Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: A multilayer passive shield composed of low-activity
lead (Pb), copper (Cu), tin (Sn) and iron (Fe) was designed and
manufactured for a coaxial HPGe detector placed at a surface
laboratory for reducing background radiation and radiation dose to
the personnel. The performance of the shield was evaluated and
efficiency curves of the detector were plotted by using of various
standard sources in different distances. Monte Carlo simulations and
a set of TLD chips were used for dose estimation in two distances of
20 and 40 cm. The results show that the shield reduced background
spectrum and the personnel dose more than 95%.
Abstract: Speaker Identification (SI) is the task of establishing
identity of an individual based on his/her voice characteristics. The SI
task is typically achieved by two-stage signal processing: training and
testing. The training process calculates speaker specific feature
parameters from the speech and generates speaker models
accordingly. In the testing phase, speech samples from unknown
speakers are compared with the models and classified. Even though
performance of speaker identification systems has improved due to
recent advances in speech processing techniques, there is still need of
improvement. In this paper, a Closed-Set Tex-Independent Speaker
Identification System (CISI) based on a Multiple Classifier System
(MCS) is proposed, using Mel Frequency Cepstrum Coefficient
(MFCC) as feature extraction and suitable combination of vector
quantization (VQ) and Gaussian Mixture Model (GMM) together
with Expectation Maximization algorithm (EM) for speaker
modeling. The use of Voice Activity Detector (VAD) with a hybrid
approach based on Short Time Energy (STE) and Statistical
Modeling of Background Noise in the pre-processing step of the
feature extraction yields a better and more robust automatic speaker
identification system. Also investigation of Linde-Buzo-Gray (LBG)
clustering algorithm for initialization of GMM, for estimating the
underlying parameters, in the EM step improved the convergence rate
and systems performance. It also uses relative index as confidence
measures in case of contradiction in identification process by GMM
and VQ as well. Simulation results carried out on voxforge.org
speech database using MATLAB highlight the efficacy of the
proposed method compared to earlier work.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: In recent years, multi-antenna techniques are being considered as a potential solution to increase the flow of future wireless communication systems. The objective of this article is to study the emission and reception system MIMO (Multiple Input Multiple Output), and present the different reception decoding techniques. First we will present the least complex technical, linear receivers such as the zero forcing equalizer (ZF) and minimum mean squared error (MMSE). Then a nonlinear technique called ordered successive cancellation of interferences (OSIC) and the optimal detector based on the maximum likelihood criterion (ML), finally, we simulate the associated decoding algorithms for MIMO system such as ZF, MMSE, OSIC and ML, thus a comparison of performance of these algorithms in MIMO context.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Many industrial materials like magnets need to be
tested for the radiation environment expected at linear colliders (LC)
where the accelerator and detectors will be subjected to large
influences of beta, neutron and gamma’s over their life Gamma
irradiation of the permanent sample magnets using a 60Co source was
investigated up to an absorbed dose of 700Mrad shows a negligible
effect on some magnetic properties of Nd-Fe-B. In this work it has
been tried to investigate the change of some important properties of
Barium hexa ferrite. Results showed little decreases of magnetic
properties at doses rang of 0.5 to 2.5 Mrad. But at the gamma
irradiation dose up to 10 Mrad it is showed a few increase of
properties. Also study of gamma irradiation of Nd-Fe-B showed
considerably increase of magnetic properties.
Abstract: A simple adaptive voice activity detector (VAD) is
implemented using Gabor and gammatone atomic decomposition of
speech for high Gaussian noise environments. Matching pursuit is
used for atomic decomposition, and is shown to achieve optimal
speech detection capability at high data compression rates for low
signal to noise ratios. The most active dictionary elements found by
matching pursuit are used for the signal reconstruction so that the
algorithm adapts to the individual speakers dominant time-frequency
characteristics. Speech has a high peak to average ratio enabling
matching pursuit greedy heuristic of highest inner products to isolate
high energy speech components in high noise environments. Gabor
and gammatone atoms are both investigated with identical
logarithmically spaced center frequencies, and similar bandwidths.
The algorithm performs equally well for both Gabor and gammatone
atoms with no significant statistical differences. The algorithm
achieves 70% accuracy at a 0 dB SNR, 90% accuracy at a 5 dB SNR
and 98% accuracy at a 20dB SNR using 30d B SNR as a reference
for voice activity.
Abstract: The work allowed gaining knowledge about redox and
speciation changes of As, Cr and Sb ionic forms in Klodnica River
water. This kind of studies never has been conducted in this region of
Poland. In study optimized and validated previously HPLC-ICP-MS
methods for determination of As, Sb and Cr was used. Separation
step was done using high-performance liquid chromatograph
equipped with ion-exchange column followed by ICP-MS
spectrometer detector. Preliminary studies included determination of
the total concentration of As, Sb and Cr, pH, Eh, temperature and
conductivity of the water samples. The study was conducted monthly
from March to August 2014, at six points on the Klodnica River. The
results indicate that exceeded at acceptable concentration of total Cr
and Sb was observed in Klodnica River and we should qualify
Klodnica River waters below the second purity class. In Klodnica
River waters dominates oxidized antimony and arsenic forms, as well
as the two forms of chromium Cr(VI) and Cr(III). Studies have also
shown the methyl derivative of arsenic's presence.
