Abstract: Software Architecture is the basic structure of
software that states the development and advancement of a software
system. Software architecture is also considered as a significant tool
for the construction of high quality software systems. A clean design
leads to the control, value and beauty of software resulting in its
longer life while a bad design is the cause of architectural erosion
where a software evolution completely fails. This paper discusses the
occurrence of software architecture erosion and presents a set of
methods for the detection, declaration and prevention of architecture
erosion. The causes and symptoms of architecture erosion are
observed with the examples of prescriptive and descriptive
architectures and the practices used to stop this erosion are also
discussed by considering different types of software erosion and their
affects. Consequently finding and devising the most suitable
approach for fighting software architecture erosion and in some way
reducing its affect is evaluated and tested on different scenarios.
Abstract: Soil erosion is a very complex phenomenon, resulting
from detachment and transport of soil particles by erosion agents.
The kinetic energy of raindrop is the energy available for detachment
and transport by splashing rain. The soil erodibility is defined as the
ability of soil to resist to erosion. For this purpose, an experimental
study was conducted in the laboratory using rainfall simulator to
study the effect of the kinetic energy of rain (Ec) on the soil
erodibility (K). The soil used was a sandy agricultural soil of 62.08%
coarse sand, 19.14% fine sand, 6.39% fine silt, 5.18% coarse silt and
7.21% clay. The obtained results show that the kinetic energy of
raindrops evolves as a power law with soil erodibility.
Abstract: In order to investigate the effect of Plant Growth
Promoting Rhizobacteria (PGPR) and rhizobium bacteria on grain
yield and some agronomic traits of mungbean (Vigna radiate L.), an
experiment was carried out based on randomized complete block
design with three replications in Malekshahi, Ilam province, Iran
during 2012-2013 cropping season. Experimental treatments
consisted of control treatment, inoculation with rhizobium bacteria,
rhizobium bacteria and Azotobacter, rhizobium bacteria and
Azospirillum, rhizobium bacteria and Pseudomonas, rhizobium
bacteria, Azotobacter and Azospirillum, rhizobium bacteria,
Azotobacter and Pseudomonas, rhizobium bacteria, Azospirillum and
Pseudomonas and rhizobium bacteria, Azotobacter, Azospirillum and
Pseudomonas. The results showed that the effect of PGPR and
rhizobium bacteria were significant affect on grain and its
components in mungbean plant. Grain yield significantly increased
by PGPR and rhizobium bacteria, so that the maximum grain yield
was obtained from rhizobium bacteria + Azospirillum +
Pseudomonas with the amount of 2287 kg.ha-1 as compared to
control treatment. Excessive application of chemical fertilizers causes
environmental and economic problems. That is, the overfertilization
of P and N leads to pollution due to soil erosion and runoff water, so
the use of PGPR and rhizobium bacteria can be justified due to
reduce input costs, increase in grain yield and environmental friendly.
Abstract: Soil confinement systems serve as effective solutions to any erosion control project. Various confinements systems, namely triangular, circular and rectangular with the size of 50, 100, and 150 mm, and with a depth of 10 mm, were embedded in soil samples at slope angle of 60°. The observed soil mass losses for the confined soil systems were much smaller than those from unconfined system. As a result, the size of confinement and rainfall intensity have a direct effect on the soil mass loss. The triangular and rectangular confinement systems showed the lowest and highest soil loss masses, respectively. The slopes also failed much faster in the unconfined system than in the confined slope.
Abstract: This paper presents the experimental results of high-density polyethylene cable spacers for 22 kV distribution systems under salt water dip wheel test based on IEC 62217. The strength of anti-tracking and anti-erosion of cable spacer surface was studied in this study. During the test, dry band arc and corona discharge were observed on cable spacer surface. After 30,000 cycles of salt water dip wheel test, obviously surface erosion and tracking were observed especially on the ground end. Chemical analysis results by fourier transforms infrared spectroscopy showed chemical changed from oxidation and carbonization reaction on tested cable spacer. Increasing of C=O and C=C bonds confirmed occurrence of these reactions.
