Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: High Pressure Raman scattering measurements of KDP:Mn were performed at room temperatures. The X-ray powder diffraction patterns taken at room temperature by Rietveld refinement showed that doped samples of KDP-Mn have the same tetragonal structure of a pure KDP crystal, but with a contraction of the crystalline cell. The behavior of the Raman spectra, in particular the emergence of a new modes at 330 cm-1, indicates that KDP:Mn undergoes a structural phase transition with onset at around 4 GP. First principle density-functional theory (DFT) calculations indicate that tetrahedral rotation with pressure is predominantly around the c crystalline direction. Theoretical results indicates that pressure induced tetrahedral rotations leads to change tetrahedral neighborhood, activating librations/bending modes observed for high pressure phase of KDP:Mn with stronger Raman activity.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Reservoirs with high pressures and temperatures
(HPHT) that were considered to be atypical in the past are now
frequent targets for exploration. For downhole oilfield drilling tools
and components, the temperature and pressure affect the mechanical
strength. To address this issue, a finite element analysis (FEA) for
206.84 MPa (30 ksi) pressure and 165°C has been performed on the
pressure housing of the measurement-while-drilling/logging-whiledrilling
(MWD/LWD) density tool.
The density tool is a MWD/LWD sensor that measures the density
of the formation. One of the components of the density tool is the
pressure housing that is positioned in the tool. The FEA results are
compared with the experimental test performed on the pressure
housing of the density tool. Past results show a close match between
the numerical results and the experimental test. This FEA model can
be used for extreme HPHT and ultra HPHT analyses, and/or optimal
design changes.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: High pressure adsorption of carbon dioxide on zeolite
13X was investigated in the pressure range (0 to 4) Mpa and
temperatures 298, 308 and 323K. The data fitting is accomplished
with the Toth, UNILAN, Dubinin-Astakhov and virial adsorption
models which are generally used for micro porous adsorbents such as
zeolites. Comparison with experimental data from the literature
indicated that the virial model would best determine results. These
results may be partly attributed to the flexibility of the virial model
which can accommodate as many constants as the data warrants.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: The friction between two metal surfaces results in a
high frequency noise (squealing) which also occurs during the
braking of wagons with rail brakes in the process of shunting at a
marshalling yard with a hump. At that point the noise level may
exceed 130dB, which is extremely unpleasant for workers and
inhabitants. In our research we developed a new composite material
which does not change braking properties, is capable of taking
extremely high pressure loads, reduces noise and is environmentally
friendly. The noise reduction results had been very good and had
shown a decrease of the high frequency noise almost completely (by
99%) at its source. With our technology we had also reduced general
noise by more than 30dBA.
Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: This paper presents preliminary results of a
technology assessment analysis for the use of high pressure treatment
(HPT) on Halloumi cheese. In particular, it presents the importance
of this traditional Cyprus cheese to the island-s economy, explains its
production process, and gives a brief introduction to HPT and its
application on cheese. More importantly, it offers preliminary results
of HPT of Halloumi samples and a preliminary economic feasibility
study on the financial implications of the introduction of such
technology.
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: Hydrodesulfurization (HDS) of dibenzothiophene
(DBT) in a high pressure batch reactor was done at 320 °C on
CoMoS/Al2O3-B2O3 (4, 10, and 16 wt. % of Boria) using nhexadecane
as solvent, dimethyldisulfide (DMDS) in tetradecane as
sulfur agent, and stirring at 1000 rpm. The effects of boria were
investigated by using X-ray diffraction (XRD), Temperature
programmed desorption (TPD) of ammonia, and Brunauer-Emmet-
Teller (BET) experiments. The results showed that the catalyst
prepared with low boria content (4 wt. %) had HDS activity (in
pseudo first order kinetic constant basis) value ~1.45 times higher to
that of CoMoS/Al2O3 catalyst.