Abstract: In this paper, we regard as a coded transmission over a
frequency-selective channel. We plan to study analytically the
convergence of the turbo-detector using a maximum a posteriori
(MAP) equalizer and a MAP decoder. We demonstrate that the
densities of the maximum likelihood (ML) exchanged during the
iterations are e-symmetric and output-symmetric. Under the Gaussian
approximation, this property allows to execute a one-dimensional
scrutiny of the turbo-detector. By deriving the analytical terminology
of the ML distributions under the Gaussian approximation, we confirm
that the bit error rate (BER) performance of the turbo-detector
converges to the BER performance of the coded additive white
Gaussian noise (AWGN) channel at high signal to noise ratio (SNR),
for any frequency selective channel.
Abstract: In this study, we propose a novel technique for acoustic
echo suppression (AES) during speech recognition under barge-in
conditions. Conventional AES methods based on spectral subtraction
apply fixed weights to the estimated echo path transfer function
(EPTF) at the current signal segment and to the EPTF estimated until
the previous time interval. However, the effects of echo path changes
should be considered for eliminating the undesired echoes. We
describe a new approach that adaptively updates weight parameters in
response to abrupt changes in the acoustic environment due to
background noises or double-talk. Furthermore, we devised a voice
activity detector and an initial time-delay estimator for barge-in speech
recognition in communication networks. The initial time delay is
estimated using log-spectral distance measure, as well as
cross-correlation coefficients. The experimental results show that the
developed techniques can be successfully applied in barge-in speech
recognition systems.
Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: Cognitive Radio is a turning out technology that
empowers viable usage of the spectrum. Energy Detector-based
Sensing is the most broadly utilized spectrum sensing strategy.
Besides, it's a lot of generic as receivers doesn't would like any
information on the primary user's signals, channel data, of even the
sort of modulation. This paper puts forth the execution of energy
detection sensing for AM (Amplitude Modulated) signal at 710 KHz,
FM (Frequency Modulated) signal at 103.45 MHz (local station
frequency), Wi-Fi signal at 2.4 GHz and WiMAX signals at 6 GHz.
The OFDM/OFDMA based WiMAX physical layer with
convolutional channel coding is actualized utilizing USRP N210
(Universal Software Radio Peripheral) and GNU Radio based
Software Defined Radio (SDR). Test outcomes demonstrated the
BER (Bit Error Rate) augmentation with channel noise and BER
execution is dissected for different Eb/N0 (the energy per bit to noise
power spectral density ratio) values.
Abstract: In this study, a liquid phase microextraction by hollow fiber (HF-LPME) combined with high performance liquid chromatography-UV detector was applied to preconcentrate and determine trace levels of Cyproheptadine in human urine and plasma samples. Cyproheptadine was extracted from 10 mL alkaline aqueous solution (pH: 9.81) into an organic solvent (n-octnol) which was immobilized in the wall pores of a hollow fiber. Then was back-extracted into an acidified aqueous solution (pH: 2.59) located inside the lumen of the hollow fiber. This method is simple, efficient and cost-effective. It is based on pH gradient and differences between two aqueous phases. In order to optimize the HF-LPME some affecting parameters including the pH of donor and acceptor phases, the type of organic solvent, ionic strength, stirring rate, extraction time and temperature were studied and optimized. Under optimal conditions enrichment factor, limit of detection (LOD) and relative standard deviation (RSD(%), n=3) were up to 112, 15 μg.L−1 and 2.7, respectively.
Abstract: A novel technique has been developed to generate ultra-stable millimeter-wave signal by optical heterodyning of the output from two slave laser (SL) sources injection-locked to the sidebands of a frequency modulated (FM) master laser (ML). Precise thermal tuning of the SL sources is required to lock the particular slave laser frequency to the desired FM sidebands of the ML. The output signals from the injection-locked SL when coherently heterodyned in a fast response photo detector like high electron mobility transistor (HEMT), extremely stable millimeter-wave signal having very narrow line width can be generated. The scheme may also be used to generate ultra-stable sub-millimeter-wave/terahertz signal.
Abstract: We consider the biggest challenge in speech recognition – noise reduction. Traditionally detected transient noise pulses are removed with the corrupted speech using pulse models. In this paper we propose to cope with the problem directly in Dynamic Time Warping domain. Bidirectional Dynamic Time Warping algorithm for the recognition of isolated words impacted by transient noise pulses is proposed. It uses simple transient noise pulse detector, employs bidirectional computation of dynamic time warping and directly manipulates with warping results. Experimental investigation with several alternative solutions confirms effectiveness of the proposed algorithm in the reduction of impact of noise on recognition process – 3.9% increase of the noisy speech recognition is achieved.
Abstract: Al/Cu clad sheet has been fabricated by using differential speed rolling (DSR) process, which caused severe shear deformation between Al and Cu plate to easily bond to each other. Rolling was carried out at 100 and 150oC with speed ratios from 1.4 to 2.2, in which the total thickness reduction was in the range between 14 and 46%. Interfacial microstructure and mechanical properties of Al/Cu clad were investigated by scanning electron microscope equipped with energy dispersive X-ray detector, and tension tests. The DSR process was very effective to provide a good interface for atoms diffusion during subsequent annealing. The strength of bonding was higher with the increasing speed ratio. Post heat treatment enhanced the mechanical properties of clad sheet by forming intermetallic compounds in the interface area.
Abstract: This paper addresses the performance of antenna array beamforming on Chip-Interleaved Code Division Multiple Access (CI_CDMA) system based on Minimum Mean Square Error (MMSE) detector in aeronautical mobile radio channel. Multipath fading, Doppler shifts caused by the speed of the aircraft, and Multiple Access Interference (MAI) are the most important reasons that affect and reduce the performance of aeronautical system. In this paper we suggested the CI-CDMA with antenna array to combat this fading and improve the bit error rate (BER) performance. We further evaluate the performance of the proposed system in the four standard scenarios in aeronautical mobile radio channel.