Abstract: Mixed Model Production is the practice of assembling
several distinct and different models of a product on the same
assembly line without changeovers and then sequencing those models
in a way that smoothes the demand for upstream components. In this
paper, we consider an objective function which minimizes total
stoppage time and total idle time and it is presented sequence
dependent set up time. Many studies have been done on the mixed
model assembly lines. But in this paper we specifically focused on
reducing the idle times. This is possible through various help policies.
For improving the solutions, some cases developed and about 40 tests
problem was considered. We use scatter search for optimization and
for showing the efficiency of our algorithm, experimental results
shows behavior of method. Scatter search and help policies can
produce high quality answers, so it has been used in this paper.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: The motivation for adaptive modulation and coding is
to adjust the method of transmission to ensure that the maximum
efficiency is achieved over the link at all times. The receiver
estimates the channel quality and reports it back to the transmitter.
The transmitter then maps the reported quality into a link mode. This
mapping however, is not a one-to-one mapping. In this paper we
investigate a method for selecting the proper modulation scheme.
This method can dynamically adapt the mapping of the Signal-to-
Noise Ratio (SNR) into a link mode. It enables the use of the right
modulation scheme irrespective of changes in the channel conditions
by incorporating errors in the received data. We propose a Markov
model for this method, and use it to derive the average switching
thresholds and the average throughput. We show that the average
throughput of this method outperforms the conventional threshold
method.
Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: Data compression is used operationally to reduce bandwidth and storage requirements. An efficient method for achieving lossless weather radar data compression is presented. The characteristics of the data are taken into account and the optical linear prediction is used for the PPI images in the weather radar data in the proposed method. The next PPI image is identical to the current one and a dramatic reduction in source entropy is achieved by using the prediction algorithm. Some lossless compression methods are used to compress the predicted data. Experimental results show that for the weather radar data, the method proposed in this paper outperforms the other methods.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: Using the animations video of teaching materials is an
effective learning method. However, we thought that more effective learning method is to produce the teaching video by learners
themselves. The learners who act as the producer must learn and understand well to produce and present video of teaching materials to
others. The purpose of this study is to propose the project based learning (PBL) technique by co-producing video of IT (information
technology) teaching materials. We used the T2V player to produce
the video based on TVML a TV program description language. By
proposed method, we have assigned the learners to produce the
animations video for “National Examination for Information
Processing Technicians (IPA examination)" in Japan, in order to get
them learns various knowledge and skill on IT field. Experimental
result showed that learning effect has occurred at the video production
process that useful for IT personnel resources development.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: One of the disadvantages of using OFDM is the larger
peak to averaged power ratio (PAPR) in its time domain signal. The
larger PAPR signal would course the fatal degradation of bit error
rate performance (BER) due to the inter-modulation noise in the nonlinear
channel. This paper proposes an improved DSI (Dummy
Sequence Insertion) method, which can achieve the better PAPR and
BER performances. The feature of proposed method is to optimize
the phase of each dummy sub-carrier so as to reduce the PAPR
performance by changing all predetermined phase coefficients in the
time domain signal, which is calculated for data sub-carriers and
dummy sub-carriers separately. To achieve the better PAPR
performance, this paper also proposes to employ the time-frequency
domain swapping algorithm for fine adjustment of phase coefficient
of the dummy subcarriers, which can achieve the less complexity of
processing and achieves the better PAPR and BER performances
than those for the conventional DSI method. This paper presents
various computer simulation results to verify the effectiveness of
proposed method as comparing with the conventional methods in the
non-linear channel.
Abstract: This paper at first presents approximate analytical
solutions for systems of fractional differential equations using the
differential transform method. The application of differential
transform method, developed for differential equations of integer
order, is extended to derive approximate analytical solutions of
systems of fractional differential equations. The solutions of our
model equations are calculated in the form of convergent series with
easily computable components. After that a drive-response
synchronization method with linear output error feedback is
presented for “generalized projective synchronization" for a class of
fractional-order chaotic systems via a scalar transmitted signal.
Genesio_Tesi and Duffing systems are used to illustrate the
effectiveness of the proposed synchronization method.
Abstract: The goal of this work is to describe a new algorithm for finding the optimal variable order, number of nodes for any order and other ROBDD parameters, based on a tabular method. The tabular method makes use of a pre-built backend database table that stores the ROBDD size for selected combinations of min-terms. The user uses the backend table and the proposed algorithm to find the necessary ROBDD parameters, such as best variable order, number of nodes etc. Experimental results on benchmarks are given for this technique.
