Abstract: The new optimization method for fiber orientation
angle optimization of symmetrical multilayer plates like plywood is
proposed. Optimization method consists of seeking for minimal
compliance by choosing appropriate fiber orientation angle in outer
layers of flexural plate. The discrete values of fiber orientation angles
are used in method. Optimization results of simply supported plate
and multispan plate with uniformly distributed load are provided.
Results show that stiffness could be increased up to 20% by changing
wood fiber orientation angle in one or two outer layers.
Abstract: In the present work we model a Multiquantum Well
structure Separate Absorption and Charge Multiplication Avalanche
Photodiode (MQW-SACM-APD), while the Absorption region
coincide with the MQW. We consider the nonuniformity of electric
field using split-step method in active region. This model is based on
the carrier rate equations in the different regions of the device. Using
the model we obtain the photocurrent, and dark current. As an
example, InGaAs/InP SACM-APD and MQW-SACM-APD are
simulated. There is a good agreement between the simulation and
experimental results.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: Computational fluid dynamics (CFD) simulations
carried out in this paper show that spacer orientation has a major
influence on temperature patterns and on the heat transfer rates. The
local heat flux values significantly vary from high to very low values
at each filament when spacer touches the membrane surface. The
heat flux profile is more uniform when spacer filaments are not in
contact with the membrane thus making this arrangement more
beneficial. The temperature polarization is also found to be less in
this case when compared to the empty channel.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: Typically thermal power plants are located near to
surface coal mines that produce huge amount of fly ash as a waste
byproduct. Disposal of fly ash causes significant economic and
environmental problems. Now-a-days, research is going on for bulk
utilization of fly ash. In order to increase its percentage utilization, an
investigation was carried out to evaluate its potential for haul road
construction. This paper presents the laboratory California bearing
ratio (CBR) tests and evaluates the effect of lime on CBR behavior of
fly ash - mine overburden mixes. Tests were performed with different
percentages of lime (2%, 3%, 6%, and 9%). The results show that the
increase in bearing ratio of fly ash-overburden mixes was achieved
by lime treatment. Scanning electron microscopy (SEM) analyses
were conducted on 28 days cured specimens. The SEM study showed
that the bearing ratio development is related to the microstructural
development.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: We consider different types of aggregation operators
such as the heavy ordered weighted averaging (HOWA) operator and
the fuzzy ordered weighted averaging (FOWA) operator. We
introduce a new extension of the OWA operator called the fuzzy
heavy ordered weighted averaging (FHOWA) operator. The main
characteristic of this aggregation operator is that it deals with
uncertain information represented in the form of fuzzy numbers (FN)
in the HOWA operator. We develop the basic concepts of this
operator and study some of its properties. We also develop a wide
range of families of FHOWA operators such as the fuzzy push up
allocation, the fuzzy push down allocation, the fuzzy median
allocation and the fuzzy uniform allocation.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: An immunomodulator bioproduct is prepared in a
batch bioprocess with a modified bacterium Pseudomonas
aeruginosa. The bioprocess is performed in 100 L Bioengineering
bioreactor with 42 L cultivation medium made of peptone, meat
extract and sodium chloride. The optimal bioprocess parameters were
determined: temperature – 37 0C, agitation speed - 300 rpm, aeration
rate – 40 L/min, pressure – 0.5 bar, Dow Corning Antifoam M-max.
4 % of the medium volume, duration - 6 hours. This kind of
bioprocesses are appreciated as difficult to control because their
dynamic behavior is highly nonlinear and time varying. The aim of
the paper is to present (by comparison) different models based on
experimental data.
The analysis criteria were modeling error and convergence rate.
The estimated values and the modeling analysis were done by using
the Table Curve 2D.
The preliminary conclusions indicate Andrews-s model with a
maximum specific growth rate of the bacterium in the range of
0.8 h-1.
