Abstract: The contamination of 15 ground water resources
of a selected region earmarked for the emergency supply
of population has been monitored. The resources have been selected
on the basis of previous assessment of natural conditions
and the exploitation of territory in their surroundings and infiltration
area. Two resources out of 15 have been excluded from further
exploitation, because they have not met some of the 72 assessed
hygienic indicators of extended analysis. The remaining 13 resources
have been the subject of health risk analysis in relation
to the contamination by arsenic, lead, cadmium, mercury, nickel and
manganese. The risk analysis proved that all 13 resources meet
health standards with regard to the above mentioned purposefully
selected elements and may thus be included into crisis plans. Water
quality of ground resources may be assessed in the same way
with regard to other contaminants.
Abstract: In this paper a three dimensional thermal model of
high breaking capacity fuse with unequal fuse links is proposed for
both steady-state or transient conditions. The influence of ambient
temperature and electric current on the temperature distribution
inside the fuse, has been investigated. A thermal analysis of the
unbalanced distribution of the electric current through the fuse
elements and their influence on fuse link temperature rise, has been
performed. To validate the three dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: In recent years, the use of vector variance as a
measure of multivariate variability has received much attention in
wide range of statistics. This paper deals with a more economic
measure of multivariate variability, defined as vector variance minus
all duplication elements. For high dimensional data, this will increase
the computational efficiency almost 50 % compared to the original
vector variance. Its sampling distribution will be investigated to make
its applications possible.
Abstract: The purpose of this study is mainly to predict collision
frequency on the horizontal tangents combined with vertical curves
using artificial neural network methods. The proposed ANN models
are compared with existing regression models. First, the variables
that affect collision frequency were investigated. It was found that
only the annual average daily traffic, section length, access density,
the rate of vertical curvature, smaller curve radius before and after
the tangent were statistically significant according to related
combinations. Second, three statistical models (negative binomial,
zero inflated Poisson and zero inflated negative binomial) were
developed using the significant variables for three alignment
combinations. Third, ANN models are developed by applying the
same variables for each combination. The results clearly show that
the ANN models have the lowest mean square error value than those
of the statistical models. Similarly, the AIC values of the ANN
models are smaller to those of the regression models for all the
combinations. Consequently, the ANN models have better statistical
performances than statistical models for estimating collision
frequency. The ANN models presented in this paper are
recommended for evaluating the safety impacts 3D alignment
elements on horizontal tangents.
Abstract: In this research work, a novel parallel manipulator
with high positioning and orienting rate is introduced. This
mechanism has two rotational and one translational degree of
freedom. Kinematics and Jacobian analysis are investigated.
Moreover, workspace analysis and optimization has been performed
by using genetic algorithm toolbox in Matlab software. Because of
decreasing moving elements, it is expected much more better
dynamic performance with respect to other counterpart mechanisms
with the same degrees of freedom. In addition, using couple of
cylindrical and revolute joints increased mechanism ability to have
more extended workspace.
Abstract: In the territories where high-intensity
earthquakes are frequent is paid attention to the solving of the
seismic problems. In the paper are described two
computational model variants based on finite element method
of the construction with different subsoil simulation (rigid or
elastic subsoil) is used. For simulation and calculations
program system based on method final elements ANSYS was
used. Seismic responses calculations of residential building
structure were effected on loading characterized by
accelerogram for comparing with the responses spectra
method.
Abstract: Array signal processing involves signal enumeration and source localization. Array signal processing is centered on the ability to fuse temporal and spatial information captured via sampling signals emitted from a number of sources at the sensors of an array in order to carry out a specific estimation task: source characteristics (mainly localization of the sources) and/or array characteristics (mainly array geometry) estimation. Array signal processing is a part of signal processing that uses sensors organized in patterns or arrays, to detect signals and to determine information about them. Beamforming is a general signal processing technique used to control the directionality of the reception or transmission of a signal. Using Beamforming we can direct the majority of signal energy we receive from a group of array. Multiple signal classification (MUSIC) is a highly popular eigenstructure-based estimation method of direction of arrival (DOA) with high resolution. This Paper enumerates the effect of missing sensors in DOA estimation. The accuracy of the MUSIC-based DOA estimation is degraded significantly both by the effects of the missing sensors among the receiving array elements and the unequal channel gain and phase errors of the receiver.
