Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: Finite element method was applied to model damage
development in the femoral neck during a sideways fall. The femoral
failure was simulated using the maximum principal strain criterion.
The evolution of damage was consistent with previous studies. It was
initiated by compressive failure at the junction of the superior aspect
of the femoral neck and the greater trochanter. It was followed by
tensile failure that occurred at the inferior aspect of the femoral neck
before a complete transcervical fracture was observed. The estimated
failure line was less than 50° from the horizontal plane (Pauwels type
II).
Abstract: The exploration of this paper will focus on the Cshaped
transition curve. This curve is designed by using the concept
of circle to circle where one circle lies inside other. The degree of
smoothness employed is curvature continuity. The function used in
designing the C-curve is Bézier-like cubic function. This function has
a low degree, flexible for the interactive design of curves and
surfaces and has a shape parameter. The shape parameter is used to
control the C-shape curve. Once the C-shaped curve design is
completed, this curve will be applied to design spur gear tooth. After
the tooth design procedure is finished, the design will be analyzed by
using Finite Element Analysis (FEA). This analysis is used to find
out the applicability of the tooth design and the gear material that
chosen. In this research, Cast Iron 4.5 % Carbon, ASTM A-48 is
selected as a gear material.
Abstract: In this paper, a new formulation for acoustics coupled with linear elasticity is presented. The primary objective of the work is to develop a three dimensional hp adaptive finite element method code destinated for modeling of acoustics of human head. The code will have numerous applications e.g. in designing hearing protection devices for individuals working in high noise environments. The presented work is in the preliminary stage. The variational formulation has been implemented and tested on a sequence of meshes with concentric multi-layer spheres, with material data representing the tissue (the brain), skull and the air. Thus, an efficient solver for coupled elasticity/acoustics problems has been developed, and tested on high contrast material data representing the human head.
Abstract: In this paper a three dimensional thermal model of
high breaking capacity fuse with unequal fuse links is proposed for
both steady-state or transient conditions. The influence of ambient
temperature and electric current on the temperature distribution
inside the fuse, has been investigated. A thermal analysis of the
unbalanced distribution of the electric current through the fuse
elements and their influence on fuse link temperature rise, has been
performed. To validate the three dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: Steel made pipelines with different diameters are used
for transmitting oil and gas which in many cases are buried in soil
under the sea bed or immersed in sea water. External corrosion of
pipes is an important form of deterioration due to the aggressive
environment of sea water. Corrosion normally results in pits. Hence,
using the finite element method, namely ABAQUS software, this
paper estimates the amount of pressure capacity reduction of a pipecontaining
a semi-elliptical pitting corrosion and the rate of corrosion
during the pipeline life of 25 years.
Abstract: In the territories where high-intensity
earthquakes are frequent is paid attention to the solving of the
seismic problems. In the paper are described two
computational model variants based on finite element method
of the construction with different subsoil simulation (rigid or
elastic subsoil) is used. For simulation and calculations
program system based on method final elements ANSYS was
used. Seismic responses calculations of residential building
structure were effected on loading characterized by
accelerogram for comparing with the responses spectra
method.
Abstract: Chatter vibration has been a troublesome problem for a
machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process. Therefore the dynamic vibration behavior of spindle tool
system greatly determines the performance of machine tool. The
purpose of this study is to investigate the influences of the machine
frame structure on the dynamic frequency of spindle tool unit through
finite element modeling approach. To this end, a realistic finite
element model of the vertical milling system was created by
incorporated the spindle-bearing model into the spindle head stock of
the machine frame. Using this model, the dynamic characteristics of
the milling machines with different structural designs of spindle head
stock and identical spindle tool unit were demonstrated. The results of
the finite element modeling reveal that the spindle tool unit behaves
more compliant when the excited frequency approaches the natural
mode of the spindle tool; while the spindle tool show a higher dynamic
stiffness at lower frequency that may be initiated by the structural
mode of milling head. Under this condition, it is concluded that the
structural configuration of spindle head stock associated with the
vertical column of milling machine plays an important role in
determining the machining dynamics of the spindle unit.
Abstract: Air bending is one of the important metal forming
processes, because of its simplicity and large field application.
Accuracy of analytical and empirical models reported for the analysis
of bending processes is governed by simplifying assumption and do
not consider the effect of dynamic parameters. Number of researches
is reported on the finite element analysis (FEA) of V-bending, Ubending,
and air V-bending processes. FEA of bending is found to be
very sensitive to many physical and numerical parameters. FE
models must be computationally efficient for practical use. Reported
work shows the 3D FEA of air bending process using Hyperform LSDYNA
and its comparison with, published 3D FEA results of air
bending in Ansys LS-DYNA and experimental results. Observing the
planer symmetry and based on the assumption of plane strain
condition, air bending problem was modeled in 2D with symmetric
boundary condition in width. Stress-strain results of 2D FEA were
compared with 3D FEA results and experiments. Simplification of
air bending problem from 3D to 2D resulted into tremendous
reduction in the solution time with only marginal effect on stressstrain
results. FE model simplification by studying the problem
symmetry is more efficient and practical approach for solution of
more complex large dimensions slow forming processes.
