Abstract: The use of machine vision to inspect the outcome of
surgical tasks is investigated, with the aim of incorporating this
approach in robotic surgery systems. Machine vision is a non-contact
form of inspection i.e. no part of the vision system is in direct contact
with the patient, and is therefore well suited for surgery where
sterility is an important consideration,. As a proof-of-concept, three
primary surgical tasks for a common neurosurgical procedure were
inspected using machine vision. Experiments were performed on
cadaveric pig heads to simulate the two possible outcomes i.e.
satisfactory or unsatisfactory, for tasks involved in making a burr
hole, namely incision, retraction, and drilling. We identify low level
image features to distinguish the two outcomes, as well as report on
results that validate our proposed approach. The potential of using
machine vision in a surgical environment, and the challenges that
must be addressed, are identified and discussed.
Abstract: One major source of performance decline in speaker
recognition system is channel mismatch between training and testing.
This paper focuses on improving channel robustness of speaker
recognition system in two aspects of channel compensation technique
and channel robust features. The system is text-independent speaker
identification system based on two-stage recognition. In the aspect of
channel compensation technique, this paper applies MAP (Maximum
A Posterior Probability) channel compensation technique, which was
used in speech recognition, to speaker recognition system. In the
aspect of channel robust features, this paper introduces
pitch-dependent features and pitch-dependent speaker model for the
second stage recognition. Based on the first stage recognition to
testing speech using GMM (Gaussian Mixture Model), the system
uses GMM scores to decide if it needs to be recognized again. If it
needs to, the system selects a few speakers from all of the speakers
who participate in the first stage recognition for the second stage
recognition. For each selected speaker, the system obtains 3
pitch-dependent results from his pitch-dependent speaker model, and
then uses ANN (Artificial Neural Network) to unite the 3
pitch-dependent results and 1 GMM score for getting a fused result.
The system makes the second stage recognition based on these fused
results. The experiments show that the correct rate of two-stage
recognition system based on MAP channel compensation technique
and pitch-dependent features is 41.7% better than the baseline system
for closed-set test.
Abstract: This paper examines the implementation of RC5 block cipher for digital images along with its detailed security analysis. A complete specification for the method of application of the RC5 block cipher to digital images is given. The security analysis of RC5 block cipher for digital images against entropy attack, bruteforce, statistical, and differential attacks is explored from strict cryptographic viewpoint. Experiments and results verify and prove that RC5 block cipher is highly secure for real-time image encryption from cryptographic viewpoint. Thorough experimental tests are carried out with detailed analysis, demonstrating the high security of RC5 block cipher algorithm.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: The proper assessment of interaxial distance and
convergence control are important factors in stereoscopic imaging
technology to make an efficient 3D image. To control interaxial
distance and convergence for efficient 3D shooting, horizontal 3D
camera rig is designed using some hardware components like 'LM
Guide', 'Goniometer' and 'Rotation Stage'. The horizontal 3D camera
rig system can be properly aligned by moving the two cameras
horizontally in same or opposite directions, by adjusting the camera
angle and finally considering horizontal swing as well as vertical
swing. In this paper, the relationship between interaxial distance and
convergence angle control are discussed and intensive experiments are
performed in order to demonstrate an easy and effective 3D shooting.
Abstract: In this study an extensive experimental research is
carried out to develop a better understanding of the effects of Piano Key (PK) weir geometry on weir flow threshold submergence.
Experiments were conducted in a 12 m long, 0.4 m wide and 0.7 m deep rectangular glass wall flume. The main objectives were to
investigate the effect of the PK weir geometries including the weir
length, weir height, inlet-outlet key widths, upstream and
downstream apex overhangs, and slopped floors on threshold submergence and study the hydraulic flow characteristics. From the
experimental results, a practical formula is proposed to evaluate the flow threshold submergence over PK weirs.
Abstract: Using plug flow model in conjunction with
experimental solute concentration profiles, overall volumetric mass
transfer coefficient based on continuous phase (Koca), in a packed
liquid-liquid extraction column has been optimized. Number of 12
experiments has been done using standard system of water/acid
acetic/toluene in a 6 cm diameter, 120 cm height column. Thorough
consideration of influencing parameters we intended to correlate
dimensionless parameters in term of overall Sherwood number which
has an acceptable average error of about 15.8%.
