Abstract: In this article, LQR based PID controller design for
3DOF helicopter system is investigated. The 3-DOF helicopter
system is a benchmark laboratory model having strongly nonlinear
characteristics and unstable dynamics which make the control of such
system a challenging task. This article first presents the mathematical
model of the 3DOF helicopter system and then illustrates the basic
idea and technical formulation for controller design. The paper
explains the simple approach for the approximation of PID design
parameters from the LQR controller gain matrix. The simulation
results show that the investigated controller has both static and
dynamic performance, therefore the stability and the quick control
effect can be obtained simultaneously for the 3DOF helicopter
system.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: In this paper, different approaches to solve the
forward kinematics of a three DOF actuator redundant hydraulic
parallel manipulator are presented. On the contrary to series
manipulators, the forward kinematic map of parallel manipulators
involves highly coupled nonlinear equations, which are almost
impossible to solve analytically. The proposed methods are using
neural networks identification with different structures to solve the
problem. The accuracy of the results of each method is analyzed in
detail and the advantages and the disadvantages of them in
computing the forward kinematic map of the given mechanism is
discussed in detail. It is concluded that ANFIS presents the best
performance compared to MLP, RBF and PNN networks in this
particular application.
Abstract: The study in this paper underlines the importance of
correct joint selection of the spreading codes for uplink of multicarrier
code division multiple access (MC-CDMA) at the transmitter
side and detector at the receiver side in the presence of nonlinear
distortion due to high power amplifier (HPA). The bit error rate
(BER) of system for different spreading sequences (Walsh code, Gold
code, orthogonal Gold code, Golay code and Zadoff-Chu code) and
different kinds of receivers (minimum mean-square error receiver
(MMSE-MUD) and microstatistic multi-user receiver (MSF-MUD))
is compared by means of simulations for MC-CDMA transmission
system. Finally, the results of analysis will show, that the application
of MSF-MUD in combination with Golay codes can outperform
significantly the other tested spreading codes and receivers for all
mostly used models of HPA.
Abstract: This paper presents kinematic and dynamic analysis of a novel 8-DOF hybrid robot manipulator. The hybrid robot manipulator under consideration consists of a parallel robot which
is followed by a serial mechanism. The parallel mechanism has three translational DOF, and the serial mechanism has five DOF so that the overall degree of freedom is eight. The introduced
manipulator has a wide workspace and a high capability to reduce
the actuating energy. The inverse and forward kinematic solutions are described in closed form. The theoretical results are verified by
a numerical example. Inverse dynamic analysis of the robot is presented by utilizing the Iterative Newton-Euler and Lagrange dynamic formulation methods. Finally, for performing a multi-step
arc welding process, results have indicated that the introduced manipulator is highly capable of reducing the actuating energy.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: Continuation of an active call is one of the most important quality measurements in the cellular systems. Handoff process enables a cellular system to provide such a facility by transferring an active call from one cell to another. Different approaches are proposed and applied in order to achieve better handoff service. The principal parameters used to evaluate handoff techniques are: forced termination probability and call blocking probability. The mechanisms such as guard channels and queuing handoff calls decrease the forced termination probability while increasing the call blocking probability. In this paper we present an overview about the issues related to handoff initiation and decision and discuss about different types of handoff techniques available in the literature.