Abstract: Brain ArterioVenous Malformation (BAVM) is an abnormal tangle of brain blood vessels where arteries shunt directly into veins with no intervening capillary bed which causes high pressure and hemorrhage risk. The success of treatment by embolization in interventional neuroradiology is highly dependent on the accuracy of the vessels visualization. In this paper the performance of clustering techniques on vessel segmentation from 3- D rotational angiography (3DRA) images is investigated and a new technique of segmentation is proposed. This method consists in: preprocessing step of image enhancement, then K-Means (KM), Fuzzy C-Means (FCM) and Expectation Maximization (EM) clustering are used to separate vessel pixels from background and artery pixels from vein pixels when possible. A post processing step of removing false-alarm components is applied before constructing a three-dimensional volume of the vessels. The proposed method was tested on six datasets along with a medical assessment of an expert. Obtained results showed encouraging segmentations.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: Erroneous computer entry problems [here: 'e'errors] in hospital labs threaten the patients-–health carers- relationship, undermining the health system credibility. Are e-errors random, and do lab professionals make them accidentally, or may they be traced through meaningful determinants? Theories on internal causality of mistakes compel to seek specific causal ascriptions of hospital lab eerrors instead of accepting some inescapability. Undeniably, 'To Err is Human'. But in view of rapid global health organizational changes, e-errors are too expensive to lack in-depth considerations. Yet, that efunction might supposedly be entrenched in the health carers- job description remains under dispute – at least for Hellenic labs, where e-use falls behind generalized(able) appreciation and application. In this study: i) an empirical basis of a truly high annual cost of e-errors at about €498,000.00 per rural Hellenic hospital was established, hence interest in exploring the issue was sufficiently substantiated; ii) a sample of 270 lab-expert nurses, technicians and doctors were assessed on several personality, burnout and e-error measures, and iii) the hypothesis that the Hardiness vs Alienation personality construct disposition explains resistance vs proclivity to e-errors was tested and verified: Hardiness operates as a resilience source in the encounter of high pressures experienced in the hospital lab, whereas its 'opposite', i.e., Alienation, functions as a predictor, not only of making e-errors, but also of leading to burn-out. Implications for apt interventions are discussed.
Abstract: The effects of different parameters on the
hydrodynamics of trickle bed reactors were discussed for Newtonian
and non-Newtonian foaming systems. The varying parameters are
varying liquid velocities, gas flow velocities and surface tension. The
range for gas velocity is particularly large, thanks to the use of dense
gas to simulate very high pressure conditions. This data bank has
been used to compare the prediction accuracy of the different
trendlines and transition points from the literature. More than 240
experimental points for the trickle flow (GCF) and foaming pulsing
flow (PF/FPF) regime were obtained for present study.
Hydrodynamic characteristics involving dynamic liquid saturation
significantly influenced by gas and liquid flow rates. For 15 and 30
ppm air-aqueous surfactant solutions, dynamic liquid saturation
decreases with higher liquid and gas flow rates considerably in high
interaction regime. With decrease in surface tension i.e. for 45 and 60
ppm air-aqueous surfactant systems, effect was more pronounced
with decreases dynamic liquid saturation very sharply during regime
transition significantly at both low liquid and gas flow rates.
Abstract: The hydrodynamic processes in bubbly liquid flowing
in tubes and nozzles are studied theoretically and numerically. The
principal regularities of non-stationary processes of boiling liquid
outflow are established under conditions of experiments when the
depressurization of a tube with high pressure inside occurs. The
steady-state solution of bubbly liquid flow in the nozzle of round
cross section with high pressure and temperature conditions inside
bubbles is studied accounting for phase transition and chemical
reactions.
Abstract: If organizations like Mellat Bank want to identify its
customer market completely to reach its specified goals, it can
segment the market to offer the product package to the right segment.
Our objective is to offer a segmentation model for Iran banking
market in Mellat bank view. The methodology of this project is
combined by “segmentation on the basis of four part-quality
variables" and “segmentation on the basis of different in means".
Required data are gathered from E-Systems and researcher personal
observation. Finally, the research offers the organization that at first
step form a four dimensional matrix with 756 segments using four
variables named value-based, behavioral, activity style, and activity
level, and at the second step calculate the means of profit for every
cell of matrix in two distinguished work level (levels α1:normal
condition and α2: high pressure condition) and compare the segments
by checking two conditions that are 1- homogeneity every segment
with its sub segment and 2- heterogeneity with other segments, and
so it can do the necessary segmentation process. After all, the last
offer (more explained by an operational example and feedback
algorithm) is to test and update the model because of dynamic
environment, technology, and banking system.