Abstract: This work focuses on analysis of classical heat transfer equation regularized with Maxwell-Cattaneo transfer law. Computer simulations are performed in MATLAB environment. Numerical experiments are first developed on classical Fourier equation, then Maxwell-Cattaneo law is considered. Corresponding equation is regularized with a balancing diffusion term to stabilize discretizing scheme with adjusted time and space numerical steps. Several cases including a convective term in model equations are discussed, and results are given. It is shown that limiting conditions on regularizing parameters have to be satisfied in convective case for Maxwell-Cattaneo regularization to give physically acceptable solutions. In all valid cases, uniform convergence to solution of initial heat equation with Fourier law is observed, even in nonlinear case.
Abstract: Three-dimensional simulation of harmonic up
generation in free electron laser amplifier operating simultaneously
with a cold and relativistic electron beam is presented in steady-state
regime where the slippage of the electromagnetic wave with respect
to the electron beam is ignored. By using slowly varying envelope
approximation and applying the source-dependent expansion to wave
equations, electromagnetic fields are represented in terms of the
Hermit Gaussian modes which are well suited for the planar wiggler
configuration. The electron dynamics is described by the fully threedimensional
Lorentz force equation in presence of the realistic planar
magnetostatic wiggler and electromagnetic fields. A set of coupled
nonlinear first-order differential equations is derived and solved
numerically. The fundamental and third harmonic radiation of the
beam is considered. In addition to uniform beam, prebunched
electron beam has also been studied. For this effect of sinusoidal
distribution of entry times for the electron beam on the evolution of
radiation is compared with uniform distribution. It is shown that
prebunching reduces the saturation length substantially. For
efficiency enhancement the wiggler is set to decrease linearly when
the radiation of the third harmonic saturates. The optimum starting
point of tapering and the slope of radiation in the amplitude of
wiggler are found by successive run of the code.
Abstract: Mathematical models of dynamics employing exterior calculus are mathematical representations of the same unifying principle; namely, the description of a dynamic system with a characteristic differential one-form on an odd-dimensional differentiable manifold leads, by analysis with exterior calculus, to a set of differential equations and a characteristic tangent vector (vortex vector) which define transformations of the system. Using this principle, a mathematical model for economic growth is constructed by proposing a characteristic differential one-form for economic growth dynamics (analogous to the action in Hamiltonian dynamics), then generating a pair of characteristic differential equations and solving these equations for the rate of economic growth as a function of labor and capital. By contracting the characteristic differential one-form with the vortex vector, the Lagrangian for economic growth dynamics is obtained.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: Mel Frequency Cepstral Coefficient (MFCC) features
are widely used as acoustic features for speech recognition as well
as speaker recognition. In MFCC feature representation, the Mel frequency
scale is used to get a high resolution in low frequency region,
and a low resolution in high frequency region. This kind of processing
is good for obtaining stable phonetic information, but not suitable
for speaker features that are located in high frequency regions. The
speaker individual information, which is non-uniformly distributed
in the high frequencies, is equally important for speaker recognition.
Based on this fact we proposed an admissible wavelet packet based
filter structure for speaker identification. Multiresolution capabilities
of wavelet packet transform are used to derive the new features.
The proposed scheme differs from previous wavelet based works,
mainly in designing the filter structure. Unlike others, the proposed
filter structure does not follow Mel scale. The closed-set speaker
identification experiments performed on the TIMIT database shows
improved identification performance compared to other commonly
used Mel scale based filter structures using wavelets.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: The case study was conducted to show the effect of milking method in goat called half day milking on the milk production and the growth of kids. Data were collected by interviewing farmers and investigating goat production in the communal goat housing from June 2008 to May 2009. The interview was conducted to collect data about goat management. The observations were conducted on 10 goats, which were selected based on the uniformity of age, number of kid born/goat and the milking method in practice. The samples were divided into two groups; those were full 3 months nursing and half day milked goats (in this group the kids were separated from goat during the previous night milking and then the kids were allowed to suck the goat during the day). The result showed that the communal goat housing had 138 goats and 25% of the farmers milked the goat. The implementation of half day milking increased the milk production significantly (P
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.