Abstract: Technological and sociological developments in the automotive sector are shifting the focus of design towards developing a better understanding of driver needs, desires and emotions. Human centred design methods are being more frequently applied to automotive research, including the use of systems to detect human emotions in real-time. One method for a non-contact measurement of emotion with low intrusiveness is Facial-Expression Analysis (FEA). This paper describes a research study investigating emotional responses of 22 participants in a naturalistic driving environment by applying a multi-method approach. The research explored the possibility to investigate emotional responses and their frequencies during naturalistic driving through real-time FEA. Observational analysis was conducted to assign causes to the collected emotional responses. In total, 730 emotional responses were measured in the collective study time of 440 minutes. Causes were assigned to 92% of the measured emotional responses. This research establishes and validates a methodology for the study of emotions and their causes in the driving environment through which systems and factors causing positive and negative emotional effects can be identified.
Abstract: The dynamic performance of a 4-way solenoid operated hydraulic spool valve has been analyzed by means of a one-dimensional modeling approach capturing flow, magnetic and fluid forces, valve inertia forces, fluid compressibility, and damping. Increased model accuracy was achieved by analyzing the detailed three-dimensional electromagnetic behavior of the solenoids and flow behavior through the spool valve body for a set of relevant operating conditions, thereby allowing the accurate mapping of flow and magnetic forces on the moving valve body, in lieu of representing the respective forces by lower-order models or by means of simplistic textbook correlations. The resulting high-fidelity one-dimensional model provided the basis for specific and timely design modification eliminating experimentally observed valve oscillations.
Abstract: Ball joints support and guide certain automotive parts that move relative to the frame of the vehicle. Such ball joints are covered and protected from dust, mud, and other interfering materials by ball-joint boots made of rubber—a flexible and near-incompressible material. The boots may experience twisting and bending deformations because of the motion of the joint arm. Thus, environmental and endurance tests of ball-joint boots apply both bending and twisting deformations. In this study, environmental and endurance testing was simulated via the finite element method performed by using a commercial software package. The ranges of principal stress and principal strain values that are known to directly affect the fatigue lives of the parts were sought. By defining these ranges, the number of iterative tests and modifications of the materials and dimensions of the boot can be decreased. Therefore, instead of performing actual part tests, manufacturers can perform standard fatigue tests in trials of different materials by applying only the defined range of stress or strain values.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: Low volume roads are widely used all over the world. To improve their quality the computer simulation of their behavior is proposed. The FEM model enables to determine stress and displacement conditions in the pavement and/or also in the particular material layers. Different variants of pavement layers, material used, humidity as well as loading conditions can be studied. Among others, the input information about material properties of individual layers made from recycled materials is crucial for obtaining results as exact as possible. For this purpose the cyclic-load triaxial test machine testing of cyclic-load performance of materials is a promising test method. The test is able to simulate the real traffic loading on particular materials taking into account the changes in the horizontal stress conditions produced in particular layers by crossings of vehicles. Also the test specimen can be prepared with different amount of water. Thus modulus of elasticity (Young modulus) of different materials including recycled ones can be measured under the different conditions of horizontal and vertical stresses as well as under the different humidity conditions. Using the proposed testing procedure the modulus of elasticity of recycled materials used in the newly built low volume road is obtained under different stress and humidity conditions set to standard, dry and fully saturated level. Obtained values of modulus of elasticity are used in FEA.
Abstract: A dead leg is a typical subsea production system
component. CFD is required to model heat transfer within the dead
leg. Unfortunately its solution is time demanding and thus not
suitable for fast prediction or repeated simulations. Therefore there is
a need to create a thermal FEA model, mimicking the heat flows and
temperatures seen in CFD cool down simulations.
This paper describes the conventional way of tuning and a new
automated way using parametric model order reduction (PMOR)
together with an optimization algorithm. The tuned FE analyses
replicate the steady state CFD parameters within a maximum error in
heat flow of 6 % and 3 % using manual and PMOR method
respectively. During cool down, the relative error of the tuned FEA
models with respect to temperature is below 5% comparing to the
CFD. In addition, the PMOR method obtained the correct FEA setup
five times faster than the manually tuned FEA.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: In this paper, the strength of a stabilizer is determined when the static and fatigue multiaxial loading are applied. Stabilizer is a part of suspension system in the heavy truck for stabilizing the cabin against the vibration of the road which composes of a thin-walled tube joined to a forge component by fillet weld. The component is loaded by non proportional random sequence of torsion and bending. Residual stress of welding process is considered here for static loading. This static loading with road irregularities are applied in this study as fatigue case that can affected in the fillet welded area of this part. The stresses in the welded structure are calculated using FEA. In addition, the fatigue with multi axial loading in the fillet weld is also investigated and the critical zone of the stabilizer is specified and presented by graphs. Residual stresses that have been resulted by the thermal forces are considered in FEA. Force increasing is the element of finding the critical point of the component.
Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.