Abstract: Hydrogen is regarded to play an important role in
future energy systems because it can be produced from abundant
resources and its combustion only generates water. The disposal of
waste tyres is a major problem in environmental management
throughout the world. The use of waste materials as a source of
hydrogen is particularly of interest in that it would also solve a waste
treatment problem. There is much interest in the use of alternative
feedstocks for the production of hydrogen since more than 95% of
current production is from fossil fuels. The pyrolysis of waste tyres
for the production of liquid fuels, activated carbons and gases has
been extensively researched. However, combining pyrolysis with
gasification is a novel process that can gasify the gaseous products
from pyrolysis. In this paper, an experimental investigation into the
production of hydrogen and other gases from the bench scale
pyrolysis-gasification of tyres has been investigated. Experiments
were carried using a two stage system consisting of pyrolysis of the
waste tyres followed by catalytic steam gasification of the evolved
gases and vapours in a second reactor. Experiments were conducted
at a pyrolysis temperature of 500 °C using Ni/Al2O3 as a catalyst. The
results showed that there was a dramatic increase in gas yield and the
potential H2 production when the gasification temperature was
increased from 600 to 900 oC. Overall, the process showed that high
yields of hydrogen can be produced from waste tyres.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: The study concerns an experimental investigation in
the laboratory of the water erosion using a rainfall simulator. We
have focused our attention on the influence of rainfall intensity on
some hydraulic characteristics. The results obtained allow us to
conclude that there is a significant correlation between rainfall
intensity and hydraulic characteristics of runoff (Reynolds number,
Froude number) and sediment concentration.
Abstract: Numerous divergence measures (spectral distance, cepstral
distance, difference of the cepstral coefficients, Kullback-Leibler
divergence, distance given by the General Likelihood Ratio, distance
defined by the Recursive Bayesian Changepoint Detector and the
Mahalanobis measure) are compared in this study. The measures are
used for detection of abrupt spectral changes in synthetic AR signals
via the sliding window algorithm. Two experiments are performed;
the first is focused on detection of single boundary while the second
concentrates on detection of a couple of boundaries. Accuracy of
detection is judged for each method; the measures are compared
according to results of both experiments.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: In this study, in order to clarify wind-induced
phenomena, especially vertical mixing of density stratification in a
closed water area with floating-leaved plants, we conducted hydraulic
experiments on wind flow characteristics, wind wave characteristics,
entrainment phenomena and turbulent structure by using a wind tunnel
test tank and simulated floating-leaved plants. From the experimental
results of wind flow and wind wave characteristics, we quantified the
impact of the occupancy rate of the plants on their resistance
characteristics. From the experimental results of entrainment
phenomena, we defined the parameter that could explain the
magnitude of mixing between the density stratifications, and
quantified the impact of the occupancy rate on vertical mixing
between stratifications. From the experimental results of the turbulent
structure of the upper layer, we clarified the differences in small-scale
turbulence components at each occupancy rate and quantified the
impact of the occupancy rate on the turbulence characteristics. For a
summary of this study, we theoretically quantified wind-induced
entrainment phenomena in a closed water area with luxuriant growth
of floating-leaved plants. The results indicated that the impact of
luxuriant growth of floating-leaved plants in a closed water body
could be seen in the difference in small-scale fluid characteristics, and
these characteristics could be expressed using the small-scale
turbulent components.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: Support vector machines (SVMs) have shown
superior performance compared to other machine learning techniques,
especially in classification problems. Yet one limitation of SVMs is
the lack of an explanation capability which is crucial in some
applications, e.g. in the medical and security domains. In this paper, a
novel approach for eclectic rule-extraction from support vector
machines is presented. This approach utilizes the knowledge acquired
by the SVM and represented in its support vectors as well as the
parameters associated with them. The approach includes three stages;
training, propositional rule-extraction and rule quality evaluation.
Results from four different experiments have demonstrated the value
of the approach for extracting comprehensible rules of high accuracy
and fidelity.
Abstract: In this paper we illuminate a frequency domain based
classification method for video scenes. Videos from certain topical
areas often contain activities with repeating movements. Sports
videos, home improvement videos, or videos showing mechanical
motion are some example areas. Assessing main and side frequencies
of each repeating movement gives rise to the motion type. We
obtain the frequency domain by transforming spatio-temporal motion
trajectories. Further on we explain how to compute frequency features
for video clips and how to use them for classifying. The focus of
the experimental phase is on transforms utilized for our system.
By comparing various transforms, experiments show the optimal
transform for a motion frequency based approach.
Abstract: In this paper we examine the use of global texture analysis based approaches for the purpose of Persian font recognition in machine-printed document images. Most existing methods for font recognition make use of local typographical features and connected component analysis. However derivation of such features is not an easy task. Gabor filters are appropriate tools for texture analysis and are motivated by human visual system. Here we consider document images as textures and use Gabor filter responses for identifying the fonts. The method is content independent and involves no local feature analysis. Two different classifiers Weighted Euclidean Distance and SVM are used for the purpose of classification. Experiments on seven different type faces and four font styles show average accuracy of 85% with WED and 82% with SVM classifier over typefaces
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: Text categorization techniques are widely used to many Information Retrieval (IR) applications. In this paper, we proposed a simple but efficient method that can automatically find the relationship between any pair of terms and documents, also an indexing matrix is established for text categorization. We call this method Indexing Matrix Categorization Machine (IMCM). Several experiments are conducted to show the efficiency and robust of our algorithm.