Abstract: Shoreline erosion problems caused by global warming and sea level rising may result in losing of land areas, so it should be examined regularly to reduce possible negative impacts. Initially in this study, three sets of survey images obtained from the years of 1990, 2001, and 2010, respectively, are digitalized by using graphical software to establish the spatial coordinates of six major beaches around the island of Taiwan. Then, by overlaying the known multi-period images, the change of shoreline can be observed from their distribution of coordinates. In addition, the neural network approximation is used to develop a model for predicting shoreline variation in the years of 2015 and 2020. The comparison results show that there is no significant change of total sandy area for all beaches in the three different periods. However, the prediction results show that two beaches may exhibit an increasing of total sandy areas under a statistical 95% confidence interval. The proposed method adopted in this study may be applicable to other shorelines of interest around the world.
Abstract: Prognostic studies of the shoreline are of utmost importance for Ponta Negra Beach, located in Natal, Northeastern Brazil, where the infrastructure recently built along the shoreline is severely affected by flooding and erosion. This study compares shoreline predictions using three linear regression methods (LMS, LRR and WLR) and tries to discern the best method for different shoreline position scenarios. The methods have shown erosion on the beach in each of the scenarios tested, even in less intense dynamic conditions. The WLA_A with confidence interval of 95% was the well-adjusted model and calculated a retreat of -1.25 m/yr to -2.0 m/yr in hot spot areas. The change of the shoreline on Ponta Negra Beach can be measured as a negative exponential curve. Analysis of these methods has shown a correlation with the morphodynamic stage of the beach.
Abstract: In this study, a physically-based, modeling framework was developed to predict saturated hydraulic conductivity (Ksat) dynamics in the Clear Creek Watershed (CCW), Iowa. The modeling framework integrated selected pedotransfer functions and watershed models with geospatial tools. A number of pedotransfer functions and agricultural watershed models were examined to select the appropriate models that represent the study site conditions. Models selection was based on statistical measures of the models’ errors compared to the Ksat field measurements conducted in the CCW under different soil, climate and land use conditions. The study has shown that the predictions of the combined pedotransfer function of Rosetta and the Water Erosion Prediction Project (WEPP) provided the best agreement to the measured Ksat values in the CCW compared to the other tested models. Therefore, Rosetta and WEPP were integrated with the Geographic Information System (GIS) tools for visualization of the data in forms of geospatial maps and prediction of Ksat variability in CCW due to the seasonal changes in climate and land use activities.
Abstract: The primary objective of this paper is to study the thermal effects of the electric arc on the breaker apparatus contacts for forecasting and improving the contact durability. We will propose a model which takes account of the main influence factors on the erosion contacts. This phenomenon is very complicated because the amount of ejected metal is not necessarily constituted by the whole melted metal bath but this depends on the balance of forces on the contact surface. Consequently, to calculate the metal ejection coefficient, we propose a method which consists in comparing the experimental results with the calculated ones. The proposed model estimates the mass lost by vaporization, by droplets ejection and by the extraction mechanism of liquid or solid metal. In the one-dimensional geometry, to calculate of the contact heating, we used Green’s function which expresses the point source and allows the transition to the surface source. However, for the two- dimensional model we used explicit and implicit numerical methods. The results are similar to those found by Wilson’s experiments.
Abstract: Water erosion is the most important problems of the soil in the Jabel Nefusa area located in northwest of Libya; therefore, erosion station had been established in the Faculty of Veterinary and dryfarming research Station, University of the Al-japel Al-gharbi in Zentan. The length of the station is 72.6 feet, 6 feet width and the percentage of its slope is 3%. The station were established to measure the amount of soil eroded and amount of surface water produced during the seasons 95/96 and 96/97 from each rain storms. The monitoring shows that there was a difference between the two seasons in the number of rainstorms which made differences in the amount of surface runoff water and the amount of soil eroded between the two seasons. Although the slope is low (3%), the soil texture is sandy and the land ploughed twice during each season surface runoff and soil eroded were occurred. The average amount of eroded soil was 3792 grams (gr) per season and the average amount of surface runoff water was 410 liter (L) per season. The amount of surface runoff water would be much greater from Jebel Nefusa upland with steep slopes and collecting of them will save a valuable amount of water which lost as a runoff while this area is in desperate of this water. The regression analysis of variance show strong correlation between rainfall depth and the other two depended variable (the amount of surface runoff water and the amount of eroded soil. It shows also strong correlation between amount of surface runoff water and amount of eroded soil.