Abstract: One of the main consequences of the ubiquitous usage of Internet as a means to conduct business has been the progressive internationalization of contracts created to support such transactions. As electronic commerce becomes International commerce, the reality is that commercial disputes will occur creating such questions as: "In which country do I bring proceedings?" and "Which law is to be applied to solve disputes?" The decentralized and global structure of the Internet and its decentralized operation have given e-commerce a transnational element that affects two questions essential to any transaction: applicable law and jurisdiction in the event of dispute. The sharing of applicable law and jurisdiction among States in respect of international transactions traditionally has been based on the use of contact factors generally of a territorial nature (the place where real estate is located, customary residence, principal establishment, place of shipping goods). The characteristics of the Internet as a new space sometimes make it difficult to apply these rules, and may make them inoperative or lead to results that are surprising or totally foreign to the contracting parties and other elements and circumstances of the case.
Abstract: One of the main image representations in Mathematical Morphology is the 3D Shape Decomposition Representation, useful for Image Compression and Representation,and Pattern Recognition. The 3D Morphological Shape Decomposition representation can be generalized a number of times,to extend the scope of its algebraic characteristics as much as possible. With these generalizations, the Morphological Shape Decomposition 's role to serve as an efficient image decomposition tool is extended to grayscale images.This work follows the above line, and further develops it. Anew evolutionary branch is added to the 3D Morphological Shape Decomposition's development, by the introduction of a 3D Multi Structuring Element Morphological Shape Decomposition, which permits 3D Morphological Shape Decomposition of 3D binary images (grayscale images) into "multiparameter" families of elements. At the beginning, 3D Morphological Shape Decomposition representations are based only on "1 parameter" families of elements for image decomposition.This paper addresses the gray scale inter frame interpolation by means of mathematical morphology. The new interframe interpolation method is based on generalized morphological 3D Shape Decomposition. This article will present the theoretical background of the morphological interframe interpolation, deduce the new representation and show some application examples.Computer simulations could illustrate results.
Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: This paper presents a real time force sensing instrument that is designed for human gait analysis purposes. This instrument mainly consists of three main elements: the force sensing mat, signal conditioning and switching circuit and data acquisition
device. In order to control and to process the incoming signals from the force sensing mat, Force-Logger and Force-Reloader program are
developed using Labview 8.0. This paper describes the architecture of the force sensing mat, signal conditioning and switching circuit and the real time streaming of the incoming data from the force
sensing mat.
Abstract: In this paper, an analysis is presented, which
demonstrates the effect pre-logic factoring could have on an
automated combinational logic synthesis process succeeding it. The
impact of pre-logic factoring for some arbitrary combinatorial
circuits synthesized within a FPGA based logic design environment
has been analyzed previously. This paper explores a similar effect,
but with the non-regenerative logic synthesized using elements of a
commercial standard cell library. On an overall basis, the results
obtained pertaining to the analysis on a variety of MCNC/IWLS
combinational logic benchmark circuits indicate that pre-logic
factoring has the potential to facilitate simultaneous power, delay and
area optimized synthesis solutions in many cases.
Abstract: Internal controls of accounting are an essential
business function for a growth-oriented organization, and include the
elements of risk assessment, information communications and even
employees' roles and responsibilities. Internal controls of accounting
systems are designed to protect a company from fraud, abuse and
inaccurate data recording and help organizations keep track of
essential financial activities. Internal controls of accounting provide a
streamlined solution for organizing all accounting procedures and
ensuring that the accounting cycle is completed consistently and
successfully. Implementing a formal Accounting Procedures Manual
for the organization allows the financial department to facilitate
several processes and maintain rigorous standards. Internal controls
also allow organizations to keep detailed records, manage and
organize important financial transactions and set a high standard for
the organization's financial management structure and protocols. A
well-implemented system also reduces the risk of accounting errors
and abuse. A well-implemented controls system allows a company's
financial managers to regulate and streamline all functions of the
accounting department. Internal controls of accounting can be set up
for every area to track deposits, monitor check handling, keep track
of creditor accounts, and even assess budgets and financial statements
on an ongoing basis. Setting up an effective accounting system to
monitor accounting reports, analyze records and protect sensitive
financial information also can help a company set clear goals and
make accurate projections. Creating efficient accounting processes
allows an organization to set specific policies and protocols on
accounting procedures, and reach its financial objectives on a regular
basis. Internal accounting controls can help keep track of such areas
as cash-receipt recording, payroll management, appropriate recording
of grants and gifts, cash disbursements by authorized personnel, and
the recording of assets. These systems also can take into account any
government regulations and requirements for financial reporting.