Abstract: In this paper, an H1-Galerkin mixed finite element method is discussed for the coupled Burgers equations. The optimal error estimates of the semi-discrete and fully discrete schemes of the coupled Burgers equation are derived.
Abstract: Sensory nerves in the foot play an important part in the diagnosis of various neuropathydisorders, especially in diabetes mellitus.However, a detailed description of the anatomical distribution of the nerves is currently lacking. A computationalmodel of the afferent nerves inthe foot may bea useful tool for the study of diabetic neuropathy. In this study, we present the development of an anatomically-based model of various major sensory nerves of the sole and dorsal sidesof the foot. In addition, we presentan algorithm for generating synthetic somatosensory nerve networks in the big-toe region of a right foot model. The algorithm was based on a modified version of the Monte Carlo algorithm, with the capability of being able to vary the intra-epidermal nerve fiber density in differentregionsof the foot model. Preliminary results from the combinedmodel show the realistic anatomical structure of the major nerves as well as the smaller somatosensory nerves of the foot. The model may now be developed to investigate the functional outcomes of structural neuropathyindiabetic patients.
Abstract: This study is to investigate the electroencephalogram (EEG) differences generated from a normal and Alzheimer-s disease (AD) sources. We also investigate the effects of brain tissue distortions due to AD on EEG. We develop a realistic head model from T1 weighted magnetic resonance imaging (MRI) using finite element method (FEM) for normal source (somatosensory cortex (SC) in parietal lobe) and AD sources (right amygdala (RA) and left amygdala (LA) in medial temporal lobe). Then, we compare the AD sourced EEGs to the SC sourced EEG for studying the nature of potential changes due to sources and 5% to 20% brain tissue distortions. We find an average of 0.15 magnification errors produced by AD sourced EEGs. Different brain tissue distortion models also generate the maximum 0.07 magnification. EEGs obtained from AD sources and different brain tissue distortion levels vary scalp potentials from normal source, and the electrodes residing in parietal and temporal lobes are more sensitive than other electrodes for AD sourced EEG.
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: A subsea hydrocarbon production system can undergo planned and unplanned shutdowns during the life of the field. The thermal FEA is used to simulate the cool down to verify the insulation design of the subsea equipment, but it is also used to derive an acceptable insulation design for the cold spots. The driving factors of subsea analyses require fast responding and accurate models of the equipment cool down. This paper presents cool down analysis carried out by a Krylov subspace reduction method, and compares this approach to the commonly used FEA solvers. The model considered represents a typical component of a subsea production system, a closed valve on a dead leg. The results from the Krylov reduction method exhibits the least error and requires the shortest computational time to reach the solution. These findings make the Krylov model order reduction method very suitable for the above mentioned subsea applications.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: This work deals with modeling and simulation of SO2 removal in a ceramic membrane by means of FEM. A mass transfer model was developed to predict the performance of SO2 absorption in a chemical solvent. The model was based on solving conservation equations for gas component in the membrane. Computational fluid dynamics (CFD) of mass and momentum were used to solve the model equations. The simulations aimed to obtain the distribution of gas concentration in the absorption process. The effect of the operating parameters on the efficiency of the ceramic membrane was evaluated. The modeling findings showed that the gas phase velocity has significant effect on the removal of gas whereas the liquid phase does not affect the SO2 removal significantly. It is also indicated that the main mass transfer resistance is placed in the membrane and gas phase because of high tortuosity of the ceramic membrane.
Abstract: The development of shape and size of a crack in a
pressure vessel under uniaxial and biaxial loadings is important in
fitness-for-service evaluations such as leak-before-break. In this
work finite element modelling was used to evaluate the mean stress
and the J-integral around a front of a surface-breaking crack. A
procedure on the basis of ductile tearing resistance curves of high and
low constrained fracture mechanics geometries was developed to
estimate the amount of ductile crack extension for surface-breaking
cracks and to show the evolution of the initial crack shape. The
results showed non-uniform constraint levels and crack driving forces
around the crack front at large deformation levels. It was also shown
that initially semi-elliptical surface cracks under biaxial load
developed higher constraint levels around the crack front than in
uniaxial tension. However similar crack shapes were observed with
more extensions associated with cracks under biaxial loading.
Abstract: In this paper presented initial design of Low Speed
Axial Flux Permanent Magnet (AFPM) Machine with Non-Slotted
TORUS topology type by use of certain algorithm (Appendix).
Validation of design algorithm studied by means of selected data of
an initial prototype machine. Analytically design calculation carried
out by means of design algorithm and obtained results compared with
results of Finite Element Method (FEM).
Abstract: Multilobe bearings are found to be more stable than circular bearings. A three lobe bearing also possesses good stability characteristics. Sometimes the line of action of the load does not pass through the axis of a bearing and is shifted on either side by a few degrees. Load orientation is one of the factors that affect the stability of a three lobe bearing. The effect of load orientation on the stability of a three-lobe has been discussed in this paper. The results show that stability of a three-lobe bearing supporting either rigid or flexible rotor is increased for the positive values of load orientation i.e. when the load line is shifted in the opposite direction of rotation.