissolved oxygen from water. These dissolved gases can be used for underwater breathing. To be used for a human, the minimum amount of oxygen is essential. To increase separation of dissolved gases, much water and high surface area of hollow fibers are requested. For efficient separation system, performance of single membrane module with high surface area needs to be investigated.
In this study, we set up experimental devices for analyzing separation characteristics of dissolved gases including oxygen from water using a polypropylene hollow fiber membrane module. Separation of dissolved gases from water is investigated with variations of water flow rates. Composition of dissolved gases is also measured using GC. These results expect to be used in developing the portable separation system.
Abstract: Multilevel inverter is a promising inverter topology for high voltage and high power applications. This inverter synthesizes several different levels of DC voltages to produce a stepped AC output that approaches the pure sine waveform. The three different topologies, diode-clamped inverter, capacitor-clamped inverter and cascaded h-bridge multilevel inverter are widely used in these multilevel inverters. Among the three topologies, cascaded h-bridge multilevel inverter is more suitable for photovoltaic applications since each PV array can act as a separate dc source for each h-bridge module. This research especially focus on photovoltaic power source as input to the system and shows the potential of a Single Phase Cascaded H-bridge Eleven level inverter governed by the fuzzy logic controller to improve the power quality by reducing the total harmonic distortion at the output voltage. Hence the efficiency of the system will be improved. Simulation using MATLAB/SIMULINK has been done to verify the performance of cascaded h-bridge eleven level inverter using sinusoidal pulse width modulation technique. The simulated output shows very favorable result.
Abstract: This paper discusses a software application to aid in the smooth functioning of a university internship program, including a student, faculty and an administration module. The software can also calculate the most apt combination of students to stations and allocate them respectively.
Abstract: We introduced the notions of (1, k)-prime ideal and (1, k)-jointly prime (R, S)-submodule as a generalization of prime ideal and jointly prime (R, S)-submodule, respectively. We provide a relationship between (1, k)-prime ideal and (1, k)-jointly prime (R, S)-submodule. Characterizations of (1, k)-jointly prime (R, S)- submodules are also given.
Abstract: This paper describes the development of a fully
automated measurement software for antenna radiation pattern
measurements in a Compact Antenna Test Range (CATR). The
CATR has a frequency range from 2-40 GHz and the measurement
hardware includes a Network Analyzer for transmitting and
Receiving the microwave signal and a Positioner controller to control
the motion of the Styrofoam column. The measurement process
includes Calibration of CATR with a Standard Gain Horn (SGH)
antenna followed by Gain versus angle measurement of the Antenna
under test (AUT). The software is designed to control a variety of
microwave transmitter / receiver and two axis Positioner controllers
through the standard General Purpose interface bus (GPIB) interface.
Addition of new Network Analyzers is supported through a slight
modification of hardware control module. Time-domain gating is
implemented to remove the unwanted signals and get the isolated
response of AUT. The gated response of the AUT is compared with
the calibration data in the frequency domain to obtain the desired
results. The data acquisition and processing is implemented in
Agilent VEE and Matlab. A variety of experimental measurements
with SGH antennas were performed to validate the accuracy of
software. A comparison of results with existing commercial
softwares is presented and the measured results are found to be
within .2 dBm.
Abstract: Since Network-on-Chip (NoC) uses network
interfaces (NIs) to improve the design productivity, by now, there
have been a few papers addressing the design and implementation of a
NI module. However, none of them considered the difference of
address encoding methods between NoC and the traditional
bus-shared architecture. On the basis of this difference, in the paper,
we introduce a transmit mechanism to solve such a problem for global
asynchronous locally synchronous (GALS) NoC. Furthermore, we
give the concrete implementation of the NI module in this transmit
mechanism. Finally, we evaluate its performance and area overhead
by a VHDL-based cycle-accurate RTL model and simulation results
confirm the validity of this address-oriented transmit mechanism.
Abstract: Brain Computer Interface (BCI) has been recently
increased in research. Functional Near Infrared Spectroscope (fNIRs)
is one the latest technologies which utilize light in the near-infrared
range to determine brain activities. Because near infrared technology
allows design of safe, portable, wearable, non-invasive and wireless
qualities monitoring systems, fNIRs monitoring of brain
hemodynamics can be value in helping to understand brain tasks. In
this paper, we present results of fNIRs signal analysis indicating that
there exist distinct patterns of hemodynamic responses which
recognize brain tasks toward developing a BCI. We applied two
different mathematics tools separately, Wavelets analysis for
preprocessing as signal filters and feature extractions and Neural
networks for cognition brain tasks as a classification module. We
also discuss and compare with other methods while our proposals
perform better with an average accuracy of 99.9% for classification.
Abstract: Biclustering is a very useful data mining technique for
identifying patterns where different genes are co-related based on a
subset of conditions in gene expression analysis. Association rules
mining is an efficient approach to achieve biclustering as in
BIMODULE algorithm but it is sensitive to the value given to its
input parameters and the discretization procedure used in the
preprocessing step, also when noise is present, classical association
rules miners discover multiple small fragments of the true bicluster,
but miss the true bicluster itself. This paper formally presents a
generalized noise tolerant bicluster model, termed as μBicluster. An
iterative algorithm termed as BIDENS based on the proposed model
is introduced that can discover a set of k possibly overlapping
biclusters simultaneously. Our model uses a more flexible method to
partition the dimensions to preserve meaningful and significant
biclusters. The proposed algorithm allows discovering biclusters that
hard to be discovered by BIMODULE. Experimental study on yeast,
human gene expression data and several artificial datasets shows that
our algorithm offers substantial improvements over several
previously proposed biclustering algorithms.