Abstract: Irradiated material is a typical example of a complex
system with nonlinear coupling between its elements. During
irradiation the radiation damage is developed and this development
has bifurcations and qualitatively different kinds of behavior.
The accumulation of primary defects in irradiated crystals is
considered in frame work of nonlinear evolution of complex system.
The thermo-concentration nonlinear feedback is carried out as a
mechanism of self-oscillation development.
It is shown that there are two ways of the defect density evolution
under stationary irradiation. The first is the accumulation of defects;
defect density monotonically grows and tends to its stationary state
for some system parameters. Another way that takes place for
opportune parameters is the development of self-oscillations of the
defect density.
The stationary state, its stability and type are found. The
bifurcation values of parameters (environment temperature, defect
generation rate, etc.) are obtained. The frequency of the selfoscillation
and the conditions of their development is found and
rated. It is shown that defect density, heat fluxes and temperature
during self-oscillations can reach much higher values than the
expected steady-state values. It can lead to a change of typical
operation and an accident, e.g. for nuclear equipment.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: Thermochemcial characteristics of powder fabricated
using oxidation treatment of spent PWR fuel and SIMFUEL were
evaluated for recycling of spent fuel such as DUPIC process.
Especially, the influence of spent fuel burn-ups on the powder
fabrication characteristics was experimentally evaluated, ranging from
27,300 to 65,000 MWd/tU. Densities of powder manufactured from an
oxidation, OREOX and the milling processes at the same process
conditions were compared as a function of the fuel burn-ups
respectively. Also, based on chemical analysis results, homogeneity of
fissile elements in oxidized powder was confirmed.
Abstract: In the context of business incubation (BI) as strategic
enablers, this paper critically reviews the literature relating to the
strategic benefits of BI in the Middle East. The taxonomy of BI
benefits in the strategic elements on 1) type, 2) financial model, 3)
services, 4) objectives, 5) number of clients, 6) number of graduates,
and 7) jobs creation. Understanding the importance of BI benefits can
be significant in the economic development although most incubators
lead to diversify the economy. Thus, taxonomies of the benefits of BI
are produced from both the academic literature and published case
studies. In this way, a classification of strategic benefits elements as
they relate to incubators has been developed to provide a greater
understanding of the benefits needed to obtain a specific element.
The result of this paper is Business incubators is aimed
entrepreneurship, jobs creation, research commercialization and
profitable enterprises in Middle Eastern countries.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: The link between urban planning and design principles and the built environment of an urban renewal area is of interest to the field of urban studies. During the past decade, there has also been increasing interest in urban planning and design; this interest is motivated by the possibility that design policies associated with the built environment can be used to control, manage, and shape individual activity and behavior. However, direct assessments and design techniques of the links between how urban planning design policies influence individuals are still rare in the field. Recent research efforts in urban design have focused on the idea that land use and design policies can be used to increase the quality of design projects for an urban renewal area-s built environment. The development of appropriate design techniques for the built environment is an essential element of this research. Quality function deployment (QFD) is a powerful tool for improving alternative urban design and quality for urban renewal areas, and for procuring a citizen-driven quality system. In this research, we propose an integrated framework based on QFD and an Analytic Network Process (ANP) approach to determine the Alternative Technical Requirements (ATRs) to be considered in designing an urban renewal planning and design alternative. We also identify the research designs and methodologies that can be used to evaluate the performance of urban built environment projects. An application in an urban renewal built environment planning and design project evaluation is presented to illustrate the proposed framework.