Abstract: For the first time since 1940 and presentation of
theodorson-s theory, distribution of thrust, torque and efficiency
along the blade of a counter rotating propeller axial fan was studied
with a novel method in this research. A constant chord, constant
pitch symmetric fan was investigated with Reynolds Stress
Turbulence method in this project and H.E.S. method was utilized to
obtain distribution profiles from C.F.D. tests outcome. C.F.D. test
results were validated by estimation from Playlic-s analytical method.
Final results proved ability of H.E.S. method to obtain distribution
profiles from C.F.D test results and demonstrated interesting facts
about effects of solidity and differences between distributions in front
and rear section.
Abstract: The paper deals with the comparison study of
harmonic detection methods for a shunt active power filter. The
%THD and the power factor value at the PCC point after
compensation are considered for the comparison. There are three
harmonic detection methods used in the paper that are synchronous
reference frame method, synchronous detection method, and DQ axis
with Fourier method. In addition, the ideal current source is used to
represent the active power filter by assuming an infinitely fast
controller action of the active power filter. The simulation results
show that the DQ axis with Fourier method provides the minimum
%THD after compensation compared with other methods. However,
the power factor value at the PCC point after compensation is slightly
lower than that of synchronous detection method.
Abstract: The research focuses on the effects of polyphenols
extracted from Sambucus nigra fruit, using an experimental arterial
hypertension pattern, as well as their influence on the oxidative
stress. The results reveal the normalization of the reduced glutathion
concentration, as well as a considerable reduction in the
malondialdehide serum concentration by the polyphenolic protection.
The rat blood pressure values were recorded using a CODATM
system, which uses a non-invasive blood pressure measuring method.
All the measured blood pressure components revealed a biostatistically
significant (p
Abstract: In this paper, we propose a method of alter duration in
frequency domain that control prosody in real time after pitch
alteration. If there has a method to alteration duration freely among
prosody information, that may used in several fields such as speech
impediment person's pronunciation proof reading or language study.
The pitch alteration method used control prosody altered by PSOLA
synthesis method which is in time domain processing method.
However, the duration of pitch alteration speech is changed by the
frequency domain. In this paper, we altered the duration with the
method of duration alteration by Fast Fourier Transformation in
frequency domain. Consequently, the intelligibility of the pitch and
duration are controlled has a slight decrease than the case when only
pitch is changed, but the proposed algorithm obtained the higher MOS
score about naturalness.
Abstract: As the electrical power industry is restructured, the electrical power exchange is becoming extended. One of the key information used to determine how much power can be transferred through the network is known as available transfer capability (ATC). To calculate ATC, traditional deterministic approach is based on the severest case, but the approach has the complexity of procedure. Therefore, novel approach for ATC calculation is proposed using cost-optimization method in this paper, and is compared with well-being method and risk-benefit method. This paper proposes the optimal transfer capability of HVDC system between mainland and a separated island in Korea through these three methods. These methods will consider production cost, wheeling charge through HVDC system and outage cost with one depth (N-1 contingency)
Abstract: In this paper, mesh-free element free Galerkin (EFG) method is extended to solve two-dimensional potential flow problems. Two ideal fluid flow problems (i.e. flow over a rigid cylinder and flow over a sphere) have been formulated using variational approach. Penalty and Lagrange multiplier techniques have been utilized for the enforcement of essential boundary conditions. Four point Gauss quadrature have been used for the integration on two-dimensional domain (Ω) and nodal integration scheme has been used to enforce the essential boundary conditions on the edges (┌). The results obtained by EFG method are compared with those obtained by finite element method. The effects of scaling and penalty parameters on EFG results have also been discussed in detail.
Abstract: In this paper we propose a blind algorithm for peakto- average power ratio (PAPR) reduction in OFDM systems, based on selected mapping (SLM) algorithm as a distortionless method. The main drawback of the conventional SLM technique is the need for transmission of several side information bits, for each data block, which results in loss in data rate transmission. In the proposed method some special number of carriers in the OFDM frame is reserved to be rotated with one of the possible phases according to the number of phase sequence blocks in SLM algorithm. Reserving some limited number of carriers wont effect the reduction in PAPR of OFDM signal. Simulation results show using ML criteria at the receiver will lead to the same system-performance as the conventional SLM algorithm, while there is no need to send any side information to the receiver.
Abstract: In this paper, we propose a multiple objective optimization model with respect to portfolio selection problem for investors looking forward to diversify their equity investments in a number of equity markets. Based on Markowitz-s M-V model we developed a Fuzzy Mixed Integer Multi-Objective Nonlinear Programming Problem (FMIMONLP) to maximize the investors- future gains on equity markets, reach the optimal proportion of the budget to be invested in different equities. A numerical example with a comprehensive analysis on artificial data from several equity markets is presented in order to illustrate the proposed model and its solution method. The model performed well compared with the deterministic version of the model.