Abstract: In order to determine the performance and key design parameters of rocket, the erosion of nozzle throat during solid rocket motor burning have to be calculated. This study aims to predict the nozzle throat erosion in solid rocket motors according to the thrust profile of motor in operating conditions and develop a model for optimum performance of rocket. We investigate the throat radius change in the static test programs. The standard method and thrust coefficient are used for adjusting into the ideal performance for conical nozzles. Pressure and thrust data acquired from the tests are analyzed to determine the instantaneous nozzle throat diameter variation throughout the test duration. The result shows good agreement of calculated correlation comparing with measured erosion rate data showing agreement within 1.6 mm/s. Nozzle thrust coefficient loss is found approximately 24% form nozzle throat erosion during burning.
Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: The morphological short-term evolution of Ponta do Tubarão Island (PTI) was investigated through high accurate surveys based on post-processed kinematic (PPK) relative positioning on Global Navigation Satellite Systems (GNSS). PTI is part of a barrier island system on a high energy northeast Brazilian coastal environment and also an area of high environmental sensitivity. Surveys were carried out quarterly over a two years period from May 2010 to May 2012. This paper assesses statically the performance of digital elevation models (DEM) derived from different interpolation methods to represent morphologic features and to quantify volumetric changes and TIN models shown the best results to that purposes. The MDE allowed quantifying surfaces and volumes in detail as well as identifying the most vulnerable segments of the PTI to erosion and/or accumulation of sediments and relate the alterations to climate conditions. The coastal setting and geometry of PTI protects a significant mangrove ecosystem and some oil and gas facilities installed in the vicinities from damaging effects of strong oceanwaves and currents. Thus, the maintenance of PTI is extremely required but the prediction of its longevity is uncertain because results indicate an irregularity of sedimentary balance and a substantial decline in sediment supply to this coastal area.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: The aim of this research is to develop a fast and
reliable surveillance system based on a personal digital assistant
(PDA) device. This is to extend the capability of the device to detect
moving objects which is already available in personal computers.
Secondly, to compare the performance between Background
subtraction (BS) and Temporal Frame Differencing (TFD) techniques
for PDA platform as to which is more suitable. In order to reduce
noise and to prepare frames for the moving object detection part,
each frame is first converted to a gray-scale representation and then
smoothed using a Gaussian low pass filter. Two moving object
detection schemes i.e., BS and TFD have been analyzed. The
background frame is updated by using Infinite Impulse Response
(IIR) filter so that the background frame is adapted to the varying
illuminate conditions and geometry settings. In order to reduce the
effect of noise pixels resulting from frame differencing
morphological filters erosion and dilation are applied. In this
research, it has been found that TFD technique is more suitable for
motion detection purpose than the BS in term of speed. On average
TFD is approximately 170 ms faster than the BS technique
Abstract: The one of most important objects in implementation
of damage analysis observations is manner of dam break wave
propagation. In this paper velocity and wave height due dam break in
with and without tailwater states for appointment hazardous lands
and flood radius are investigate. In order to modeling above
phenomenon finite volume method of Roe type for solving shallow
water equations is used. Results indicated that in the dry bed state
risk radius due to dam break is too high. While in the wet bed risk
radius has a less wide. Therefore in the first state constructions and
storage facilities are encountered with destruction risk. Further
velocity due to dam break in the second state is more comparing to
the first state. Hence erosion and scour the river bed in the dry bed is
too more compare to the wet bed.
Abstract: Reducing river sediments through path correction and
preservation of river walls leads to considerable reduction of
sedimentation at the pumping stations. Path correction and
preservation of walls is not limited to one particular method but,
depending on various conditions, a combination of several methods
can be employed. In this article, we try to review and evaluate
methods for preservation of river banks in order to reduce sediments.
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.