Abstract: Bond Graph as a unified multidisciplinary tool is widely
used not only for dynamic modelling but also for Fault Detection and
Isolation because of its structural and causal proprieties. A binary
Fault Signature Matrix is systematically generated but to make the
final binary decision is not always feasible because of the problems
revealed by such method. The purpose of this paper is introducing a
methodology for the improvement of the classical binary method of
decision-making, so that the unknown and identical failure signatures
can be treated to improve the robustness. This approach consists of
associating the evaluated residuals and the components reliability data
to build a Hybrid Bayesian Network. This network is used in two
distinct inference procedures: one for the continuous part and the
other for the discrete part. The continuous nodes of the network are
the prior probabilities of the components failures, which are used by
the inference procedure on the discrete part to compute the posterior
probabilities of the failures. The developed methodology is applied
to a real steam generator pilot process.
Abstract: Horseradish (Armoracia rusticana) is a perennial herb belonging to the Brassicaceae family and contains biologically active substances. The aim of the current research was to determine best method for extraction of phenolic compounds from horseradish roots showing high antiradical activity. Three genotypes (No. 105; No. 106 and variety ‘Turku’) of horseradish roots were extracted with eight different solvents: n-hexane, ethyl acetate, diethyl ether, 2-propanol, acetone, ethanol (95%), ethanol / water / acetic acid (80/20/1 v/v/v) and ethanol / water (80/20 by volume) using two extraction methods (conventional and Soxhlet). As the best solvents ethanol and ethanol / water solutions can be chosen. Although in Soxhlet extracts TPC was higher, scavenging activity of DPPH˙ radicals did not increase. It can be concluded that using Soxhlet extraction method more compounds that are not effective antioxidants.
Abstract: With increasing complexity in electronic systems
there is a need for system level anomaly detection and fault isolation.
Anomaly detection based on vector similarity to a training set is used
in this paper through two approaches, one the preserves the original
information, Mahalanobis Distance (MD), and the other that
compresses the data into its principal components, Projection Pursuit
Analysis. These methods have been used to detect deviations in
system performance from normal operation and for critical parameter
isolation in multivariate environments. The study evaluates the
detection capability of each approach on a set of test data with known
faults against a baseline set of data representative of such “healthy"
systems.
Abstract: Article devoted to the development of technologies
for medicine and agroecology by using plant organelle – spherosome.
Technological method of purification and isolation of this organelle
by using novel nanostructured carbon sorbent – “nanocarbosorb"
ARK type are presented. Also the methods of preparation of
nanocontainers based on using of spherosome with loaded isosorbide
dinitrate, piroxicam or diclofenak are exhibited. We found that the
spherosome could be applied for ecological aims as bioregulator and
also as biosensor for determination of ammonia ions in water
reservoirs at concentration range 1mM to 100mM.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Recently, there have been considerable efforts towards the convergence between P2P and Grid computing in order to reach a solution that takes the best of both worlds by exploiting the advantages that each offers. Augmenting the peer-to-peer model to the services of the Grid promises to eliminate bottlenecks and ensure greater scalability, availability, and fault-tolerance. The Grid Information Service (GIS) directly influences quality of service for grid platforms. Most of the proposed solutions for decentralizing the GIS are based on completely flat overlays. The main contributions for this paper are: the investigation of a novel resource discovery framework for Grid implementations based on a hierarchy of structured peer-to-peer overlay networks, and introducing a discovery algorithm utilizing the proposed framework. Validation of the framework-s performance is done via simulation. Experimental results show that the proposed organization has the advantage of being scalable while providing fault-isolation, effective bandwidth utilization, and hierarchical access control. In addition, it will lead to a reliable, guaranteed sub-linear search which returns results within a bounded interval of time and with a smaller amount of generated traffic within each domain.
Abstract: Considering the merits and limitations of energy dissipation system, seismic isolation system and suspension system, a new earthquake resistant system is proposed and is demonstrated numerically through a frame-core structure. Base isolators and story isolators are installed in the proposed system. The former “isolates" the frame from the foundation and the latter “separates" the frame from the center core. Equations of motion are formulated to study the response of the proposed structural system to strong earthquake motion. As compared with the fixed-base building system, the proposed structural system shows substantial reduction on structural response.
Abstract: The bioassay-guided isolation and purification of an
ethyl acetate extract of Aspergillus terreus MC751 led to the
characterization of butyrolactone I as an antidiabetic and antioxidant.
The antidiabetic activity of butyrolactone I was evaluated by α-
glucosidase and α-amylase inhibition assays. Butyrolactone I
demonstrated significant concentration-dependent, mixed-type
inhibitory activity against yeast α-glucosidase with an IC50 of 54μM.
However, the compound exhibited less activity against rat intestinal
α-glucosidase and α-amylase. This is the first report on α-glucosidase
inhibitory activity of butyrolactone I. The antioxidative activity of
butyrolactone I was evaluated based on scavenging effects on 1,1-
diphenyl-2-picrylhydrazyl (DPPH) (IC50 =51 μM) and hydrogen
peroxide (IC50= 141 μM) radicals as well as a reducing power assay.