Abstract: A strategy is implemented to find the improved configuration design of an existing aircraft structure by executing topology and shape optimizations. Structural analysis of the Initial Design Space is performed in ANSYS under the loads pertinent to operating and ground conditions. By using the FEA results and data, an initial optimized layout configuration is attained by exploiting nonparametric topology optimization in TOSCA software. Topological optimized surfaces are then smoothened and imported in ANSYS to develop the geometrical features. Nodes at the critical locations of resulting voids are selected for sketching rough profiles. Rough profiles are further refined and CAD feasible geometric features are generated. The modified model is then analyzed under the same loadings and constraints as defined for topology optimization. Shape at the peak stress concentration areas are further optimized by exploiting the shape optimization in TOSCA.shape module. The harmonized stressed model with the modified surfaces is then imported in CATIA to develop the final design.
Abstract: The paper researched and presented a virtual simulation system based on a full-digital lunar terrain, integrated with kinematics and dynamics module as well as autonomous navigation simulation module. The system simulation models are established. Enabling technologies such as digital lunar surface module, kinematics and dynamics simulation, Autonomous navigation are investigated. A prototype system for lunar rover locomotion simulation is developed based on these technologies. Autonomous navigation is a key echnology in lunar rover system, but rarely involved in virtual simulation system. An autonomous navigation simulation module have been integrated in this prototype system, which was proved by the simulation results that the synthetic simulation and visualizing analysis system are established in the system, and the system can provide efficient support for research on the autonomous navigation of lunar rover.
Abstract: Recently, much research has been conducted for
security for wireless sensor networks and ubiquitous computing.
Security issues such as authentication and data integrity are major
requirements to construct sensor network systems. Advanced
Encryption Standard (AES) is considered as one of candidate
algorithms for data encryption in wireless sensor networks. In this
paper, we will present the hardware architecture to implement low
power AES crypto module. Our low power AES crypto module has
optimized architecture of data encryption unit and key schedule unit
which could be applicable to wireless sensor networks. We also details
low power design methods used to design our low power AES crypto
module.
Abstract: Malaysia government had been trying hard in order to
find the most efficient methods in learning. However, it is hard to
actually access and evaluate students whom will then be called an
excellent student. It is because in our realties student who excellent
is only excel in academic. This evaluation becomes a problem
because it not balances in our real life interm of to get an excellent
student in whole area in their involvement of curiculum and cocuriculum.
To overcome this scenario, we designed a module for
Student Idol to evaluate student through three categories which are
academic, co-curiculum and leadership. All the categories have their
own merit point. Using this method, student will be evaluated more
accurate compared to the previously. So, teacher can easily evaluate
their student without having any emotion factor, relation factor and
others. As conclusion this system module will helps the development
of student evaluation more accurate and valid in Student Idol.
Abstract: This paper presents a rule-based text- to- speech
(TTS) Synthesis System for Standard Malay, namely SMaTTS. The
proposed system using sinusoidal method and some pre- recorded
wave files in generating speech for the system. The use of phone
database significantly decreases the amount of computer memory
space used, thus making the system very light and embeddable. The
overall system was comprised of two phases the Natural Language
Processing (NLP) that consisted of the high-level processing of text
analysis, phonetic analysis, text normalization and morphophonemic
module. The module was designed specially for SM to overcome
few problems in defining the rules for SM orthography system before
it can be passed to the DSP module. The second phase is the Digital
Signal Processing (DSP) which operated on the low-level process of
the speech waveform generation. A developed an intelligible and
adequately natural sounding formant-based speech synthesis system
with a light and user-friendly Graphical User Interface (GUI) is
introduced. A Standard Malay Language (SM) phoneme set and an
inclusive set of phone database have been constructed carefully for
this phone-based speech synthesizer. By applying the generative
phonology, a comprehensive letter-to-sound (LTS) rules and a
pronunciation lexicon have been invented for SMaTTS. As for the
evaluation tests, a set of Diagnostic Rhyme Test (DRT) word list was
compiled and several experiments have been performed to evaluate
the quality of the synthesized speech by analyzing the Mean Opinion
Score (MOS) obtained. The overall performance of the system as
well as the room for improvements was thoroughly discussed.
Abstract: This paper proposes a novel multi-format stream grid
architecture for real-time image monitoring system. The system, based
on a three-tier architecture, includes stream receiving unit, stream
processor unit, and presentation unit. It is a distributed computing and
a loose coupling architecture. The benefit is the amount of required
servers can be adjusted depending on the loading of the image
monitoring system. The stream receive unit supports multi capture
source devices and multi-format stream compress encoder. Stream
processor unit includes three modules; they are stream clipping
module, image processing module and image management module.
Presentation unit can display image data on several different platforms.
We verified the proposed grid architecture with an actual test of image
monitoring. We used a fast image matching method with the
adjustable parameters for different monitoring situations. Background
subtraction method is also implemented in the system. Experimental
results showed that the proposed architecture is robust, adaptive, and
powerful in the image monitoring system.