The results suggest that butyrolactone I is a promising antidiabetic as
well as antioxidant and should be considered for clinical trials.
Abstract: Microwave energy is a superior alternative to several other thermal treatments. Extraction techniques are widely employed for the isolation of bioactive compounds and vegetable oils from oil seeds. Among the different and new available techniques, microwave pretreatment of seeds is a simple and desirable method for production of high quality vegetable oils. Microwave pretreatment for oil extraction has many advantages as follow: improving oil extraction yield and quality, direct extraction capability, lower energy consumption, faster processing time and reduced solvent levels compared with conventional methods. It allows also for better retention and availability of desirable nutraceuticals, such as phytosterols and tocopherols, canolol and phenolic compounds in the extracted oil such as rapeseed oil. This can be a new step to produce nutritional vegetable oils with improved shelf life because of high antioxidant content.
Abstract: This paper investigates the effectiveness of the use of
seismic isolation devices on the overall 3D seismic response of
curved highway viaducts with an emphasis on expansion joints.
Furthermore, an evaluation of the effectiveness of the use of cable
restrainers is presented. For this purpose, the bridge seismic
performance has been evaluated on four different radii of curvature,
considering two cases: restrained and unrestrained curved viaducts.
Depending on the radius of curvature, three-dimensional non-linear
dynamic analysis shows the vulnerability of curved viaducts to
pounding and deck unseating damage. In this study, the efficiency of
using LRB supports combined with cable restrainers on curved
viaducts is demonstrated, not only by reducing in all cases the
possible damage, but also by providing a similar behavior in the
viaducts despite of curvature radius.
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: Team distillation assisted by microwave extraction
(SDAM) considered as accelerated technique extraction is a
combination of microwave heating and steam distillation, performed
at atmospheric pressure. SDAM has been compared with the same
technique coupled with the cryogrinding of seeds (SDAM -CG).
Isolation and concentration of volatile compounds are performed by a
single stage for the extraction of essential oil from Cuminum
cyminum seeds. The essential oils extracted by these two methods for
5 min were quantitatively (yield) and qualitatively (aromatic profile)
no similar. These methods yield an essential oil with higher amounts
of more valuable oxygenated compounds, and allow substantial
savings of costs, in terms of time, energy and plant material. SDAM
and SDAM-CG is a green technology and appears as a good
alternative for the extraction of essential oils from aromatic plants.
Abstract: In order to improve the effect of isolation structure, the
principles and behaviours of the base-isolation system are studied, and
the types and characteristics of the base-isolation are also discussed.
Compared to the traditional aseismatic structures, the base isolation
structures decrease the seismic response obviously: the total structural
aseismatic value decreases to 1/4-1/32 and the seismic shear stress in
the upper structure decreases to 1/14-1/23. In the huge seism, the
structure can have an obvious aseismatic effect.
Abstract: According to FDA (Food and Drug Administration of the United States), vinegar is definedas a sour liquid containing at least 4 grams acetic acid in 100 cubic centimeter (4% solution of acetic acid) of solution that is produced from sugary materials by alcoholic fermentation. In the base of microbial starters, vinegars could be contained of more than 50 types of volatile and aromatic substances that responsible for their sweet taste and smelling. Recently the vinegar industry has a great proportion in agriculture, food and microbial biotechnology. The acetic acid bacteria are from the family Acetobacteraceae. Regarding to the latest version of Bergy-s Mannual of Systematic Bacteriology that has categorized bacteria in the base of their 16s RNA differences, the most important acetic acid genera are included Acetobacter (genus I), Gluconacetobacter (genus VIII) and Gluconobacter (genus IX). The genus Acetobacter that is primarily used in vinegar manufacturing plants is a gram negative, obligate aerobe coccus or rod shaped bacterium with the size 0.6 - 0.8 X 1.0 - 4.0 μm, nonmotile or motile with peritrichous flagella and catalase positive – oxidase negative biochemically. Some strains are overoxidizer that could convert acetic acid to carbon dioxide and water.In this research one Acetobacter native strain with high acetic acid productivity was isolated from Iranian white – red cherry. We used two specific culture media include Carr medium [yeast extract, 3%; ethanol, 2% (v/v); bromocresol green, 0.002%; agar, 2% and distilled water, 1000 ml], Frateur medium [yeast extract, 10 g/l; CaCO3, 20 g/l; ethanol, 20 g/l; agar, 20 g/l and distilled water, 1000 ml] and an industrial culture medium. In addition to high acetic acid production and high growth rate, this strain had a good tolerance against ethanol concentration that was examined using modified Carr media with 5%, 7% and 9% ethanol concentrations. While the industrial strains of acetic acid bacteria grow in the thermal range of 28 – 30 °C, this strain was adapted for growth in 34 – 36 °C after 96 hours incubation period. These dramatic characteristics suggest a potential biotechnological strain in production of cherry vinegar with a sweet smell and different nutritional properties in comparison to recent vinegar types. The lack of growth after 24, 48 and 72 hours incubation at 34 – 36 °C and the growth after 96 hours indicates a good and fast thermal flexibility of this strain as a significant characteristic of biotechnological and industrial strains.
Abstract: This paper describes a new supervised fusion (hybrid)
electrocardiogram (ECG) classification solution consisting of a new
QRS complex geometrical feature extraction as well as a new version
of the learning vector quantization (LVQ) classification algorithm
aimed for overcoming the stability-plasticity dilemma. Toward this
objective, after detection and delineation of the major events of ECG
signal via an appropriate algorithm, each QRS region and also its
corresponding discrete wavelet transform (DWT) are supposed as
virtual images and each of them is divided into eight polar sectors.
Then, the curve length of each excerpted segment is calculated
and is used as the element of the feature space. To increase the
robustness of the proposed classification algorithm versus noise,
artifacts and arrhythmic outliers, a fusion structure consisting of
five different classifiers namely as Support Vector Machine (SVM),
Modified Learning Vector Quantization (MLVQ) and three Multi
Layer Perceptron-Back Propagation (MLP–BP) neural networks with
different topologies were designed and implemented. The new proposed
algorithm was applied to all 48 MIT–BIH Arrhythmia Database
records (within–record analysis) and the discrimination power of the
classifier in isolation of different beat types of each record was
assessed and as the result, the average accuracy value Acc=98.51%
was obtained. Also, the proposed method was applied to 6 number
of arrhythmias (Normal, LBBB, RBBB, PVC, APB, PB) belonging
to 20 different records of the aforementioned database (between–
record analysis) and the average value of Acc=95.6% was achieved.
To evaluate performance quality of the new proposed hybrid learning
machine, the obtained results were compared with similar peer–
reviewed studies in this area.
Abstract: Emergence of smartphones brings to live the concept
of converged devices with the availability of web amenities. Such
trend also challenges the mobile devices manufactures and service
providers in many aspects, such as security on mobile phones,
complex and long time design flow, as well as higher development
cost. Among these aspects, security on mobile phones is getting more
and more attention. Microkernel based virtualization technology will
play a critical role in addressing these challenges and meeting mobile
market needs and preferences, since virtualization provides essential
isolation for security reasons and it allows multiple operating systems
to run on one processor accelerating development and cutting development
cost. However, virtualization benefits do not come for free.
As an additional software layer, it adds some inevitable virtualization
overhead to the system, which may decrease the system performance.
In this paper we evaluate and analyze the virtualization performance
cost of L4 microkernel based virtualization on a competitive mobile
phone by comparing the L4Linux, a para-virtualized Linux on top of
L4 microkernel, with the native Linux performance using lmbench
and a set of typical mobile phone applications.
Abstract: Hazardous Material transportation by road is coupled
with inherent risk of accidents causing loss of lives, grievous injuries,
property losses and environmental damages. The most common type
of hazmat road accident happens to be the releases (78%) of
hazardous substances, followed by fires (28%), explosions (14%) and
vapour/ gas clouds (6 %.).
The paper is discussing initially the probable 'Impact Zones'
likely to be caused by one flammable (LPG) and one toxic (ethylene
oxide) chemicals being transported through a sizable segment of a
State Highway connecting three notified Industrial zones in Surat
district in Western India housing 26 MAH industrial units. Three
'hotspots' were identified along the highway segment depending on
the particular chemical traffic and the population distribution within
500 meters on either sides. The thermal radiation and explosion
overpressure have been calculated for LPG / Ethylene Oxide BLEVE
scenarios along with toxic release scenario for ethylene oxide.
Besides, the dispersion calculations for ethylene oxide toxic release
have been made for each 'hotspot' location and the impact zones
have been mapped for the LOC concentrations. Subsequently, the
maximum Initial Isolation and the protective zones were calculated
based on ERPG-3 and ERPG-2 values of ethylene oxide respectively
which are estimated taking the worst case scenario under worst
weather conditions. The data analysis will be helpful to the local
administration in capacity building with respect to rescue /
evacuation and medical preparedness and quantitative inputs to
augment the District Offsite Emergency Plan document.
Abstract: Today, biogenic magnetite nanoparticles among
magnetic nanoparticles have unique attracted attention because of
their magnetic characteristics and potential applications in various
fields such as therapeutic and diagnostic. A well known example of
these biogenic nanoparticles is magnetosomes of magnetotactic
bacteria. In this research, we used two different types of technique for
the isolation and purification of magnetosome nanoparticles from the
isolated magnetotactic bacterial cells, heat-alkaline treatment and
sonication. Also we evaluated pyrogen content and sterility of
synthesized the isolated individual magnetosome by the Limulus
Amoebocyte Lysate test and direct impedimetric method
respectively.